Antari M-11 User manual

1
© 2019 Antari Lighting and Effects Ltd. www.antari.com
M-11
Stage Fog Machine
User Manual
- ENGLISH
©2019 Antari Lighting and Effects Ltd.

2
© 2019 Antari Lighting and Effects Ltd. www.antari.com
Safety Information
Please read the following safety information carefully before operating the machine.
This information includes important safeguards about installation, usage, and
maintenance. Pay attention to all warning labels and instructions in this manual and
printed on the machine.
If you have questions about how to operate the machine safely, please contact your local Antari
dealer for help.
Keep this device dry.
Always connect to a grounded circuit to avoid risk of electrocution.
Before connecting the machine to power, always check the voltaged indicate on the machine
matches to your local AC voltage. Do not use the machine if AC power voltage does not match.
Disconnect the machine from AC power before servicing and when not in use.
If the supply cord is damaged, contact your local Antari dealer for replacement.
This product is for indoor use only! Do not expose to rain or moisture. If fluid is spilled,
disconnect AC power and clean with a damp cloth. If fluid is spilled onto electronic parts,
immediately unplug the machine and contact your local Antari dealer for advice.
No user serviceable and modifiable parts inside. Never try to repair this product, an
unauthorized technician may lead the machine to damage or malfunction.
For adult use only. Children being supervised not to play with the machine. Never leave the
machine running unattended.
The machine is not to be used by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge.
Installed in a well ventilated area. Provide at least 50 cm space around the machine.
Never add flammable liquid of any kind to the machine.
Make sure there are no flammable materials close to the machine while operating.
Only use Antari fluid. Other fluid may lead to heater clog and malfunction.
If the machine fails to work, unplug the machine and stop operation immediately. Contact
your local Antari dealer for .
Before transporting the machine, make sure the fluid tank is completely drained.

3
© 2019 Antari Lighting and Effects Ltd. www.antari.com
Smoke fluid may present health risks if swallowed. Do not drink smoke fluid. Store it securely.
In case of eye contact or if fluid is swallowed immediately look for medical advice.
Unpacking and Inspection
Immediately upon receiving the machine, carefully unpack the carton, check the content to ensure
that all parts are present and have been received in good condition. If any parts appear damaged or
mishandled from shipping, notify the shipper immediately and retain the packing material for
inspection.
What is included: 1 x M-11 Stage Fogger
1 x Power Cord
1 x User Manual
Product Dimensions
Product Overview
XLR 5-Pin DMX Connector
XLR 3-Pin DMX Connector
Wireless Receiver (W-2 Wireless Remote)
Two rotary knobs (Timer / Volume)
L 674.5 mm
H 284.3 mm
W 319.8 mm
Neutrik TRUE 1 Power
Connector

4
© 2019 Antari Lighting and Effects Ltd. www.antari.com
Setting Up
Step 1: Place the machine on a flat surface and in a suitably large area with at least 50 cm of open
space around the machine.
Step 2: Fill the fluid tank with Antari approved fluid.
Step 3: Connect the machine to a suitably rated power supply. To determine the power requirement
for the machine refer to the label on the back of the machine.
Always connect the machine to a protected circuit and ensure it is properly grounded to
avoid risk of electrocution.
Step 4: Turn on the machine and allow it to heat up. Heat up takes approximately 13 mintues. Once
the machine has reached operating temperature, the LCD display will show “Ready To Fog”. Now the
machine is ready for operation.
Step 5: To start making fog, locate the rotary knob on the right side of control panel, and press the
rotary knob to start making fog.
Step 6: To turn off the machine, press rotary knob again button and turn Powercon to the OFF
position.
Operation
Control Panel Operation
The machine can be operated with the onboard digital control interface.
T I MER VOL UM E
HOLD 3 SECONDS
Antari M-11
Ready To Fog

5
© 2019 Antari Lighting and Effects Ltd. www.antari.com
Operation - Timer Mode
Rotary knob
Action
Description
Left
Press once
Activate timer mode
Right
Press second time
Deactivate timer mode
Right
Rotate
Adjust output volume
Operation –Volume Mode
Rotary knob
Action
Description
Right
Press once
Activate volume mode
Right
Press second time
Deactivate volume mode
Right
Rotate
Adjust output volume
Setting
Rotary knob
Action
Description
Left
Press and hold for 3 seconds
Enter setting menu
Left
Rotate
Scroll through menus
Left
Press
Press once to enter
Left
Rotate
Adjust for preferred value
Right
Press
Escape from menu
Control Menu
Main Menu
Level 1
Level 2
DMX
Address
001-512
Channel Mode
1/3
Link Mode
Wired/Wireless
W-DMX
Unlink
Timer
Interval
5 –200 sec
Duration
1 –200 sec
Output Level
0 –100%
Manual
Output Level
0 –100%
Priming
Start/Stop
Heater
On/Off
Information
Software Version
VX.X
Wireless Signal
●: W-DMX present

6
© 2019 Antari Lighting and Effects Ltd. www.antari.com
◎: No DMX present
⊙: Link to TX lost
○: Not assigned
Fluid Level
Fine/Empty
Device Hour
XX Hour
Setting
Continuous Output
On/Off
Pump Mode
Single/Dual
Wireless Remote
Pair/Unpair
Fluid Sensor
On/Off
LCD Backlight
Auto Off/Low/Normal
Keypad Sound
On/Off
Auto Start
On/Off
Factory Reset
Proceed
Language
EN/ZH
DMX Connector Pin Assignment
The machine provides both 3 and 5-pin XLR connector for DMX connection. The diagram below
indicates pin assignment information.
Pin
Function
1
Ground
2
Data-
3
Data+
4
N/A
5
N/A
DMX Operation
Making the DMX Connection –Connect the machine to a DMX controller or to one of the machines
in the DMX chain. The machine uses both 3-pin and 5-pin XLR connector for DMX connection, the
connector is located on the rear of the machine.

7
© 2019 Antari Lighting and Effects Ltd. www.antari.com
OUT IN
DMX Channel Function
1 Channel Mode
DMX Value Range
Function
Output Level
0 –4
Off
5 –255
1 –100%
3 Channel Mode
DMX Value Range
Function
Output Level
0 –4
Off
5-255
1 –100%
Heater
0-126
Off
127-255
On
Pump
0 –126
Single
127-255
Dual
RDM Control
The M-11 Stage Fogger is RDM enabled, allowing control system to configure, mointor and manage.
See below table for supported RDM parameters
Value
RDM Parameter ID’s
GET Allowed
SET Allowed
0x0001
DISC_UNIQUE_BRANCH
0x0002
DISC_MUTE
0x0003
DISC_UN_MUTE
0x0030
STATUS_MESSAGE
O
0x0050
SUPPORTED_PARAMETERS
O
0x0051
PARAMETER_DESCRIPTION
O
0x0060
DEVICE_INFO
O
0x0070
PRODUCT_DETAIL_ID_LIST
O

8
© 2019 Antari Lighting and Effects Ltd. www.antari.com
0x0080
DEVICE_MODEL_DESCRIPTION
O
0x0081
MANUFACTURER_LABEL
O
0x0082
DEVICE_LABEL
O
O
0x00A0
LANGUAGE_CAPABILITIES
O
0x00B0
LANGUAGE
O
O
0x00C0
SOFTWARE_VERSION_LABEL
O
0x00E0
DMX_PERSONALITY
O
O
0x00E1
DMX_PERSONALITY_DESCRIPTION
O
0x00F0
DMX_START_ADDRESS
O
O
0x0200
SENSOR_DEFINITION
O
0x0201
SENSOR_VALUE
O
0x0400
DEVICE_HOURS
O
0x1000
IDENTIFY_DEVICE
O
O
Wireless Operation
Wireless remote control system W-2 consists of a transmitter equipped with four buttons to activate,
deactivate, increase and decrease fog output and an onboard receiver attached to the rear panel of
M-11 fog machine.
W-2 Wireless Transmitter
Press [A] button to emit fog. Press [B] button to stop. Press [C] button to increase output volume. Press
[D] button to decrease output volume.
In an unobstructed open space the effective distance is 50 meters, usage depending on obstacle level
the effective distance is 10-25 meters.
Wireless Receiver

9
© 2019 Antari Lighting and Effects Ltd. www.antari.com
Registering a transmitter
Transmitters can be paired or deleted from the receiver. Each receiver can pair up to 5 transmitters.
Follow the steps below to pair or delete a transmitter from a receiver.
Step 1: Press and hold the left rotary knob for 3 seconds to enter setting menu.
Step 2: Rotate the rotary knob to find the “Wireless Detect” menu.
Step 3: Follow the menu instruction to pair or delete a transmitter.
Transmitter battery replacement
If the effective distance seems to decrease, it is possible the battery level is low and requires
replacement. In order to replace the battery, undo the three screws on the back of transmitter to
release the cover. Replace with the same type and specification of battery which is 27A 12V
Fluid
Only use Antari FLR/FLG water-based liquid for the M-11
Stage Fogger. The machine is tested and calibrated with this
liquid to get the best output performance. Warranty will be
voided if any other type of liquid is used, improper use of
liquid may lead to machine failure and malfunction.
Service and Maintenance
․Do not allow the machine to become contaminated.
․Remove dust from air vents with air compressor, vacuum or a soft brush.
․Only use a damp cloth to clean the casing.
․Before storing run distilled water through the system to help prevent condensing the pump or
heater.
․It is recommended to run the machine on a monthly basis in order to achieve best
performance and output condition.
․Excessive dust, liquid and dirt built up will degrade performance and cause overheating.
Breaker Reset
Disconnect AC power before resetting the breaker. Only replace fuse with same type
and rating.

10
© 2019 Antari Lighting and Effects Ltd. www.antari.com
Step 1: Disconnect AC power.
Step 2: Flip breaker to ON position.
Step 3: Turn on machine for testing.
Breaker
100-120V = 15A 250V
220-240V = 7A 250V
Technical Specifications
- Input voltage
- Rated power
- Warm-up time
- Fluid consumption
- Fluid tank capacity
- Compatible fluid
- Ambient temp/ range
- Control
- DMX channels
- Connection
- Optional accessories
- Dimension
- Weight
US model : AC 100-120V, 50 / 60Hz 13.3A
EU model : AC 220-240V, 50 / 60Hz 6.67A
1600 W
13 minutes (approx)
400 ml / min (100% output)
10 Liters
Antari FLG 10 Heavy Fog Fluid
Antari FLR 10 Light Fog Fluid
0℃- 40℃(32℉-104℉)
DMX 512, Timer, Manual
Wireless (Optional)
Wireless DMX (Optional)
1 or 3 channels
Neutrik TRUE1 Connector (Power)
XLR 3-pin and XLR 5-pin (DMX)
W-DMX-PCBR Wireless DMX
WTR-20 Wireless
WTR-70 Wireless DMX and Remote
L 674.5 W 319.8 H 284.3 mm
25 kg (55.1 lbs)