Anvis FacePass Pro User manual

Installation Environment
Installation Steps
Before Installation:
The FacePass Pro working temperature：0℃---45℃，working humidity：20%---80%
Direct sunlight would cause great impact on the face recognition performance. So the device is not allowed to be installed
outside. Please install the device indoor and avoid strong light shining straight into the camera.
The best verification distance of FacePass Pro is 11.8’’-31.5’’ (30-80 cm)
and the best image capture angle of the camera is level：±20°,
vertical：±20°.The recommended installation height is 43.3’’ (110cm)
from the ground. In this position the FacePass Pro can capture body
height rangeing is 57’’-76.8’’ (145-195 cm) the person’s face image is
in valid verify distance.For the actual installation height please refer
to the user’s height.
Step 1: Installation Position
Installation Position
43.3”
(110cm)
Ground
57”
(145cm)
31.5”
(80cm)
11.8”
(30cm)
76.8”
(195cm)
Figure（1）
Step 2: Holing fot the Steel Bracket
（1）Please refer to the size of the steel bracket, mark out the screw and
wiring holes. Make sure the back board is on horizontal position.
（2）Drill the hole (Recommended dia.6 mm).
Step 3: Fixing Steel Bracket
（1）Fix the steel bracket on the wall with self tapping screws.
（2）Pull all the cables out from the wiring hole of the steel bracket.
Step 4: Fixing the Device
（1）Connect cables with the device.
（2）Push down the device into the rabbet of the steel bracket.
（3）Fix the device with screws.
Rabbet
Fixing Holes for Steel Bracket
Fixing Holes for Device
Wiring Hole
Rabbet
Steel BracketFigure（2）
Fixed DeviceFigure（4）
Fixed Steel BracketFigure（3）
Copyright © 2001-2013 Anviz Global Inc.
FacePass Pro
Quick Guide (V1.0)
Packing List
Notice
is registered trademark of Anviz Global. and cannot be used without the permission of Anviz.
Due to the consistent improving of the product, this specification and appearance is subject to change
without notice.
Standalone Facial Recognition System
Standalone Facial Recognition System
FacePass Pro
1、Please keep the product away from the magnetic field, and avoid causing any damage to the device.
2、Please don’t take apart the device or change the circuitry it.
3、Please test device connection with software before installing on the wall.
4、Please don’t install with power in order to avoid causing any damage to the device.
5、Please use the original power supply or refer to the instruction to get the right power supply.
6、Damage to the equipment caused by incorrect operation and wiring are not under warranty.
Product
1Instruction Package 2Accessory Package 3Wire 4
Copyright©2001-2013Anviz Global Inc.
FacePass Pro
Quick Guide (V1.0)
isregisteredtrademark of Anviz Global. and cannot be used without the permission of Anviz.
Duetothe consistent improving of the product, this specification and appearance is subject to change
withoutnotice.
StandaloneFacial Recognition System
StandaloneFacialRecognitionSystem
FacePassPro
COMPACT
CD-ROM
ENCH
CopyrightANVIZAllrights reserved.
http://www.anviz.com
windows
FOR
Windows98
Windows2000
WindowsXP
WindowsVista
Windows7
...
EM Card
1 2

StandaloneFacial Recognition System
FacePass Pro
StandaloneFacialRecognition System
FacePassPro
There is a button in
the Face Recognition Page.
Press it to ID Recognition
Page.
Input User ID and Password
in the input box.
ID and Password verification
succeed. The camera captures
a current image display on
the LCD.
to verify the User ID
and Password.
to cancel verification
and back to Input page.
1 2 3 4
ID Recognition
Swiped the registered card on the card redaer area.
LEDs
Power Switch
Restart
Power
Relay
NO COM NC
TCP/IP
Min USB Port
USB Flash Drive Port
Touch Screen
Dual Carmers
Card Reader Area
The Card Recognition, the
device must stay on the
Input page.
ID and Password verification
succeed. The camera captures
a current image display on
the LCD.
1 2
Card Recognition
FacePass Pro Structure
3
RFID
Notice:
The Mini USB Port use
to factory debug mode,
can not communication
with software.
Enroll User
Face Recognition
Click input box to input
Name, ID and Password.
The device provides letters
input when click “Name”
and the click to next
enroll steps.
During face image capturing process, please keep your face in the
yellow frame and move face forward and backward slightly till enrolling
successfully.
Yellow frame: The valid recognition area;
Blue frame: The valid image capturing area;
Red bar: The duration of the device in capture statues.
Green Bar: The face template capture schedule.
Power on the device
to enter Input Page.
Press to Admin
verification page.
Input default password
“12345”and press
to enter Main Menu
Page.
Click “User”option to
User Manage Page.
Click “New”to enter User
Enroll Page.
1 2 3 4
5 6 7 8
9
In the Input page ,click
to enter Face
Recognition Page.
If enable body induction
in the device, it will
automatically switch to
Face Recognition Page
when user stands in front
of the device.
According to the device
instruction ,please keep
your face in the yellow
frame.
Face verification succeed.
1 2 3 4
Press“Enroll”to capture
user face image. Before
capture user face the device
will prompt on the screen.
Press“Card”to ID card
enroll page.
Press“Read Card”, the
device waiting for swipe
card at the card reader
area. Then the Card will
display on the device.
Press back to User
Enroll Page.
Notice:
The button use to change the
camera image display on the LCD.
The button use to cancel the
face image capturing process.
3 4