anko Owl Baby Walker User manual

THE ILLUSTRATIONS SHOWN IN THIS MANUAL ARE FOR REFERENCE ONLY. THE MANUFACTURER
RESERVES THE RIGHT TO CHANGE ANY SPECIFICATION OR FEATURE WITHOUT FURTHER NOTICE.
IMPORTANT! PLEASE READ CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE.
Owl Baby Walker
Instruction Manual
12
kg
6-12
months
MAXIMUM
WEIGHT OF CHILD

1 Safety Notes
CAUTION: READ THESE INSTRUCTIONS CAREFULLY BEFORE
ASSEMBLY AND USE AND KEEP FOR FUTURE REFERENCE.
THE CHILD MAY BE HURT IF YOU DO NOT FOLLOW THESE INSTRUCTIONS.
WARNING: THE WALKER IS NOT INTENDED FOR BABIES THAT
CAN ALREADY WALK UNASSISTED.
WARNING: DO NOT USE THE WALKER IF IT IS DAMAGED OR
BROKEN.
WARNING: DO NOT USE UNTIL THE BABY CAN SIT UPRIGHT BY
I TS E L F.
WARNING: CLEAN FRICTION COMPONENTS REGULARLY
TO MAINTAIN STOPPING PERFORMANCE.
WARNING: NEVER LEAVE THE CHILD UNATTENDED.
ALWAYS KEEP CHILD IN VIEW WHILE IN WALKER.
WARNING: USE ONLY ON FLAT SURFACES FREE OF OBJECTS
THAT COULD CAUSE THE WALKER TO TIP OVER.
WARNING: TO AVOID BURNS, KEEP THE CHILD AWAY FROM
HOT LIQUIDS, COOK TOPS, RADIATORS, SPACE HEATERS, FIREPLACES ETC.
WARNING - STAIR HAZARD: AVOID SERIOUS INJURY
OR DEATH. BLOCK STAIRS/STEPS SECURELY BEFORE USING WALKER.
2

1 Safety Notes (continued)
IMPORTANT:
Adult assembly required.
Read all instructions before assembly and use of the product.
This baby walker is intended to be used by children who can sit up
• unaided, from approximately 6 months. It is not intended for children
• weighing more than 12kg and/or more than 78cm in height.
Do not allow child to stand on the walker seat.
Take care when unpacking and during assembly.
Dispose of all packaging materials carefully after assembly.
Regularly check that all fittings remain tight. Tighten if required.
Inspect the product before all assembly and periodically during use.
Never use this product if there are any loose or missing fasteners, joints or
• broken parts.
Any additional or replacement parts should only be obtained from the
• manufacturer or distributer.
Never substitute parts.
CAUTION: FOR INDOOR USE ONLY
The walker is intended for indoor use only.
The wheels of the walker may scratch some painted, polished or
• wooden floors. Before using the walker, carefully assess the walker’s
• potential impact on flooring in areas where it may be used.
Conforms to ASTM F977-18 & Consumer Protection Notice No.1 of 2013.
3

2 Battery Safety
The electronic toy tray requires “3 x AAA” 1.5 Volt alkaline type batteries
(not included).
To fit and / or replace batteries: loosen the screw on the battery
compartment cover with a suitable screwdriver. Press the tab and remove the
battery compartment cover. Remove the spent batteries and fit new batteries,
ensuring that they have been fitted with the correct polarity, as shown inside the
battery compartment. Replace the battery cover and tighten the screw.
CAUTION! To prevent possible battery leakage, be sure to follow the
guidelines outlined below:
Alkaline batteries are recommended for longer battery life.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon zinc) or rechargeable batteries.
Non-rechargeable batteries are not to be recharged.
Rechargeable batteries are to be removed from the toy before being charged.
Rechargeable batteries are only to be charged under adult supervision.
Only batteries of the same or equivalent type as recommended are to be used.
Batteries are to be inserted correctly by matching the + and - polarity
• markings.
Exhausted batteries are to be removed from the toy.
The supply terminals are not to be short-circuited.
Dispose of exhausted batteries properly.
Remove batteries when product is stored for long periods of time.
• - Use a small slotted head screwdriver (not included) to open the battery
compartment door on the toy bar.
• - Insert the battery as indicated inside the battery door and re-attach the
• battery compartment door with screw.
This walker produces flashes that may trigger epilepsy in sensitized individuals.
ATTENTION! BATTERY SAFETY:
KEEP FOR FUTURE REFERENCE
4

3 Parts List
walker
x1
A B C
D
seat backrest
x1
seat cushion
x1
E
front wheels
x2
electronic toy bar
x1
F
back wheels
x2
G H
wheel pin
x2
bolts
x2
5

4 Wheels Assembly
E
E
F
F
Front
Back
Front
Back
Unpack all contents and check that all parts are present before starting
assembly. Please refer to the parts list.
1. Insert the directional front wheels (E) by aligning the pins of the wheels into
their housing located at the front of the walker. Press until they reach the white
lip.
WARNING! Ensure you have installed wheels correctly before continuing.
2. Insert the back wheels (F) into their housing located at the rear of the
walker. Ensure to align the hole in the wheel with the housing holes, then insert
the wheel pin (G) to secure in place.
Pull on wheels to ensure they are properly inserted.
G
6

5 Frame Assembly
3
2
1
1. Pull up the rear of the walker (A) until it “clicks” into position.
2. Lift the tray and seat into position.
3. Lift the front leg of walker and insert into the base. A “click” will signal when
secure.
A
7

6 Seat Unit Assembly
1. Attach the seat backrest (B) to the seat ring within the frame of the walker.
Insert the clips into the allocated slots. Push firmly until they “click” into place.
2. With the pattern side facing up, place the seat cushion (C) over the seat
backrest and ring. Gently push the crotch section through the ring to form the
seat and align the tabs with the corresponding notches.
CA
8

6 Seat Unit Assembly (continued)
3. Turn the walker upside down. Hook the seat cushion tabs onto the notches
located along the edge of the seat ring in the frame of the walker.
WARNING! Ensure all 8 tabs are securely fastened.
x8
9

7 Seat Height Adjustment
WARNING! Always remove the child before adjusting the walker.
The walker has 2 height positions.
Fasten the buckle to adjust the seat height to the desired height position.
10