AOBIO D4 User manual

Telephone: [phone]
WhatsApp: [phone]
Email: [e-mail]
AOBIO D4 USER GUIDE

CONTENTS
1. Introduction ·····················································
2. Item Overview ·················································
3. Connect to PC/MAC ·········································
4. Label Setup ····················································
5. Driver Installation for MacOS & Windows ··············
6. MacOS & Windows Printing Setup ·······················
7. User Tips ························································
8. LED Status ······················································
9. Feeder Button Instructions ·································
10. Specifications ·················································
11. Safety Notices ················································
12. Maintenance ·················································
01
02
03
05
07
13
17
18
19
20
21
21

1.INTRODUCTION
Congratulations on your purchase of Aobio Printer. Aobio is
your loyal business partner offering commercial solutions to
batch labels printing.
Please take a moment to read this user guide as incorrect
operation may result in unsatisfactory print quality, reduced user
experience, or even damage to your printer or injury.
AOBIO D4 is a thermal label printer which uses thermal label media
without ink, toner and ribbon. It can print various labels for logistics,
pricing, barcodes, QR codes, shipping address, badges, etc.
Thank you for purchasing this product, please read this manual carefully before using
the printer, and keep it for future reference. If you have any questions about this
machine, please call our customer service centre on [phone].

Packing List:
2.ITEM OVERVIEW
Thermal printer head (TPH) may be very hot. Please do not
touch the printer head or parts around it after printing.
1x AOBIO Label Printer
1x Power Cable and Adapter
1x USB 2.0 to USB C Adapter
1x USB 2.0 Printer Cable
1x User Guide 1x Service Card
1x USB Stick(Contains drivers for MacOS & Windows)
2x Thermal Printer Head Cleaning Wipes
20x Free Fanfold Labels
Feeder Button
Power Switch
USB Port
Power Port
Cover
Push Button
Rubber Roller
Label Outlet
Thermal Printer Head (TPH)
Label Guide

3.CONNECT TO YOUR PC/MAC
Must turn off the switch before you plugging the power cable
into power port each time or it may cause sparks!
2.Connect the USB cable.
(Special Note: For Windows users, please connect the same USB port on your
computer to avoid producing unwanted duplicates of Aobio printer in your system).
1.Ensure the power is OFF (Press down "O" means Power OFF).

Must turn off the switch before you plugging the power cable
into power port each time or it may cause sparks!
3.Make sure the power adapter is tightly connected, then connect the power cable to
the printer’s power port and the electrical sockets.
4.Turn the power ON (Press down "-" means Power ON), now you will see the top
feeder button flashing.

Aobio is capable of working with labels in various sizes, and it needs
to learn your label properties before its first use.
Turn on the power and wait for about 5 seconds until the
printer is initialized.
1.Power On
2.Automatic Label Identification
Insert the label from the backside of the printer, the printer will
grab the label and move back and forth, then stop with the green
light on. Not a single label will be wasted during this procedure.
It's suggested to adjust the label guide to match the width of the
label if necessary before the label is pushed in.
To initiate Automatic Label Identification and run Intelligent
Label Study, please follow these steps:
4.LABEL SETUP

3.Intelligent Label Study
Press and hold the feeder button for about 3 seconds until you
hear one beep then release, the label will move back and forth
several times to study the label size, then you can start printing.
Since the printer needs to measure the length of the thermal
paper, a stack of labels with at least 3 sheets is required to
complete the process.

5.DRIVER INSTALLATION
5.1 Driver Installation for MacOS
Please download the driver for Aobio D4 from our official
website www.aobioprinter.com, or find it from the USB stick
that comes with the package.
1.Double-click the .dmg file "Aobio-Mac-Driver Latest.dmg".
Notice:
Right-click on the
PKG file and select
Open from the
pop-up menu.

2.Please right click the "AobioPrinter-Driver.pkg"file, then select
"Open"to start the installation process.
Important: Since Apple updates its security policy occasionally, double click to open
the pkg file might trigger the macOS security warning and bring up the "Unidentified
Developer" error message. If this happens, just right-click the pkg file, then click
open, and follow the instruction on the screen.
3.Click "Continue"and follow
the onscreen instructions.
4.Click "Close"to finish.