Apex Digital MT-FPN4060UV User manual

MT-FPN4060/6090

Description

23.6”x15.7”(60x40cm) /
/ K C M Y K C M Y / K C M Y W W V V
233.7lb /
51.2”x31.4”x21.7”(60x40cm) /
1.White Ink Stirring System
2.Ink Bottles
3.UV LED power Connector
4.UV LED Signal Cable
5.Connectors for Cooling
Liquid Tube
6.Intake Fan
7.General Power Connector
8.General Power Switch
9.Label

BI-D+:Real-time Bi-direction standard.
If there is ghosting during printing, you
could adjust there. Push the button and
turn left to adjust the printing quality.
Check the printing is normal or not, if not,
push the BI-D-to adjust.
BI-D-:Real-time Bi-direction
FEED+: Real-time Stepping standard.
If there is ghosting during printing, you
could adjust there. Push the button and
turn left to adjust the printing quality.
Check the printing is normal or not,
if not, push the FEED- to adjust.
FEED-： Real-time Stepping
Test: Push it once, printer head
will do a nozzle test and then it
back to the home position
automatically.
Pause: Push this button, the
printing will be paused. Push
it again, it will continue to
print.
Cancel: Cancel the printing job during printing.
Cleaning: Push the cleaning button
will start auto cleaning.

Description

Description

3.4.1 Menu column description
File
(1). Open: PrintMon supports. prn or. prt formats,
or Photoprint software Send task directly.
(2). Config Manager: supports export and import of files.
Used for configuration backup and recovery.
(3).Quit :Exit from software during software not used.
Job
(1). Motor Reset: To reset cartridge. The cartridge is automatically
return to standby status.
(same function with Enter on the control panel)
(2). Clean PrintHeads : clean head during printing standby or finished.
(same function with Enter on the control panel)
(3). Print:Start printing.
(4). Stop : Stop the printing task and the cartridge will be returned to
origin.
(same function with Enter on the control panel)
(5). Pause:Pause printing and recover unfinished task by Resume.
(same function with Enter on the control panel)
(6). Resume : after press Pause, recover the printing task.
(same function with Enter on the control panel)
(7). Delete : Delete the printing task.
(8). Fedd+:Add the steps during printing. (Unit: DPI)
(9). Fedd-:Reduce the steps during printing.(Unit: DPI)
Setting
(1). Setting: Configure for network printing parameters. Used to set
port, buffer path, inks amount. If choose “Adjust ink am out and
printing area before printing”, the dialog box from PrintMon task
to choose inks amount.
Description

(2).UV lamp setting : Used to set the UV lighting
position.
(3).Spot Colors Setting: Used to set the white ink spraying
position, white ink printing model, white ink channels
and amount.
1> Spot mode: White in-line,choose spot mode and un
der colors;
2> White ink channel: choose 5,6,7and8;
3> Channel ink volume:
① print only white : no color;
② print only color : no white;
③ Chnl:if choose close to print ,this channel is close
down, if choose is 200% to print, this channel is
taking double ink(chnl 5678 is printing times of the
white ink).
(4).Ink Fill: Suck ink (same function with manual clean button)
Start: Start suck;
Finish: Finish suck;
Close: Close this window.
(5).Auto Clean Stack Setting:
1> Clean: choose clean mode, the clean model of each
machine is corresponded to the type of cleaning
structure, it cannot be modified.
This machine choose auto scraping piece&
push-and-pull stack;
2> Cleaner: Clean Movement settings are default
please do not change them.
Description

Test:
(1). Scan Motor Test: The cartridge will automatically
execute test when test starts. If the machine
jumps is strictly and the head will hit the origin,
the test will be automatically stopped and the
cartridge will automatically return to origin.
(2). Total Length Test: Used to test the machine
length to avoid the head hit and also measure
the wheels contrast.
(3). Feed Adjust Test: The right figure is the steps
tests configuration page:
Rough Adjustment: Click to do test of vertical
motor movement 100mm to check the actual
position is correct. If incorrect, change Move
Distance and recalculate the wheels contrast.
Fine Adjustment: click Print vert adjust Picture,
if 0 position is not aligned, change Vert adjust
value and recalculate the wheels contrast.
See previous description about the menu column.
Test: do printing test. If there is break lines, do adjustment;
H. Align; Print horizontal calibration figure. If the line is not straight and aligned,
readjust the head horizontal position.
3.4.2 Tools menu description
Description

Feed: Print the vertical steps figure to calibrate
the vertical steps alignment.
Feed+、Feed-：Execute real-time
steps calibration. Do not change this value randomly.
Bi-D+、Bi-D-: Real-time bi-direction calibration.
SamClr, DiffClr: No need for adjustment;
Bi-D:Print bi-direction calibration figure to calibrate the alignment distance.
(1) Horz Begin :The horizon start printing position;
(2) Vert begin :The forward movement distance before
printing;
(3)X Speed Y speed: fast by default;
(4)You can choose uni-direcotion and bi-direction
option, eclosion model;(The printing speed of Bi mode is
one time faster than uni mode, but the quality of uni
printing will be better)
(5)Set whether the platform moves forward or backward
and movement distance after printing.
(6)Color Bar Setting :Whether add the color bars;
(7)Flash jet settings： off by default;
(8)Color: Used to choose the channel start, close and
orderparameters.
please set white channel as LC*4,if a color channel
does not work, close the channel and select a good
white channel to replace it.
12
3
4
5
6
7
8
3.4.3 Set the printing parameters
Description

(1). Status column: in the below of main window to display the board working time limits, send pulse
amount, feedback pulse amount ,flash status, scan speed, inkjet frequency, USB types
(USB3.0 for this machine)
(2). Job column: including files name, status, printing speed(size),copies,Pass number and
remaining time.
(3). Preview
Print task display, preview figure, printing task size and printing precision and task preview.
3.4.4 Software display
Description