Graco Dream Suite User manual

Read all instructions BEFORE assembly and USE of product.
KEEP INSTRUCTIONS FOR FUTURE USE.
Dream Suite™

Failure to follow these warnings and the instructions could
result in serious injury or death.
•PLEASE SAVE OWNER’S
MANUAL FOR FUTURE USE.
•DO NOT use product if it is
damaged or broken.
•THIS PRODUCT REQUIRES
ADULT ASSEMBLY. Follow
assembly instructions
carefully.
BASSINET MODE:
•SUFFOCATION
HAZARD Infants
have suffocated:
• In gaps between extra padding and
side of the product, and
• On soft bedding.
Use ONLY mattress/pad provided by
Graco. NEVER add a pillow,
comforter or another mattress for
padding.
• Product can roll over on soft surfaces and suffocate child.
Never place product on beds, sofas, cushions or other soft surfaces.
• FALL HAZARD: To help prevent
falls, do not use this product
when the infant begins to push
up on hands and knees, weighs
over 15 lb (6.8 kg), or reaches
3 months, whichever comes
first.
• The product must be fully
assembled and installed,
including four tubes, storage,
liner and mattress/pad, before
using. Always follow the
instructions in the owner’s
manual to set up the product.

CHANGING TABLE MODE:
FALL HAZARD: To prevent death
or serious injury,
• Always stay within arm’s reach
of your child when using the
changing table. Never leave child
unattended.
• Do not use on the bed, counter
or other surfaces.
• Do not use changing table as a
sleeping or play area.
• Weight limit for the changing
table is 30 lb (13.6 kg). Do not
use the changing table as extra
storage.
• STRANGULATION HAZARD:
• Never place baby face down on
the changing table.
• Do not carry child in changer.
• Always keep objects out of
child’s reach.
• Do not use product in an
automobile.
• Do not use product as a car
bed.
• Never leave child unattended.
• Never place a child under the
product.
• To reduce the risk of SIDS,
pediatricians recommend healthy
infants be placed on their backs
to sleep, unless otherwise
advised by your physician.
• If a sheet is used with the pad
use only the one provided by
Graco or one specifically
designed to fit the dimensions of
the product.
•ALWAYS use mattress pad.
• STRANGULATION HAZARD:
Strings can cause strangulation!
Do not place items with a string
around a child’s neck, such as
hood strings or pacifier cords.
Do not suspend strings over a
bassinet or cradle or attach
strings to toys.

FOR SAFE BATTERY USE:
Keep the batteries out of children’s reach.
Any battery may leak battery acid if mixed with a different battery
type, if inserted incorrectly (put in backwards) or if all batteries are
not replaced or recharged at the same time. Do not mix old and new
batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable
(nickel-metal hydride, nickel-cadmium) batteries.
Any battery may leak battery acid or explode if disposed of in fire or
an attempt is made to charge a battery not intended to be recharged.
Never recharge a cell of one type in a recharger made for a cell of
another type.
Discard leaky batteries immediately. Leaky batteries can cause skin
burns or other personal injury. When discarding batteries, be sure to
dispose of them in the proper manner, according to your state and
local regulations.
Remove batteries before storing product for a prolonged period of
time. Batteries left in the unit may leak and cause damage.
Recommended type batteries—alkaline disposables, 1-D (LR20-
1.5V). NEVER mix battery types. Change batteries when product
ceases to operate satisfactorily.

Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device,pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is needed.
• Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations. CAN ICES-3 (B) /NMB-3
(B).

This model may not include some
features shown below. Check
that you have all the parts for this
model BEFORE assembling your
product. If any parts are missing,
call Customer Service.
Tools required:
Philips Screwdriver
ALL MODELS
2-A Parts list
2X
2X 2X
Toy styles may
vary
2X

3-A Position Handle
1. Slide button inside of handle up
and squeeze.
NOTE: Start assembly with the
handle in this orientation. If it is not
in this orientation, follow steps 1-2.
Button
Botón
Position Handle is assembled to foot end
of bassinet/changer.

2. Rotate handle until it clicks into
place.
SNAP!

3-B Bassinet/changer Assembly
1. Lay bassinet/changer on floor
with canopy facing down.
CHECK tube is inserted in
channel above mesh exactly as
shown.
2. MAKE SURE that webbing straps
between pad and leg hub are not
twisted.
Insert tube into the top channel of
leg hub in head end of bassinet/
changer as shown.
The metal button should be facing
out when snapped in place as
shown.
SNAP!
Head End
Head End

3. CHECK tube is inserted in channel
above mesh exactly as shown.
SNAP!
4. Insert tube into the top channel of
leg hub in head end of
bassinet/changer as shown.
The metal button should be
facing out when snapped in place
as shown.
Head End