Antari X-510PRO User manual

1
X-510PRO , X-515PRO FOG MACHINE
USER MANUAL
English Français Deutsch• • •
2011 Antari Lighting and Effects Ltd.

2

3
Congratulations on the purchase of your new
ANTARI X-PRO SERIES Fogger
Introduction
Thank you for choosing an ANTARI Fogger of the X-PRO SERIES. There are two models available:
the X-510PRO (1000W) and the X-515PRO (1500W). Both units are rugged and powerful
state-of-the-art machines. Besides their ability to operate silently, these new models are user-friendly
in terms of controlling and operating. For Antari X-515PRO fog machine, an optional W-DMX function
(W-DMX) is available. Prior to use, we suggest that you carefully read all of the instructions. By
following the suggestions found in this user manual, you can look forward to the reliable and
satisfactory performance of your ANTARI Fog Machine for years to come.
Important Safeguards
-Danger of Electric Shock
* Keep this device dry.
* For inside use only. Not designed for outside use.
* For all models, use 3-prong grounded electrical outlet only. Prior to use take care to
determine that the unit is installed at the rated voltage.
* Always unplug your ANTARI Fog Machine before filling its tank.
* This machine is not water- or splash-proof. If moisture, water, or fog liquid gets inside the housing,
immediately unplug the unit and wipe off the moisture and keep it dry.
Danger of Burns
* Structural modification inside the machine is not allowed at anytime. Please do not attempt to
modify the machine by removing the cover, otherwise burns may result.
* For adult use only. Never leave the unit running unattended.
Cautions
Risk of electric shock. Disconnect the appliance from the electric
supply before removing the cover.
Note: There are no user serviceable parts inside.
!

4
* Never aim the output nozzle directly at people.
* Machine will warm up when operating, locate the fog machine in a well-ventilated area. Never
cover the unit's vents. In order to guarantee adequate ventilation, allow a free air space of at
least 30 cm around the sides and top of the unit.
* Never aim the output nozzle at open flames.
* The output nozzle becomes very hot during operation (200°C). Keep flammable materials at
least 50 cm away from the nozzle.
* Always allow your ANTARI X-PRO SERIES Fogger to cool down before attempting to clean or
service it.
Danger of Explosion
* Never add flammable liquids of any kind (oil, gas, perfume) to the fog liquid.
* Use only the high-quality, water-based ANTARI recommended FLG / FLR fog liquid. Other fog
liquids may cause clogging or damage to internal parts.
* Always make sure there is sufficient liquid in the fog liquid tank. Operating this unit without liquid
will cause overheating.
* If your ANTARI fog machine fails to work properly, discontinue use immediately. Drain all fog
liquid from the tank, pack the unit securely (preferably in the original packing material), and return
it to your ANTARI dealer for service.
* Always drain tank before mailing or transporting this unit.
* Never drink fog liquid. If it is ingested, call a doctor immediately. If fog liquid comes in contact with
skin or eyes, rinse thoroughly with water.
- Unpacking & Inspection
Open the shipping carton and verify that all equipment necessary to operate the system has arrived
intact.
The shipping carton should include the following items:
1. One unit with power cable of the X-PRO SERIES series: X-510PRO or X-515PRO
2. X-10PRO Control Module with cables
3. Fluid tank
4. User manual
Important:
Pay attention to all warning labels and instructions printed on the exterior of
your ANTARI X-PRO SERIES Fogger.
!

5
Optional Accessories:
1. Hanging bracket
2. Drip tray
3. X-30PRO Wireless Control Module
4. FX-510, FX-515 Flightcase
Before beginning with the initial setup of your X-PRO SERIES Fogger, make sure that there is no
evident damage caused by transportation. In the event that the unit's housing or cable is damaged,
do not plug it in and do not attempt to use it after having contacted your Antari dealer for assistance.
Setup
1. Remove all packing materials from shipping box. Check that all foam and plastic padding is
removed, especially in the nozzle area.
2. Place fog machine on a flat surface and remove fog liquid tank cap.
3. Fill unit about 3/4 full. Use Antari Fog Fluid only. Antari X-510PRO and X-515PRO Foggers only
work with uncontaminated Antari FLG/FLR Fog Fluid. Other fluids may cause possible clogging
problems and could result in the production of unhealthful fog. The use of other fluids will void the
warranty of the Antari X-510PRO and X-515PRO. When filled, place cap back on liquid tank.
Operation
* The plug is at a position that is accessible when the machine is in use.
Plug power cord into a grounded electrical outlet. Turn power switch on the rear of unit to “ON”
position. Warm-up is completed when the display on control module shows “Ready to Fog”.
* To emit fog, press the appropriate button on the X-10PRO Control Module for the desired length
of time.
* The Control Module’s display will cycle “Warming up” and “Ready to Fog” while the machine
re-heats to the proper operating temperature.
* When the fluid is running low, the LED inside the tank chamber starts blinking until the tank is
refilled again.
* Always monitor liquid level to prevent interrupted operation.
Caution: “Visibility during operation is reduced”.
WARNING
Use of any fluid other than ANTARI fog fluid or modification or attempt to unauthorized
repair of the X-Seies PRO Fogger will immediately invalidate the warranty.
!

6
Hanging Bracket
The unit may be installed at floor level or suspended overhead via the hanging bracket. If the unit is to
be mounted using the bracket, it is important that the fog does not shoot directly at any one's face.
Whatever installation method you choose, do not allow the unit to have more than a 15° angle of
inclination.
If you experience low output, pump noise or no output at all, unplug immediately. Check fluid level, the
external fuse, control module connection, and power from the wall. If all of the above appears to be
O.K., plug the unit in again. If fog does not come out after holding the control module button MANUAL
down for 30 seconds, check the hose attached to the tank to make sure there is fluid going
through the hose. If you are unable to determine the cause of the problem, do not simply continue
pushing the control module button, as this may damage the unit. Return the machine to your ANTARI
dealer.
Menu Settings With The Button FUNCTION
Setting time intervals for timer operation
Press the button FUNCTION until the display indicates「Interval Set」. Use the buttons
UP and DOWN to adjust the intervals between the individual fog outputs in timer
mode within the range of 1 and 200 seconds.
Important
Always monitor tank fluid level when you are fogging. Running a fog machine with no
fluid can permanently damage the unit.
!

7
Setting the output duration for timer operation
- Press the button FUNCTION until the display indicates「Duration Set」. Use the buttons
UP and DOWN to adjust the duration of the fog outputs in timer mode within the range
of 1 and 200 seconds.
Setting the fog output volume for timer operation
- Press the button FUNCTION until the display indicates「Timer Out」. Use the buttons
UP and DOWN to adjust the fog output volume in timer mode within the range of 1 % and 100
%.
Setting the fog output volume for continuous operation
- Press the button FUNCTION until the display indicates「Volume Out」. Use the buttons
UP and DOWN to adjust the fog output volume in continuous mode within the range of
1 % and 100 %.
- To set the unit to continuous fog output, select 「NON STOP BURST」below a value of 1 % or above
a value of 100 %.
Setting the DMX512 address
Press the FUNCTION until the display indicates「DMX 512 Add」. Use the buttons UP
and DOWN, to set the machine to the same address as on your DMX controller. Please refer
to the chapter DMX512 settings for more information on DMX operation.
Turning the heater on or off
Press the FUNCTION until the display indicates「Heater On」. Use the button
MANUAL, to switch the heater on or off.

8
Continuous operation
Press the button VOLUME , to activate continuos fog output. The display indicates「Volume」
followed by the value that was set in menu item「Volume Out」or 「NON STOP BURST」. To stop
the fog output, press the button VOLUME once again.`
Manual operation
For immediate fog output at the maximum volume of fog, keep the button MANUAL pressed.
The display indicates「Manual Output」. As soon as you release the button, the fog output will stop.
The manual operation will take priority over the continuous operation and the timer operation. Even if
one of these operating modes is activated, the fog machine will always emit the maximum volume of
fog when the button MANUAL is pressed.
Timer operation
In the timer mode, the fog machine will automatically emit fog. The time intervals, duration and fog
volume depend on the corresponding menu settings. Press the button TIMER , to activate the
timer mode. The display indicates the set time interval. The unit counts down to 0 seconds and emits
fog. To deactivate the timer mode, press the button TIMER again.

9
Antari X-30PRO Control Module Operation
X-30PRO Wireless Control Module Operation
All the X-10PRO features plus wireless capability.
The wireless control module X-30PRO consists of a transmitter equipped with two buttons for fog on
and off, and a receiver pre-attached to the panel of each X-30PRO.
* Transmitter:
With the transmitter it is possible to emit fog via radio over a distance of up to 50 meters. The
transmitter is compatible to any receiver of the X-30PRO and can control an unlimited number of
machines in parallel.
Press the button “A”, to emit fog. The button “A” has the same function as the button VOLUME on the
control panel, i.e. the fog output depends on the setting of menu item »Volume Out«. The display
indicates 「Volume」followed by the defined value or 「NON STOP BURST」when continuous fog
output was selected. To stop the fog output, press the button “B”.
* Receiver:
The receiver is tested and pre-attached to the panel of each X-30PRO. Please do not try to remove it.
The receiver responds to up to 5 different transmitters that are registered with the machine. The
included transmitter has been registered to the machine before shipment. It can be directly operated
without any start-up setting.

10
-Registering transmitters
To operate the machine with a different transmitter than the included one, or to operate it with up to 5
different transmitters, each transmitter must be registered first. For this purpose, turn on the machine.
When the display indicates 「Wireless Setup」, press the button “A” 1 second on each transmitter.
Thus the previous transmitters are cleared from the memory of the receiver. The setting must be
completed within 15 seconds after switching on the machine. Then the machine will automatically exit
the transmitter setting mode. The display shows 「Wireless Setup OK」. At this point, no further
transmitter can be added.
If no transmitter is registered when the machine is switched on, the memory of the receiver will keep
the record of the previous operation.
Setting Example 1:
In order to register several transmitters with a machine, turn on the machine. When the display
indicates 「Wireless Setup」, press the button “A” 1 second on each transmitter within 15 seconds to
establish the signal transmission.
Setting Example 2:
In order to use 1 transmitter to control 2 or more machines, turn on the machines respectively. When
the displays indicate「Wireless Setup」, press the button “A” 1 second on the transmitter within 15
seconds to establish the signal transmission.
- Battery change on the transmitter
If the range of the transmitter decreases, the battery is probably exhausted and must be replaced. For
this purpose, take off the housing cover and remove the used battery. Insert a fresh battery as
indicated in the battery compartment and refit the housing cover.
- Switching the wireless function on and off
Press the button FUNCTION until the display indicates 「Wireless On」. Use the buttons UP and
DOWN to deactivate the wireless function (indication 「Wireless Off」) and to reactivate it (indication
「Wireless On」).
* Note: When warming-up process is completed and wireless function is activated the LCD screen
indicates “Ready To Fog W”. (“W” means Wireless) On the contrary, when the wireless function is
deactivated the LCD screen shows “Ready To Fog” (Without “W”).