Antari WiFi-800 User manual

1
WiFi-800 USER MANUAL
2013 Antari Lighting and Effects Ltd.
English ‧中文

2

3
User Manual
Congratulations on the purchase of your new
ANTARI WiFi-800 FOG MACHINE.
Introduction
Thank you for choosing ANTARI WiFi-800 Fog Machine. You now own a state-of-the-art
machine. Prior to use, we suggest that you carefully read all of the instructions. By following
the suggestions found in this user manual, you can look forward to the reliable and
satisfactory performance of your ANTARI Fog Machine for years to come.
Please follow these operation, safety and maintenance instructions to ensure a long and
safe life-time for your fog machine.
CAUTION:
Risk of electric shock. Disconnect the appliance from the electric supply before
refilling liquid, cleaning or performing maintenance on the machine.
Danger of Electric Shock
♦Household Use only. Not designed for outdoor use.
♦Use grounded electrical outlet only. Prior to use take care to determine that the unit is
installed at the rated voltage.
♦Always unplug yourANTARI Fog Machine before filling its liquid tank.
♦Always keep fog machine in upright position.
♦Turn off or unplug the machine when not in use.
♦This machine is not water-proof. Keep this device dry.Don’t immerse in water .If moisture,
water, or fog fluid gets inside the housing, immediately unplug the unit and contact a
authorized service technician or yourANTARI dealer before using it again.
♦No user serviceable parts inside. Refer to yourANTARI dealer or qualified service
personnel.
!

4
Danger of Burns
♦This device is for adult use only and must be installed out of the reach of children. Never
leave the unit running unattended.
♦Never aim the output nozzle directly at people.
♦Fog machine output is very hot. Avoid coming within 60 cm of the output nozzle during
operation.
♦Locate the fog machine in a well-ventilated area. Never cover the unit’s vents. In order to
guarantee adequate ventilation, allow a free air space of at least 20 cm around the sides
and top of the unit.
♦Never aim the output nozzle at flames.
♦If the supply cord is damaged, it must be replaced by manufacturer or its service agent or
qualified personnel in order to avoid a hazard.
♦Always let your ANTARI Fog Machine cool down before cleaning or service.
Danger of Explosion
♦Never add flammable liquids (such as oil, gas, perfume) to the fog liquid tank.
♦Use only high-quality, water-based fog liquid that your dealer recommends. Other fog
liquids may cause clogging or damage fog machine.
♦Always make sure there is sufficient liquid in the tank. Operating this unit without liquid
will cause damage to the pump as well as over-heating of the heater.
♦If your ANTARI fog machine fails to work properly, discontinue use immediately. Drain
all fog liquid from the tank, pack the unit securely (preferably in the original packing
material), and return it to yourANTARI dealer for service.
♦Always empty fluid tank before posting or transporting this unit.
♦Never drink fog liquid. If it is ingested, call a doctor immediately. If fog liquid comes in
contact with skin or eyes, rinse thoroughly with water.
Note: Pay attention to all warning labels and instructions printed on the exterior of your
ANTARI Fog Machine
Unpacking & Inspection
Open the shipping carton and verify that all equipment necessary to operate the system has
arrived intact.
The shipping carton should contain the following items:

5
1. One unit of Antari WiFi-800 Fog Machine
2. Power cord
3. User Manual
If any equipment is missing contact your ANTARI dealer immediately.
Before beginning your initial setup on ANTARI WiFi-800 Fog Machine, make sure that there
is no evident damage caused by transportation. In the event that the unit’s housing or
cable is damaged, do not plug it in and do not attempt to use it until after contacting your
ANTARI dealer for assistance.
Setting Up
Step 1: Place the machine on a flat surface and in a suitable large area with at least 50 cm
open space around the machine.
Step 2: Fill the fluid tank with Antari approved fluid.
Step 3: Connect the machine to suitable rated power supply. To determine the power
requirement for the machine refer to the label on the back of the machine.
Step 4: Turn on the machine and allow it to heat up, while the machine is heating up the
LED status light on pushbutton will “Flash Red”. Heat up takes approximatly 2 mintues.
Once the machine has reached operating temperature, the status LED will light “Solid Red”.
Now the machine is ready for operation.
Step 5: To start making smoke, press the pushbutton locates on the handle; release
pushbutton to stop.
Step 6: To turn off the machine, put the power switch to the OFF position.
iOS Operation
Downloading the application
Login to the App Store and download Antari Fog 800 application. It allows you to control the
WiFi 800 using your iPhone or iPad.

6
Connecting iPhone/iPad to WiFi 800
Step 1: On your iPhone/iPad, select Settings > Wi-Fi > list of available Wi-Fi device will be
showed.
Step 2: Select WIFI800-XXXXXXXX, “XXXXXXXX” indicate the serial number of the
machine, is also the default SSID and password.
Step 3: Enter password to connect to the machine, and wait until the network name is
checked.

7
Controlling
The Fog 800 application provides you two ways control your WiFi 800 fog machine:
Timer Mode – allows you to set smoke duration time. Slide the time bar (from 1 to 60
seconds), press ON to start making smoke. Smoke will stop once the timer count down to
zero.
Continuous Mode – simply press the ON button to make smoke. The machine continuously
make smoke, to stop press the OFF button.
Note: If ON button is pressed and machine can not make smoke, please make sure the

8
continuous cycle button is turn on
Wi-Fi Advance Setting
Aweb-based configuration allows you to make customize configuration to your Wi-Fi setting.
To start configuration first make Wi-Fi connection with the machine, then open a web
browser, enter http://192.168.16.254 and when login window appears enter default user
name admin and password admin

9
Wireless settings > Basic
Radio On/Off
Turn radio signal on or off
On default
Off
WiFi On/Off
Turn WiFi signal on or off
On default
Off
Network Mode
Select one of the following that meets your clients
11b/g mixed mode

10
11b only
11g only
11b/g/n mixed mode default
11n only(2.4G)
Network Name(SSID)
The name of your wireless network, create a name
for your wireless network using up to 32 characters.
Broadcast Network
Name(SSID)
Enable is default setting. If Disable is selected, the
SSID of the machine will not be seen. The wireless
client will have to know the SSID in order to connect
to it.
AP Isolation
Preventing devices connected toAP from
communicating directly with each other. Default is
set to Disable.
Frequency (Channel)
Select transmitting frequency.
Wireless Settings > Security
SSID choice
Select a SSID to start configuration
Security Mode
Choose one of the following mode for data
protection:
Disable
OPENWEP
WPA-PSK
WPA2-PSK

11
WPAPSKWPA2PSK (default)
WPA Algorithms
TKIP
AES
TKIPAES
Pass Phrase
Setup password
Key Renewal interval
Enter the amount of time before the group key used
for broadcast and multicast data is changed (3600
is default)
Administration > Management
Account
Change login account name (default is admin)
Password
Change login password (default is admin)

12

13
Technical Specifications
Model
WiFi-800
Power Supply
AC100-120V, AC 220-240V / 50HZ - 60HZ
Power Consumption
800 W
Output Volume
3000 Cubic Feet / Min
Tank Capacity
0.8 Liter
Fluid Consumption
60 Min. / 0.8 Liter
Weight
4.1 kg
Dimensions (LxWxH)
315 x 128 x 220 mm
Optional Controllers
Z-10 On/Off Controller, Z-40 Timer Controller, Z-50
Wireless Controller
First Heat-up Time
1.7 min
Optional Controllers for WiFi-800
♦Z-10: 10 meter wired remote controller with 1/4 inch jack plug. The red light indicates that
the unit is receiving power. When the fog machine has reached operating temperature
the green light on this remote controller will light up, indicating that the operator may
begin fog emission by pressing the red button. The green light flashes during fog
machine warm-up and re-heating cycles (approx. 1-2 minutes), and stays ON when the
machine becomes operational. The Z-10 features the “toggle switch’’ function: press
once for continuous “ON”, press again to release continuous “ON” function
♦Z-40: 10 meter wired remote controller with 1/4 inch jack plug. Its two knobs allow users
to customize the duration and interval of fog output time. Press the yellow TIMER-button
to activate the timer function. Adjust the interval between each fog emission (within the
range of 10 to 250 seconds) by means of the INTERVAL control knob. Adjust the duration
of each fog emission (within the range of 10 to 120 seconds) by means of the
DURATION control knob. When pressed, the green FOG button overrides all other
control functions and activates maximum output.
♦Z-50: Wireless remote controller with 1/4 inch jack plug. A remote operation is possible
up to a distance of 50 meters in open area. Keep the red button pressed for fogging.

14
Z-10, Z-40, Z-50 Remote Controller
Performance Note
♦All fog machines develop condensation around the output nozzle. Because this may
result in some moisture accumulation on the surface below the output nozzle, consider
this condensation when installing your unit.
♦All fog machines may sputter small amounts of fog occasionally during operation and for
a minute or so after being turned off.
Maintenance
Do not allow the fog liquid to become contaminated. Always replace the caps on the fog
liquid container and the fog machine liquid tank immediately after filling. After every 40 hours
of operation, it is recommended to use distilled water to run a cleaning process.
The recommended cleaning regimen is as follows:
1. Empty all fog liquid from the machine. Add distilled water to liquid tank. Plug unit in and
begin warm up.
2. Run the unit in a well-ventilated area and run the fog machine briefly. Do not allow the
pump to run dry.
3. Cleaning is now completed. Empty the water left inside liquid tank and refill with fog liquid.
Run the
machine briefly again.

15
Note:
Cleaning your fog machine regularly can help reduce replacement and repair cost.
After a certain period time of usage, all fog machines tend to clog due to the thick
consistency of fog liquid and the high temperature at which it vaporizes. However, a properly
maintained fog machine should provide longer and more reliable life-time.
Storage
1. When machine is not in use, store it in a cool and dry place.
2. It is strongly recommended to test-run the machine on a monthly basis in order to
achieve its best condition.A test-run consists of warming up the machine followed by a
few minutes of emission. After that, follow Step 1 under Storage.
Please read and save these instructions.

16
Antari WiFi800 煙霧機
感謝您選用 Antari 煙霧機產品，現在您已經擁有高科技的專業煙霧機,在開始使用之前，我
們建議您先仔細閱讀本說明書，遵循使用手冊中的說明,這會有助於您在使用 Antari 煙霧機
時得心應手，達到最滿意的煙霧效果，對於機器的使用壽命也更為延長。
特別注意：
請在連結電源之前，先填裝好煙霧油，器使用完畢及搬運前，請先確認清空煙霧油桶.
避免觸電的安全使用方式:
請保持機器乾燥，僅於室內使用，,本產品非為室外使用所設計。
使用前請小心判定電壓級數，伏特及機型，當使用所有電壓規格的機種請應配合三向接地
型插座使用。
填充煙霧油至油桶前，請先拔掉插頭。
請保持機器橫放，勿傾斜放置。
不使用時請關機,長時間不使用時請拔掉插頭。
本產品之設計為不防水，遇潮濕或浸水或煙霧油滲出時請即刻拔掉插頭並擦乾，在下次使
用前，聯絡技術人員或 Antari 的代理商檢修。
本包裝中未附服務零件，敬請聯繫 Antari 代理商，或洽詢合格技術人員。
避免燃燒的安全使用方式:
機器內部並無一般使用者可變動之結構，請勿任意打開上蓋及作任何更改的動作，否則可
能造成起火的危險！
機器僅限成人使用，安裝煙霧機之地點應避免兒童可處及之出，請於外出離去時確實關閉
!

17
電源。
請勿將機器噴嘴對著人體及動物直射。
煙霧機所產生的煙霧溫度較高，機器運作時，請遠離噴嘴 50CM 以上。
請將煙霧機放置於通風良好的地方，請勿遮蓋機器散熱部分，為確保適度通風，機器的上
方及周圍請預留 20CM 空間。
請勿將機器噴嘴對準火焰。
當機器運作時，噴嘴輸出部分之溫度高達攝氏 200 度，請將任何物品放置離機器 50CM。
清潔、從事維護及收納機器時，請先確認機器已經完全冷卻。
避免爆炸的安全使用方式:
請勿將任何可燃性液體(例如油脂,瓦斯,香水)，放置於煙霧油槽中，並請使用前詳細閱讀
說明書。
請使用代理商所推薦的 Antari 高品質 FLR / FLG 水性煙霧油，任意使用其他煙霧油產品，
可能導致堵管現象甚至造成內部零件腐蝕。
請確認煙霧油槽中有足夠的煙霧油，以免造成煙霧機幫浦空轉過熱。
若您的 Antari 機器有任何不當運轉情況時，請即刻停止使用，倒出煙霧油，機器冷卻後，
仔細包好本產品(建議以原包裝)送至代理商或經銷商處維修。
請記得在運送或郵寄本產品前，確定完全傾倒出所有在油桶中的煙霧油。
煙霧油不能飲用，誤飲時，如有任何不適請立即就醫，若不甚接觸眼睛，請即刻以水清洗。
建議:在使用本機器之前，詳細的閱讀一次印刷在機器上蓋板及後背板的警語標示.
拆除包裝及檢視機器
請打開包裝確認機器運作的所有設備齊全，請參考配置圖，確認您所購買的機型應包括之項
目，倘若有缺少任何項目，請即刻聯絡 Antari 經銷商。 機器出廠時應包含以下物件:
1. 機器 一部

18
2. 電源線一條
3. 使用說明書一份
在開始安裝機器之前，,請先確認本產品未因運送過程造成外部的損壞，若機器外殼、控制器
或電源線有任何損壞，請勿插上插頭，並請勿使用，馬上與 Antari 代理商或經銷商聯繫。
安裝設置
步驟 1：將機器放置在平坦的表面上，並且在機器四周保留至少要有 50 公分的空曠空間。
步驟 2：將 Antari 指定的煙霧油注入機器油箱。
步驟 3：將本機連接到合適的額定電源。機器功率要求資訊，請參閱機器背面的技
術標籤。
步驟 4：打開機器開關，進行加溫，此時手把按鈕上的 LED 狀態指示燈會“閃紅燈”。溫機的時
間需要約 2分鐘。一旦機器達到工作溫度，狀態指示燈將亮起“紅色常
亮”。表是機器為準備完成。
步驟 5：開始噴煙動作，按下手把上的按鈕釋放按鈕來停止。
步驟 6：關閉機器時，把電源開關置於 OFF 位置。
程式下載
登入 App Store 下載 Antari Fog 800 應用程式,這個程式可經由你的 iPhone 或iPad 來操
控WiFi-800
 將 iPhone/ iPad 連結到 Wifi 800
步驟 1. 進入到你的 iPhone/ iPad 的設定選單 >選取 Wi-Fi > 系統會列出所有可用的 Wi-Fi
裝置
步驟 2. 選擇 WiFi800-XXXXXXXX, “XXXXXXXX” 所顯示出的機器序列號碼,這同時也是
SSID 的系統預設值和密碼

19
步驟 3. 輸入密碼以連結機器,並等待直到網路名稱顯示打勾即完成連結
 控制
Fog 800 應用程式提供兩個方式來控制你的 WiFi 800 型煙霧機

20
定時模式 -可以設定煙霧持續輸出時間,滑動時間桿, ( 從1到60 秒)按壓 ON 開始輸
出煙霧.時間開始倒數,煙霧將停止於結束倒數直到 0.
連續噴煙模式 –按壓螢幕上 ON 按鍵,機器將持續不斷的輸出煙霧,如果希望結束,只要按壓
螢幕上的 OFF 鍵
注意 : 如果按壓了 ON 的按鍵 , 機器無法噴煙 , 請確認螢幕上的機器持續輸出循環鈕 是
啟動的
Wi-Fi 進階設定
透過網頁設定介面，使您可以自定義 Wi-Fi 模組的相關設置。開始設置前請確認已和機器完成
連結，然後打開一個網頁瀏覽器，輸入 http://192.168.16.254，當出現登錄窗口輸入確認用戶
名admin 和密碼 admin