Aolait AL1019WZ User manual

19*12W MOVING HEAD BEAM
User Manual
Professional Entertainment Technology

1
Safety Instructions
WARNING
Please keep this User Guide for future consultation. If you sell the unit to another user, be
sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the unit.
Before operating, ensure that the voltage and frequency of power supply match the
power requirements of the unit.
It’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
The unit is for indoor use only. Use only in a dry location.
The unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces. Be sure that no ventilation slots are blocked.
Disconnect main power before replacement or servicing.
Make sure there are no flammable materials close to the unit while operating as it is fire
hazard.
Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but
always by taking its base.
Maximum ambient temperature is Ta: 40ɗ. DO NOT operate it where the temperature is
higher than this.
Unit surface temperature may reach up to 85ɗ. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool
down before replacing or serving.
In the event of serious operating problem, stop using the unit immediately. Never try to
repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or
malfunction. Please contact the nearest authorized technical assistance center. Always
use the same type spare parts.
DO NOT touch any wire during operation as high voltage might be causing electric shock.
Please read carefully the instruction, which includes important
information about the installation, usa
g
e and maintenance.

2
Warning:
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.
DO NOT open the unit within five minutes after switching off.
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
Caution:
There are no user serviceable parts inside the unit. DO NOT open the housing or attempt
any repairs yourself. In the unlikely event your unit may require service, please contact
your nearest dealer.
Installation:
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit
is firmly fixed to avoid vibration and slipping while operating. And make sure that the
structure to which you are attaching the unit is secure and is able to support a weight of 10
times of the unit’s weight. Also always use a safety cable that can hold 12 times of the
weight of the unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is out
of the touch of people and has no one pass by or under it.
Technical Specifications
Extrƺemely small, fast and powerful LED moving beam.
DMX Channels:ƺ16 channels mode
Operation modes: DMXƺ512, Master/Slave
Great builtƺ-in lighting shows under Master/Slave mode
Blue LCD display for easy navigationƺ
Perfect for stage, theatre, TVƺstudio, rental and discotheques
If using a 230V 50Hz power supply, DO NOT connect in series more than 11 units;
use another main supply for the next 11 fixtures.
If using a 120V 60Hz power supply, DO NOT connect in series more than 5 units;
use another main supply for the next 5 fixtures.

3
Voltage: AC 100V~240V, 50/60Hz
Power consumption: 260W
LED: 19 X 12W RGBW LED
Dimension: 324.8X188X395.4mm
Weight: 9.2Kgs
Beam Angel:
6°~50°
Control panel
Display:
To show the various menus and the selected functions
LED:
POWER ON Power On
NULL No function
NULL No function
DMX ON DMX input present
Button:
MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions

4
DMX input:
For DMX512 link, use 3-pin XLR cable to link the unit together.
DMX output:
For DMX512 link, use 3-pin XLR cable to link the unit together.
Mains input:
Connect to power supply.
Mains output:
Connect to supply power to the next unit.
Fuse(T 6.3A):
Protect the unit from damage of the over-current.
Main Function
To select any of the given functions, press the MENU button up to when the required one is
showing on the display. Select the function by ENTER button and the display will blink. Use
DOWN and UP button to change the mode. Once the required mode has been selected,
press the ENTER button to setup, to go back to the functions without any change press the
MENU button again. Hold and press the MENU button about one second or wait for one
minute to exit the menu mode.
The main functions are showing below:

5
.=OFF
Reset Default 1
.=ON
Code Code =000
PAN PAN =000
TILT TILT =000
Red Red =000
Green Green =000
Blue Blue =000
White White =000
Calibration 2
Focus Focus =000
Temperature 3 Temperature
=000C
PAN PAN =000
PAN-Fine PAN-Fine =000
TILT TILT =000
TILT-Fine TILT-Fine =000
Move Speed Move Speed =000
Dimmer Dimmer =000
Strobe Strobe =000
Red Red =000
Green Green =000
Blue Blue =000
White White =000
Special 7
Manual Control 4
Focus Focus =000
To access display Menu via the internal battery, press the UP& DOWN buttons simultaneously.
Display will automatically switch off after about 10 seconds from last button press.
LCD DISPLAY MENU
DMX Address 1
DMX Address
=001
.=Alone
Inside Program
.=Master
.=Alone
Music Control
.=Master
Auto Play 2
Slave Control Slave Run
.=OFF
Reset 3
.=ON
.=OFF
Reverse Pan 4
.=ON
.=OFF
Reverse Tilt 5
.=ON
Mic Sensitivity 6 .=000%-100%

6
LCD DISPLAY MENU
Program 01
Edit Use Program 8
Version 9 V1.0
Function Mode
DMX address setting
With this function, you can adjust the desired DMX-address via the Control Board.
Select via the encoder.
Press the encoder, adjust the DMX address by turning the encoder.
Press the encoder to confirm.
Press the Mode/Esc-button in order return to the main menu.
Set DMX address
Display the DMX 512 value of each channel
With this function you can display the DMX 512 value of each channel. The display automatically
shows the channel with a value changing.
Slave setting
With this function, you can define the device as slave.

7
Auto Play
With this function, you can run the Inside program. Music control,Slave control and Mic Sensitivity.
[Inside program]With this function,you can run the internal program.
[Music control]With this function, you can run sound-controlled.
[Slave control]With this function, you can define the device as slave.
Reset
With this function, you can reset the device via the Control Board.You can select the different reset
function by turning the encoder.
Pan Reverse
With this function you can reverse the Pan-movement.
Tilt Reverse
With this function you can reverse the Tilt-movement.
Special Setting
[Factory Reset]
With this function, you can select restore factory set for ON or OFF, the default is OFF.
[Calibrate values]
With this function, you can calibrate and adjust the effect wheels to their correct positions.
The password of calibrate values is 018.
[Temperature]
With this function, Display the temperature for Celsius or Fahrenheit.
[Manual Control]
With this function, user can control the function by manual.
Edit program
With this function,you can run the internal program. You can select the desired program under “Select
program”. You can set the number of steps under “Edit program”. You can edit the individual scenes
under “Edit scenes”. With this function, you can run the individual scenes by Channel 16.

8
Temp. Info.
Head Temp
With this function you can display the temperature on the display board of the base (near
CMY-filter)in Celsius.
No DMX Status
With this function, when the drive is not DMX signal, the display will be flashing.
Lamp adjustment
With this function, you can adjust the lamp more easily. All effects will be canceled, the shutter
opens and the dimmer intensity will be set to 100 %.With the individual functions, you can focus
the light on a flat surface (wall) and erform the fine lamp adjustment.
Users Mode
With this function, you can create user defined channel orders.
User mode set
In this menu, user can select different channels list by different sequence:
For example, after the user enter this manual, if select Auto Program = CH 22, means in this User s
mode, the Dimmer is in Channel 16.
Channel DMX Value Function
1 000 - 255 X
2000-255 XFine
3 000 - 255 Y
4 000 - 255 Y Fine
5 000 - 255 XY Speed from Max to Min
6 000 - 255 Dimmer ( 0 ~ 100% )
000 - 009 Strobe ( Close )
010 - 245 Strobe effect slow to fast
7246 - 255 Strobe ( Open )
8 000 - 255 Red ( 0 ~ 100% )
9 000 - 255 Green ( 0 ~ 100% )
10 000 - 255 Blue ( 0 ~ 100% )
11 000 - 255 White ( 0 ~ 100% )
12 000 - 255 Color Temp
Channel DMX Value Function
000 - 010 MacroColorStep (Disable)
011 - 020 R
021 - 030 G
13
031 - 040 B

9
041 - 050 W
051 - 060 R+G
061 - 070 G+B
071 - 080 B+W
081 - 090 R+B
091 - 100 G+W
101 - 110 R+W
111 - 120 R+G+B
121 - 130 R+G+W
131 - 140 G+B+W
141 - 150 R+G+B+W
151 - 255 Jump from slow to fast
000 - 010 MacroColorLine (Disable)
14 011 - 255 Slow from slow to fast
000 - 020 Empty
021 - 040 Internal program 1
041 - 060 Internal program 2
061 - 080 Internal program 3
081 - 100 Internal program 4
101 - 120 Internal program 5
121 - 140 Internal program 6
141 - 160 Internal program 7
161 - 180 Internal program 8
181 - 200 Empty
201 - 225 Motor Reset
15
15
226 - 255 Empty
16 000 - 255 Focus(0-100%)

10
Control By Universal DMX Controller
DMX 512 Connection
1.
2.
At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm
1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it
in the DMX-output of the last unit.
3.
Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to
the input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is
a very high-speed signal. Inadequate or damaged cables, soldered joints or corroded
connectors can easily distort the signal and shut down the system.
4.
The DMX output and input connectors are pass-through to maintain the DMX circuit,
when one of the units’ power is disconnected.
Each lighting unit needs to have an address set to receive the data sent by the
controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).

11
5. The end of the DMX 512 system should be terminated to reduce signal errors.
6. 3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
Address Setting
If you use a universal DMX controller to control the units, you have to set DMX address
from 1 to 512 so that the units can receive DMX signal.
Press MENU button to enter menu mode, select DMX Functions, press ENTER button to
confirm, use UP and DOWN button to select DMX Address, press ENTER button to
confirm, the present address will blink on the display, use UP and DOWN button to adjust
the address from 0 to 512, press ENTER button to store. Press MENU button back to the
last menu or let the unit idle 7 seconds to exit menu mode.
Please refer to the following diagram to address your DMX512 channel for the first 4 units˖
Channel mode Unit 1
Address
Unit 2
Address
Unit 3
Address
Unit 4
Address
16 channels 1 17 33 49