AOSEED X-MAKER User manual

User Manual

X-MAKER，让创意触手可及。
Hi, this is AOSEED X-MAKER.
X-MAKER -- Make Creativity Touchable.
X-MAKER, an AI-powered 3D printer, is a brand new product with a gamification
3D design App.Thanks to the minimalist interaction design, intelligent algorithms
and high-speed Wi-Fi data transmission, the one-touch printing feature makes this
3D printer available to everyone allowing you to create anything. The X-MAKER
does not It's not just a 3D printer, but it also includes a powerful software and rich
content, like "Things", "Theme", "Design" and "Explore" modules, which are
constantly updated. It doesn't matter if you are beginner or an advanced player,
you will always have new ways to play.

Our Product
3D Printer Instructions
Product composition
Packing list
Main components
X-MAKER App
Download
Introduction
Things / Theme / Design
Print
01
04
19
Contents
X-PRINT
Specifications
Slicing Software
Interface
Model editing
Model slicing
Model printing
25
30
Notices 31
Troubleshooting 32
Support and help 33
Power on
Welcome setup
Install the filament holder
Install the filament
Touchscreen
Load the filament
Unload the filament
Model printing
Printing complete
Remove support material
Change the filament
Move
Calibration&Leveling
Control
More settings

Our Product
X-MAKER Design App X-PRINT Slicing Software
X-MAKER 3D Printer
01
Product composition

Flexible & Magnetic
Base plate x1
U Disk x1
Quick Start x1
Power Cord x1
Tool Kit x1
Printable creative models
X-MAKER App installer
X-PRINT installer
PLA Filament x1 Filament Holder x1
3D Printer x1
Pliers x1
02
Packing list

Main components
03
Power Switch
Power Entry
Miniframe Box
Door Frame Light
Door Frame Light
Nozzle
Flexible & Magnetic
Base plate
Printing Platform
Touchscreen
USB Port
Holder Placement
Filament Inlet
Baffle
Extruder
Filament Error Sensor

Connect the power cord to the printer and the other end to
a power outlet. (Please keep your hands dry.)
Turn on the printer using the power switch
on the back.
Turn on
Connection
3D Printer Instructions
04
Power On

Select your preferred language. You can also
change it by going to "Setting -> Language".
Wi-Fi: With the same WLAN, the X-MAKER App
can be connected to the printer.
Access Point: When there is no WLAN available, the printer's
access point can provide Internet access to the application.
After power on, the welcome setup will appear on the touchscreen. Follow the steps and complete the setup.
Language Connection
Welcome setup
05

Install the holder on the right side of the printer.
Place the spoolInstall the filament holder
Place the filament spool in the holder.
(Please make sure the filaments are not knotted or crossed.)
Filament Inlet Filament Inlet
Right Wrong
Install the filament holder
06

Filament Inlet
Insert the tip into the filament inlet until the prefeeder grabs the material. Push the spring up (as shown by the red
arrow in the figure above), so that to make the filament enter smoothly.
Instructions
Note: The tip of the filament should be straightened
and cut at an oblique angle.
07
Install the filament

Print: Select the file
to print
Filament: Load / unload
Connect: Network
connection
Setting: More settings
Preheat: Nozzle/hotbed heating
and cooling
Extrusion: Load or unload
manually
Calibration: Adjust the distance
between the nozzle and base plate
Move: Adjust X/Y/Z axes
Language: Change language
Control: Switches for light
recovery, fan and power loss
Help: More information
Status: Printer status
About: Printer specifications
Homepage Setting
Touchscreen
08

Go to "Filament -> Load" and wait for the nozzle to heat up. When the nozzle reaches target temperature, the filament
will be loaded automatically. Wait for the filament to come out of the nozzle and press the [Cancel] button.
Method 1
Go to "Setting -> Preheat" and set target temperature, then select "Start" to continue. (The target temp for PLA is 200 °C,
and for ABS is 230 °C. If you use a third-party material, please refer to the target temperature on the packing box.)
Go to "Extrusion -> Load" and set the feed length to 10mm. Charging ends when the filament exits the
nozzle.
Method 2
Load the filament
09
Note: The filaments must be pushed to the end of the pipe so that it comes out of the nozzle as soon as possible.

10
Unload the filament
Go to "Filament -> Unload" and wait for the nozzle to heat up until the filament is unloaded under the extruder gear
and pull out the filament directly.
Method 1
Go to "Setting -> Preheat" and set target temperature, then select "Start" to continue. (The target temp for PLA is 200 °C,
and for ABS is 230 °C. If you use a third-party material, please refer to the target temperature on the packing box.)
Go to "Extrusion -> Unload" and set the feeding length to 10mm. Repeat the above operation for 3-5
times until the end of the material comes out towards the filament inlet. Push the spring up and pull
out the filament.
Method 2

Model printing
11
Printing interface
1. Get your pattern to cut using X-PRINT.
2. Load the file into the printer and print it with one-touch. (Make sure your printer and X-MAKER app are connected to
the same WLAN.) * Alternatively, you can save the file to a U-disk for printing with offline printers.
You can print the model by performing the following steps
Print status
Remaining time
Current Z-axis coordinate
File name
Current temperature of nozzle
Target temperature of nozzle
3D Viewer
Print progress
Stop
(Printing can't be resumed.) More settings
Current temperature of hotbed
Target temperature of hotbed
Pause/Start
(Printing can be resumed.)

Once the print job is finished, allow the baseplate to cool down for 5 minutes before reaching inside. If the print is
removed without complete cooling, some parts of the print may adhere to the baseplate. (*Don't touch the nozzle and
allow it to cool down below 45 °C to avoid burns.)
Remove the print
After removing the print, use tools to carefully clean the remaining parts of the print on the base plate. Put the base plate back on the
heating platform. (As shown in the figure below)
Place the base plate
12
Remove the print Remove support material
Printing complete
Use pliers to remove the support structures of the impression.

Some models have overhanging parts. In this case, you must print a support structure under the model to prevent
these parts from falling off. The support structures must be removed when the print is finished. You can remove the
support structures manually or using pliers.
The image on the left shows the model with the support structure.The image on the right shows the model with the
support removed.
13
Remove the support with care and do not damage the model.
Use pliers carefully, children should be under constant supervision during the process.
Model with support removed
pliers
Remove support material
Model with the support

14
Go to "Filament -> Unload" and wait for the nozzle to heat up until the filament is unloaded under the extruder gear.
Remove the filament and load a new spool of filament.
In an idle state
Go to "Pause -> Filament -> Unload" and wait for the nozzle to heat up until the filament is unloaded under the extruder
gear. Remove the filament and load a new spool of filament. Then press the [Start] button to continue the print job.
During printing
Note: Don't touch the [Stop] button by mistake, or your print job will not be able to continue.
Change the filament

15
Move
Move
To ensure optimal printing results, you need to perform the XYZ axes calibration during maintenance.
Go to "Setting -> Move -> Reset" and wait for the XYZ axes to reset. Select the moving distance: 1mm, 5mm, or 10mm.
Press the [+/-] button and move the XYZ axes. (If the distance is set to 10mm, press the [+/-] button once and the
X/Y/Z axis will move 10mm accordingly; press twice and it will move 20mm.)
Motor release
Activate this mode and you will be able to adjust the nozzle and base
plate manually. Turn off this mode and the printer will be energized
again. Only the nozzle and base plate can be adjusted using the touch
screen. (See "Move" operations for more information)
X/Y/Z axes

Calibration&Leveling
After using the X-MAKER 3D printer for a long time,the calibration should be performed to adjust the distance between
the nozzle and the base plate.
Manual leveling is required in the event that prints become warped.
1. If the distance between them is too wide, your print will not adhere properly to the base plate.
2. If the nozzle is too close to the base plate, it can prevent material from extruding.
Make sure there is no excess of material under the nozzle tip before calibrating, or you may get inaccurate results;
Place the calibration card in between the nozzle and the base plate and go to "Setting -> Calibration".The Z offset value is shown on the
touchscreen; Use the touchscreen controls to adjust the distance until you feel some resistance when moving the card. Select [Save] to
continue. (Press the [+] button once and the nozzle will be raised by 0.1mm; press the [-] button once and the nozzle will be lowered by
0.1mm.)
Click [Leveling] again and t he nozzle will move to nine points following the sequence shown in the image on the right.
Repeat the Step 3 above for each point and adjust the distance between the nozzle and the base plate until you feel some resistance
when moving the card. Click the [Complete] button and the calibration is finished!
Calibration
Leveling
Note: Calibration is a professional operation. Usually, there is no need to perform manual calibration. The distance has been set before printers
leave the factory. It is recommended to adjust the offset value in the range from -0.5mm to 0.5mm.
16
Leveling sequence

Control
Internal: Control the lights inside
External: Control the external lights
Fan: Control the fans to cool down
ES Mode: Low the temperature inside for optimal printing results
Child Lock: Prevent the print stop or other problems caused by
children's mistaken touching
Power Loss Recovery: Proceed with the print job after a power failure
FES: Pause the print job automatically and prompt you to change the
filament when the filament runs out.
Control
CONTROL includes switches for internal light, external light, fan, ES mode, child lock, power loss recovery and
filament error sensor.
* It is not recommended to turn off the fan.
17