Anviz M5 Plus User manual

Outdoor Fingerprint & Card
Reader/Controller
M5 Plus
Quick Guide V1.5
POWERING A SMARTER WORLD

1
Package List
RFID Card
X4
USB Quick GuideRJ45 ConnectorScrewsDevice
Notification:
1. Please check if the package contains all the items listed above. Contact
the distributor if there is any problem.
2. Please keep the product away from the magnetic field, and avoid causing
any damage to the device.
3. Please use the original power supply or refer to the instruction to get
the right power supply.
4. Please strictly follow the instructions to install the product. Any damage
to it caused by incorrect operation and wiring are not under warranty.

Illustration for placing finger
Always place finger in
the center of the sensor.
Try to place your finger covers the entire sensor.
Correct method
Incorrect method
DO NOT slide your finger
during the fingerpint
verification process.
DO NOT just use your fingertip.
DO NOT place finger
at an angle.
DO NOT place finger away from
the center of the sensor.
DO NOT move your finger before
the sensor backlight turns off.
DO NOT take off finger during
the fingerprint verification
process. 2
( Straighten your finger and then place it on the sensor Ensure the finger is flat
and covers the entire sensor)
.

Installation Diagram
Appearance
Steps: Steps:
Screw Hole
Mini USB Port
Function Button
Indicator LED
Three color: Red,
Blue and Green.
Fingerprint Sensor
Place the finger here.
3
Card Reader Area
Swipe the card here.
Step1: Drill holes in the wall
follow the hole position on
back panel.
Step2: Install and fix back
panel, connect related cables.
Step3: Place M5 Pro on back
panel, fix screw at the bottom
of M5 Pro.
Step1
Step2
Step3
Without back panel install way:Back panel install way:
64mm(2.52")
36mm(1.42")
10.5mm(0.41")
Install M5 screws directly to the
bottom shell behind the wall , the
depth of screws is 8mm(0.31"). This
install method is unique, safe and
convenient. Package list does not
include these screws,
please select matchable screws
accroding to the wall thickness.
""
"

4
Wiring Instruction
Black
Black
DC12V
GND
GND
GND
RS485A
RS485B
NO
COM
NC
Wiegand DATA0 Output
Wiegand DATA1 Output
D/S
Tamper alarm
Tamper alarm
Access Control Power Supply
Access Control Power Supply
Power off to unlock
Power on to unlock
+ 12V
GND
10
11
13
2
1
Switching Power Supply
Important notice:
Please carefully follow this wiring instruction. Any damage caused by incorrect wiring is not covered by warranty.
Switch Power
Supply
Cable Color
Function
Power
Tamper alarm
Wiegand
Output
Pulse signal
Relay Output
Description
1
2
3
4
5
6
7
8
PIN
Wiegand 0 Input/Output
Wiegand 1 Input/Output
Light brown
Brown
Pink (Thick)
Exit Button
Tamper Alarm Signal
Green
RS485B
RS485A
White
GND
DC12 V
9
10
11
Light green
Blue
Door Magnetic
NO
Light blue
Black (Thick)
Black
Red (Thick)
12
Orange
COM
NC
Connect RJ45

Switch Power
Supply
Switch Power
Supply
5
Power off to unlock
Power off to unlock
Power on to unlock
Important notice:
.
Wiring Type Access Controller
11
10
+12V
+12V
Anviz Wiegand Wiring:
SC011 and the device are paired by
Anviz wiegand to be a distributed access
control system.

4
Make sure correct wiring between M5 Plus and SC011, power on them, then move
slide switch to ‘PROGRAM MODE’ as below:
Between M5 Plus and Anviz SAC844 or other Access Controller as below:
1. Anviz Wiegand data output format:
ALL registered users output devieces’ last eight serial number.(For example, SN
of one device is 1050000014470004, then Anviz Wiegand output 14470004.)
2. Wiegand data output format:
Card user:Output card number.(Decimal)
Fingerprint user:Output ID number
3. Wiegand output format can be set by PC software
Wiegand Wiring:
SC011 authorization setting:
Switch in‘PROGRAM’on the SC011: Move slide swith to left(ON).
Wiegand data output format:
6

7
*
*
*
*Pro Proto
Function Button

IMPORTANT:
Operation Guide
Register User:
1. Swipe
Enroll Card
1Exit
Enrollment
Add One Fingerprint per User Only:
Blue LED
flashes
2. Place finger 3. Place finger
again
Blue LED flashes fast
and fingerprint
sensor lights up
Green LED lights up
with 4 short beeps,
registration successed
5. Continue to register another user
Blue LED
flashes
2. Swipe
User Card 3. Swipe User Card again
Note: 1. After finish enrolling current user,
please swipe enroll card and then continue
register another user.
2. After finish enrollment, please swipe
enroll card TWICE to exit enroll status.
Notice:
When you place finger on M5 Pro, Red LED
flashing with two long beeps means the finger has
been registered.
Add Card Only:
8
6. Swipe Enroll
Card TWICE to end
the enrollment
Notice:
When you swipe card on M5 Pro, Red LED
flashing with two long beeps means the card has
been registered.
1. Swipe
Enroll Card
Note: 1. After finish enrolling current user,
please swipe enroll card and then continue
register another user.
2. After finish enrollment, please swipe
enroll card TWICE to exit enroll status.
4. Swipe Enroll
Card once
1
6. Swipe Enroll Card
TWICE to end the
enrollment
Green LED lights up
with 4 short beeps,
registration
successed
Blue LED flashes
fast and
FingerPrint
sensor lights up
5. Continue to register another user
Exit
Enrollment
M5 Pro is suitable for DC12V power supply only. When connect to DC12V power supply, the indicator
light displays blue and flashes fast. Meanwhile, the backlights of fingerprint sensor turn on with beeps.
4. Swipe Enroll
Card once

Operation Guide
4. Continue to register the 2nd finger
Blue LED
flashes
2/5. Place the
1st/2nd finger 3/6. Place the 1st/2nd finger again
Blue LED flashes fast
and FingerPrint
sensor lights up
8. Continue to register another user
Blue LED
flashes
4. Swipe
User Card 5. Swipe User Card again
Add Two Fingerprints of one User:
Add Fingerprint and Card of one User:
2. Place finger 3. Place finger
again
9
Note: 1. After finish enrolling current user,
please swipe enroll card and then continue
register another user.
2. After finish enrollment, please swipe
enroll card TWICE to exit enroll status.1. Swipe
Enroll Card
1Exit
Enrollment
9. Swipe Enroll
Card TWICE to
end the
enrollment
Green LED lights up
with 4 short beeps,
registration
successed
1. Swipe
Enroll Card
Exit
Enrollment
9. Swipe Enroll Card
TWICE to end the
enrollment
Green LED lights up
with 4 short beeps,
registration
successed
Blue LED
flashes fast and
FingerPrint
sensor lights up
Green LED lights up
with 4 short beeps,
registration
successed
Blue LED
flashes fast and
FingerPrint
sensor lights up
8. Continue to register another user
Note:
1. After finish enrolling current user, please swipe enroll card and then continue register another user.
2. After finish enrollment, please swipe enroll card TWICE to exit enroll status.
7. Swipe Enroll
Card once
1
* Two fingerprints belongs to one user ID.
* The wiegand output of fingerprint and card are the same.
7. Swipe Enroll
Card once

* The wiegand output of fingerprint and card are the same.
Operation Guide
Delete User:
Delete Fingerprint or Fingerprint and Card
Red LED
flashes
4. Continue to delete
After delete one user, you can continue to delete
another user or swipe Delete Card to save and exit.
Blue LED
flashes
10. Continue to register another user
Add Two Fingerprints and Card of one User:
5. Swipe Delete
Card to end
the process
1. Swipe
Delete Card
4. Continue to register the 2nd finger
10
Notice:
When you place finger on M5 Pro, Red LED
flashing with long beeps means the fingerprint
does not exist in the device.
When fingerprints or card belong to one user
ID,you can delete either one to delete this
user.
7. Swipe
User Card 8. Swipe User Card again
2/5. Place finger 3/6. Place finger
again
Note: 1. After finish
enrolling current user,
please swipe enroll card
and then continue register
another user.
1. Swipe
Enroll Card
Exit
Enrollment
11. Swipe
Enroll Card
TWICE to end
the
enrollment
Green LED lights up
with 4 short beeps,
registration
successed
Blue LED
flashes fast and
FingerPrint
sensor lights up
9. Swipe
Enroll Card
once1
Green LED lights up
with 4 short beeps,
registration
successed
Blue LED
flashes fast and
FingerPrint
sensor lights up
2. After finish
enrollment, please
swipe enroll card
TWICE to exit enroll
status.
Green LED lights up
with 4 short beeps,
fingerprint deleted
Red LED flashes
fast and
FingerPrint
sensor lights up
2. Place finger 3. Place finger
again

201809
Operation Guide
After delete one user, you can continue delete another
user or swipe Delete Card to save and exit.
Delete Card:
Red LED flashes
2. Swipe
Enroll Card 3. Swipe Enroll Card again
Red LED flashes fast Green LED lights up
4 short beeps
Delete ASuccessed
Delete all uses fingerprints and cards, the
device parameter setting do not change.
Delete All Users
11
Notice:
When you swipe card on M5 Pro, Red LED
flashing with long beeps means the card does
not exist in the device.
1. Swipe
Delete Card
4. Swipe Delete
Card to end
the process
2. Swipe
User Card 3. Swipe User Card again
4. Continue to delete
1. Swipe
Delete Card
5. Swipe Delete
Card to end
the process
Red LED
flashes Green LED lights up
with 4 short beeps,
card deleted
Red LED flashes
fast and
FingerPrint
sensor lights up
Anviz brand and product are trademarked and protected under law of the United States.
Unauthorized use is prohibited.
For more information, please visit www.anviz.com , or send email to [email protected] for more help.
©2020 Anviz Global Inc. All Rights Reserved.

12
Bluetooth connection&configuration
App installation, setting & user registration:
Bluetooth connection&configuration:
1. Make sure your cell phone Bluetooth is on.
2. During the setup between app and the M5 plus, please make sure the mobile and M5
Plus are within effective distance（≦100CM)(≦39.37").
3. According to the strength of Bluetooth signal and MAC address from the Bluetooth
device which found by phone, you can check whether it’s the correct device or not.
1.Using the QR code which can get from the
Google play,
https://www.anviz.com/CrossChex.html or
manual to install the Crosschex Moblie APP
2. The interface of Mobile app will be like the
below picture when initializing.
Clicking the privacy policy,then if you choose
user option to sign in, it will show green
background colour, if you choose
administrator, it will show gray background
colour.
9:41
User
Administrator
Choose Your Role
《PrivacyPolicy 》

Click the “Get Started” Choose the proper device The app can search and match the proper device.
Default user id:0 password:12345
Input the M5 Plus device default ID and password to
identify the setting, once matching successfully, it is
working with the voice and LED reminder.
9:41
Get Started
Unlock the door with
your phone.
How it works
13
9:41
Add Device
M3 Pro
M5 Plus
M-Bio
EP300 Pro
A350
C2 Slim
SC211
9:41
M5 Plus
Turn on Bluetooth of your
smartphone. Stay near the device
within around 3ft/1m.
Start
Device List
Bunded
M5 Plus
D3:F8:64:61:84:21
9:41
User ID
Password
Login
Next
Input your ID and Password from
your administrator
9:41
M5 Plus
Setting
Done
M5 Plus
M5 Plus

Hold the circle area a
few seconds to modify
or delete device.
Choose the icon on the left top corner,
you can switch to normal user or admin
user and do the record check...
When signing in as administrator on the
app, administrator can choose one of
the available devices to finish the setup
at admin menu. Eg: user registration,
network setting, parameter etc.
Click the lock icon
to lock or unlock
14
9:41
Device List
Front Door
M5 Plus
9:41
Device List
Front Door
M5 Plus
9:41
Front Door
M5 Plus
Device List
DeleteRename
9:41
My CrossChex
My Device
Support
Language
About
User Administrator
V 2.4
Logs
9:41
Device List
Front Door
M5 Plus
9:41
My CrossChex
User
Base Info
Setting
Network

Google
CrossChex Mobile App Anviz
https://bit.ly/2Vn0wh6 https://bit.ly/2J9qA95
In order to protect the environment, Anviz has decided to go "CD Free"
campaign since June 1st 2019. We will provide QR code for you to download
the electronic documents to make sure that you understand how to install
and use Anviz devices.