Antec T1 SPORT User manual

Assembly Instructions
●Read over the manual before you begin. Two people are suggested for assembly.
●Please follow this instruction manual to assemble this chair, wrong way may cause you to be injured or the chair may damaged.
●We suggest two or more people assemble the chair and suggest to use gloves to prevent possible injuries during assembling.
●To avoid danger of suffocation, keep the plastic bags for packaging away from babies and children.
Content Checklist
1 x M8 Screw
1 x Tilt Mechanism
1 x Allen Key2 x Phillips screw6 x Cushion Gasket
4 x Plastic Caps
1 x Wheel Base
1 x Side Cover 5 x Caster 1 x Hydraulic Gas Lift
1 x Backrest (with 4 x M8 screws pre-installed) 1 x Chair Base (with 4 x M8 screws pre-installed)
T1 SPORT
Antec Gaming Chair

Chair Installation
1Place the Chair Baseupside-down on a soft surface , remove
the screws on the Chair Base.3Insert the 5 Casters into the Wheel Base. Push firmly to lock them into place.
5Align the top of the Hydraulics into the bottom of the
Tilt Mechanism, push to lock it into place.
4Position the Hydraulics into the Wheel Base and place
the Hydraulic Sleeve over it.
2Position the Tilt Mechanism and the Cushion Gaskets in the
correct direction. Install the Tilt Mechanism by diagonally
tightening the screws into the Chair Base with the Allen Key.

6Using the ALLEN KEY, unscrew the 4 M8 pre-mounted
screws, attach the backrest to the seat.
Starting with the right side, attach the backrest to the metal
brackets with the 4 M8 screws using the ALLEN KEY. (Note
that do not tighten the screws until the four screws are
fully installed in the hole.)
7While firmly pushing SIDE COVERS into place, use the ALLEN
KEY to secure the SIDE COVERS with the 2PHILLIPS SCREWS.
Congratulations, you have completed the installation of the chair.

Care Instructions
‧ Keep boulies chair tidy by vacuuming its seams with a crevice tool.
‧ Dust regularly using a clean, lint-free, slightly damp soft cloth and wipe the area
clean.
‧ Avoid direct sunlight and keep the chair away from heat sources to protect its
leather.
‧ Clean spills quickly. Blot away with a clean cloth, but do not rub.
‧ Clean the casters by wiping off dirt with a scrub brush. Vacuum out dust caught
inside of the wheels.
‧ For further cleaning, pull off the wheels and wipe them down with a surface cleaner
and a clean rag.
Safety Information & Return/Exchange Policy
The maximum recommended user weight of the Master Series/Ninja
Pro Series is up to 135 kg / 300 pounds, the Elite Series is up to 120 kg
/ 270 pounds.
Don't use boulies chair in an abusive manner. The chair is not liable
for any damages resulting from improper assembly and usage.
The original packaging can be conveniently reused for a boulies chair
return or exchange. noblechairs accepts returns that are properly
packaged.
Features
BACKREST RECLINE
Pull up on the lever and slowly lean
back until the preferred position is
achieved, then slowly return the lever
to its starting position. Ensure the
lever locks back in place.
LUMBAR ADJUSTMENT
Turn the knob clockwise to increase the lumber support, anticlockwise to decrease. Do not attempt to turn past the
maximum and minimum.
4D ARMRESTS
Press and hold the 1) lever on the
outside of the armrest to adjust
height, 2) inner side button to adjust
sideways, and 3) front button to adjust
front, back, and angle.
TILT TENSION
Turn the knob clockwise to loosen
the rocking tension of the chair,
anticlockwiseto tighten. Adjust
according to your weight.
MULTI-TILT MECHANISM
1) Right lever( while seated): Pull up
to adjust height. 2) Left lever (while
seated): Push down/pull up to lock/
unlock the tilt mechanism.
MASTER Only