Apache AL13P User manual
AL13P Laminator Operation Manual
Product Overview:
Thank you for your Apache purchase. All Apache products are designed to provide excellent
function, high quality, ease of use and stylish appearance. The Apache AL13P laminator is an A3
class laminator which is capable of laminating items up to 13" wide, specifically standard 8 ½ x
11” sheet of paper sideways for quicker lamination. The AL13P is a professional grade laminator
which is designed with heavy duty steel, professional grade heating elements and motor, and
has 4 silicone rollers. Additionally, the AL13P has the ability to laminate in cold mode. The
AL13P is designed for long term, heavy duty use. This laminator can help protect documents and
photos from wear, tear, liquids, and humidity, along with preserve and enhance presentation
documents.
Key Features:
•4 Silicone Rollers
•Heavy Duty Steel Case
•Professional Grade Motor and Heating Element
•Variable Temperature Control From 77 – 390.2⁰F (25 - 200⁰C) (adjustable)
•13" Laminating Width
•Forward and Reverse Switch
•Cold Laminating Mode
Specifications:
Model:
AL13P
Power:
600W
Voltage:
110-120V AC, 2.4A @ 60Hz
Speed:
2.5pp/min
Working Temperature
Range:
77⁰F (25⁰C) – 390.2⁰F (200⁰C)
(adjustable)
Maximum Pouch
Thickness:
10 mil Max
Pre-Heat Time:
3 minutes
Certifications:
ISO9001 Designation
Warranty:
1 Year through Manufacturer
Dimensions:
W 19 11/16" x D 8 1/8" x
H 4 3/8"
Weight:
13lbs
Operation Instructions:
1. Plug in the power and turn on the power switch located at the rear of the unit.
2. The lowest heated temperature setting is 212⁰F (100⁰C). The temperature setting can be
raised or lowered based on the type and thickness of the lamination pouches. Initially
start with a lower temperature, the high heat of the machine can cause the laminating
sheet to melt and clog the machine.
3. Preheat time is approximately 3 minutes, while the unit is preheating the LED will be off.
Once preheated, the ready light will turn green, and laminating can begin.
4. Place the item to be laminated in a laminating pouch. Insert laminating pouch, pre-
sealed end first into the laminating machine. Be sure to align item properly. Once
inserted the rollers will start the laminating process. A carrier is not needed for most
pouches, but if desired a carrier or a piece of paper on top of the pouch may be used.
5. If the item is inserted incorrectly, reverse the rollers to back the item out of the
machine. To do so simply press the “REV” button to back the item out. Press the “REV”
button again to return to normal mode.
6. Again, adjust the laminating temperature based on the thickness of the pouch. If
unfamiliar with the pouches, start with a lower temperature and slowly increase until
the appropriate temperature is reached. If laminated item is cloudy, raise the heat on
the unit then run the item through the machine again.
mil
mm
(millimeters)
mic
(microns)
Temperature
Setting
1.49
0.038
38
230⁰F (110⁰C)
2.95
0.075
75
277⁰F (130⁰C)
4.92
0.125
125
302⁰F (150⁰C)
9.48
0.25
250
356⁰F (180⁰C)
Cold Laminating:
This laminator has the ability to be used for cold lamination processes. To use for cold
lamination simply set the machine to room temperature, open the top cover and proceed with
the lamination process.
ATTENTION:
Monitor the laminator at all times when the machine is turned on. DO NOT LEAVE
UNATTENDED. This laminator’s adjustable heat means it can reach higher temperatures than
some other laminators. Always start with lower temperature settings and gradually increase the
temperature as needed. Use extra caution when using high temperatures. Please operate in an
open, dry place away from temperature sensitive materials. Do not place anything on or near
machine when in operation. After laminating please set machine to minimum temperature and
allow to run for 2 minutes so rollers can cool. Always unplug unit before servicing. To clean
rollers use laminator roller cleaner pads available at office supply stores. Please follow
instructions included with cleaner pads. The Limited Liability Warranty applies to laminator only.
Apache Laminators is not responsible for damage to any other personal property.
TROUBLESHOOTING:
If you experience issues, many times the laminator is either too hot or too cold. Ensure the
laminator heats up completely before using it and use a carrier or sheet of paper on top only
when necessary. If the document does not seal or bubbles form, the laminator is too cold. Run
the pouch through a second time or turn up the temperature. If waves or warping occur, the
laminator is too hot. Add a cover sheet or turn the temperature down. If the temperature is
adjusted, always wait approximately 3-5 minutes before continuing.
CONTACT INFORMATION:
The AL13P comes with a 1 Year Manufacture’s Warrantee that does not require registration. If
you experience any issues please contact us at the phone number or email listed below.
Need technical assistance or have a question? Contact us by phone at 1-866-602-7742 or by
assist you.
Thank You,
The Apache Team
www.apachelaminators.com
Revision Date: 9/14
© 2014 Apache Laminators
Table of contents
Other Apache Laminator manuals
