Anzzi Gd-az212 User manual

Please carefully read the safety precautions before installation. This is important and must be observed.●D isconnect power before installing or servicing disposer.●C heck with aqualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded.●Al l wiring must comply with local electrical codes.●D o not reconnect electrical current at main service panel until proper grounds are installed. ●D o not position your head or body under disposer; unit could fall during removal or installation.●U se long-handled tongs or pliers to remove objects from a waste disposer.Do not put fingers or hands into a waste disposer.●To reduce the risk of injury, close supervision is required when anappliance is used near children.

IMPORTANT SAFETY INSTRUCTIONS.ICONSIGNES DE SÉCURITÉ IMPORTANTES.

PG.1●D o not put the following into a disposer: clam or oyster shells, caustic drain cleaners or similar products, glass, china, or plastic, metal (such as bottle caps, steel shot, tin cans, or utensils), hot grease or other hot liquids, paints, solvents, household cleaners and chemicals, automotive fluids, plastic wrap.●R egularly inspect disposer and plumbing fittings for water leaks,as water leaks can cause property damage. Manufacturer cannotbe held responsible for property damage as a result of water leaks.●To reduce the risk of injury and/or property damage, do not use the sink containing the disposer for purposes other than food preparation (such as baby bathing or washing hair).SAVE THESE INSTRUCTIONS,CONSERVEZ CES INSTRUCTIONS, ！

WARNING

Only connect to a Ground-Fault Circuit-Interrupter(GFCI)protected grounded socket.Do not remove the ground pin or use a ground adapter.Otherwise,electric shock will be caused by fault or short circuit.！

DANGER

WrenchSealed baffle

Lower Mounting Ring

Dishwasher Inlet

Water Outlet

Cover

oParts Included:

DisposerStopper scraperSink FlangeRubber GasketPaper GasketMetal GasketMounting Ring1 1/2" ScrewsSnap Ringss304Gasket

Flange

Discharge TubeScrews

BCDEFGHIKLMNA

Tools and Materials (not included)Plumbers putty

PG.2

15-20mm

12Loosen the three screws on the mounting assembly, get them out about 0.6 - 0.8 inch (15-20mm).Use a flat head screw to take out the snap ring (I), then separate the paper gasket (E), metal gasket (F), and mounting ring (G) from the assembly.

INSTALLATION INSTRUCTIONS

PG.3

Plumbers putty

4Take out the paper gasket (E), place the gasket (D) under the sink flange (C). Evenly apply 1/2" thick rope of plumber's putty around sink flange (C). Press it firmly onto the sink flange as shown. Remove excess putty.Place a weight, such as the disposer, on the sink flange (C) to hold it in place. Use a towel to avoid scratching sink.PG.4

56Insert paper gasket (E), metal gasket (F), and mounting ring (G). Press snap ring (I) firmly in place.Tighten the three mounting screws (H) evenly and firmly against the flange.PG.5

Slide flange (M) over discharge tube (L). lnsert gasket (K) into discharge outlet. Secure flange and discharge tube to disposer with two screws (N). Slide cover (O) over discharge tube (L) and push into the Disposer. Although the supplied discharge tube is preferred, a straight discharge tube may be used.

7！Stop and read CAUTION: DISHWASHER CONNECTION ONLY.If you do not need to connect to the dishwasher, Please skip steps 8, 9.Veuillez arrêter et lire la mise en garde :CONNEXION AU LAVE-VAISSELLE UNIQUEMENTvous n'avez pas besoin d'attacher le lave-vaisselle,Veuillez sauter les étapes 8, 9.PG.68

NOTICE: Drain plug cannot be replaced once it is knocked out.Turn disposer (A) onto side and knock out drain plug with screwdriver. Remove plug from inside of disposer with pliers.

Install dishwasher tube into dishwasher Inlet. Secure with hose clamp.179PG.7

Hang disposer by aligning 3 mounting tabs with slide-up ramps on mounting ring.Use the wrench (J) to secure the mounting ring tightly.Falling HazardRisque de chute！

WARNINGATTENTION

1011PG.8Do not position your head or body under disposer; unit could fall during removal or installation.

You may need to trim discharge tube to ensure proper fit. Make sure anti-vibration tailpipe mount is straight. Test for leaks after Installation:Place a stopper onto the flange and fill the sink with 2/3 water, turn on the disposer and then unplug the stopper to release the water.Check for leaks on positions (#1) and (#2) as showed in the picture.1213PG.9

1.Connect the disposal cord to 110-120 volt, 60 Hz AC current only.2.This waste disposal is equipped with a factory installed plug-in cordwith a three prong grounding plug. If a 110-120 volt, 60 Hz ACgrounding outlet is not available, have a proper outlet installed by aqualified electrician.3.Outlet must be installed in accordance with local electrical codes.This waste disposal requires that a dedicated switch with a marked“Off“ position. The switch shall be installed within sight of the sinkopening or the disposal.4.If the supply cord is damaged, it must be replaced by a cord assemblyavailable through Customer Service.PG.1014

Place the garbage disposal upside down. Remove the wiring cover, loosen the cable connector to make the power cord removable.

Remove the wiring cap.Remove wiring screw.Unplug the power cord.Be carefulWARNINGATTENTION

SHOCK HAZARDTurn off electric power at fuse box or circuit breaker.RISQUE DE CHOCCoupez l'alimentation électrique au niveau de la boîte à fusibles ou du disjoncteur.

ⅠⅡ

If you need to replace the power cord with yours, please read the following steps to detach it. Then install your cord by reversing steps. Please make sure your cord is American Standard SJT 16AWGX3C. Otherwise, please consult a professional electrician.

PG.11wiring cap

Operation Notes● This Disposer can deal with thefollowing garbage:- Fruit Peel- Leftovers - Fishbone- Eggshell- Other small bone●Avoid inserting the following food

waste:

- Large pieces of bones, such as the pig's leg bones.- Whole corn cob.-Shells and carapace.

-Large fruit pits.

Inserting a large bone or whole corn cob

into the disposer will cause a significant

blockage. In addition, we strongly advise

against inserting clamshells because the

crushed shell pieces can easily clog the

drainage tube.

1. turn on the tap2. turn on the air switch orremote switch

4.when you can only hear the sound of motors and water after you handled the kitchen garbage, please turn oﬀ the disposer ﬁrstly, then turn oﬀ the tap3. pour the kitchen garbage into the sink (please don't put the hard objects into the sink, such as clam, glasses, metal)

1ON2OFF43●If t he following items accidentally fall into the crushing chamber:

- Dishcloth, steel wool pad and sponge.

- Metal or wood tableware.- Glass shards and other glassware.Follow these steps to remove:- Turn oﬀ the disposer power and unplug the power cord.- Remove the objects with tongs.

If these objects get stuck and jam the

disposer, insert the hex wrench into the

center hole on the bottom of the disposer.

Work the wrench back and forth to loosen

the jam. Once you can make one complete

revolution, reach the disposer with the

tongs to remove the object. Detailed steps refer to the "User Manual" troubleshooting section.PG.12

USER-MAINTENANCE INSTRUCTIONSINSTRUCTIONS D'ENTRETIEN POUR L'UTILISATEURIMPORTANT SAFETY INSTRUCTIONSCONSIGNES DE SÉCURITÉ IMPORTANTES

●LOUD NOISES:There might be an accidental entry of a spoon, bottle cap or other object. To correct this, turn off electrical switch and water. After disposer has stopped, remove object with long handled tongs.●

UNIT STOPS WORKING:

Unplug the power cord or turn the wall

switch or breaker box switch to the "OFF"

position. Insert one end of the hex wrench

into the center hole on the bottom of the

disposer (see Figure a), work the wrench

back and forth until it runs one complete

revolution. Reach into disposer with tongs

and remove the object(s). Push the red

reset button on disposer bottom

(see Figure b).

●LEAKS: If the unit leaks at the top, it may be due to:1.Improper seating of sink flange(gasket centering, putty ortightening).2.Support ring not tightened properly.3.Defective or improperly installedcushion mount. If unit leaks at thewaste elbow, leak may be due toimproper tightening of elbow flangescrews. SAVE THESE INSTRUCTIONS. CONSERVEZ CES INSTRUCTIONS.

●DO NOT ATTEMPT TO LUBRICATE

YOUR DISPOSER!The motor is permanently lubricated. The

disposer is self-cleaning and scours its

internal parts with each use. NEVER put

lye or chemical drain cleaners into the

disposer, as they cause severe corrosion

to metal parts. The resulting damage from

such chemicals will void the warranty.

Mineral deposits from your water can form

on the stainless steel turntable, giving the

appearance of rust. PLEASE NOTE the

stainless steel turntables used will not

corrode.

abPG.13

IMPORTANT SAFETY INSTRUCTIONSThe flexible cord of a portable household disposer shall:a)Enter the enclosure through a watertight fitting or be otherwise sealedin place; andb)Be provided with strain relief that is independent of the seal, and the strainrelief means shall reduce the risk of flexing or movement of the seal. 1.1The face of a receptacle shall:a)Be flush with, or project beyond, a nonconductive surrounding surface; orb)Project not less than 0.015 in (0.38 mm) beyond a conductive surroundingsurface1.2The strain-relief means provided on the flexible cord of a disposer shall be tested as described in 1.3 During the test, the strain-relief means shall withstand for 1 min, without displacement, a direct pull of 35 lbf (156 N) applied to the cord. At the point of disconnection of the conductors, there shall not be movement of the conductors.1.3The connections within the disposer shall be disconnected. A 35-lb (15.9-kg) weight is to be suspended on the cord and supported by the disposer so that the strain-relief means is stressed from any angle that the construction of the appliance permits.SAVE THESE INSTRUCTIONS MOVING AND STORAGE INSTRUCTIONSTransportation In the course of transportation, the garbage disposals shall be protected from rain or moisture, shall avoid violent collision.Storage The packaged garbage disposals shall be stored in a warehouse with a temperature below 40℃, relative humidity below 85%, ventilated and dry, non-corrosive gas.