D&K Masterpiece 550 User manual

CONTENTS
•Fast Operation: Superior heating system quickly brings
the platen to uniform temperature ensuring 100%
bonding.
•Extended Temperature Range: Thermostat control
adjusts from 100º F to 300º F (38 º –150º C) to cover a
wide range of operating temperatures.
•Programmed Heating Cycles: Temperature and time may
be set by stored programs in control unit.
•TemperatureReadout: Platen temperatureis indicated
on LED display on top of unit.
•Cycle Time Readout: Remaining time in the cycle is
displayed.
•Oversize Capacity: Design allows processing of materials
larger than the press platen by sliding the work side-to-
side or out the front or back of the press.
•Extra-Wide Opening: Opens a full 9” (23cm) for 550
and 10” (25cm) for 250 to provide easy access to
platen surface.
•Easy Pressure Adjustment: Pressure adjusts and locks
in seconds to accept materials up to 1" (25mm) thick.
•Non-Stick Surface: Platen surface is specially coated to
help keep adhesives from sticking.
•Free-Floating Platen: Seats evenly on the work without
shifting to provide uniformpressureacross the entire
surface.
•Rugged Construction: Steel cantilevers increase
durability and allow maximum pressureon work
within the press. Metal top and base construction
adds ruggedness.
PRESS FEATURES AND SPECIFICATIONS
2
Press Features and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Identification of Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation and Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Program Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Procedures For Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Processing Oversize Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pressure Adjustment Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

WIRING DIAGRAM
8
*Masterpiece 550 International only

TROUBLESHOOTING GUIDE
10