Applied Wireless KTXW24SSA1 User manual
1
User’s Guide
Instructions for Installation and Operation
2.4 GHZ SPREAD SPECTRUM REMOTE CONTROLS
Handheld Transmitter
Model KTXW24SSA1
KTXW24SSA2
KTXW24SSA4
KTXW24SSA6
KTXW24SSA12
Remote Control Receiver w/Relays
Model RCR24SSA-6R
Long Range Wireless Applications 2
This page intentionally left blank.
3
Applied Wireless Inc.
Remote Control Transmitters
Models KTXW24SSA1,-2,-4,-6, KTX24SSA12
Remote Control Receiver
Models RCR24SSA-6R
Product Descriptions
These remote control receivers and transmitters are designed to provide a quick
and cost effective solution for a variety of wireless remote control applications.
The receiver utilizes Spread Spectrum technology and offers excellent
electromagnetic interference (EMI) tolerance - often found in AC and DC motor
applications. The receiver includes three low voltage, internal, 10-Amp, SPDT
relays and an external whip antenna. Expected range with these products is 350
to 500 feet*. The range may be increased through the use of a higher gain
antenna (800253-5-RC) at the receiver. These products will not interfere with or
be affected by Wi-Fi systems.
The receiver runs on 12 to 24 Volts AC or DC (supply not included).
Through the use of jumper settings on the receiver board, the receiver can be
operated in momentary, latched (one button on, another button off), or toggle
modes. It can be configured to operate as channels 1 through 6 (default) or
channels 7 to 12.
The receiver can quickly “learn” up to 60 Applied Wireless transmitters with
different address codes. All keyfob transmitters come from the factory with a
unique ID code. A receiver will only respond to the transmitter whose ID code
has been “learned”. All other transmissions from transmitters with different ID
codes will be ignored. Multiple transmitters and receivers may be used in the
same area without interfering with each other.
Power for the 6-button handheld is supplied by a 3V CR123 battery (included).
Power for the 12-button handheld transmitter is supplied by two AA batteries. An
indicator LED indicates the transmitter is transmitting.
* Unobstructed, straight line-of-sight range, when used with the standard
antennas included with the receiver.
4
Installation Instructions
Before Beginning the Installation
Plan your installation carefully. The physical location and orientation of the
receiver will have a significant influence on reception, particularly at longest
ranges. For best results, the receiver antenna, should be positioned
vertically (pointing either up or down). If necessary, use double-sided foam
tape or hook & loop fasteners (not supplied) to secure the transmitter to a non-
metallic vertical surface. Also, keep in mind that the RF signal from the
transmitter will travel through most non-metallic building materials (wood, stucco,
brick, etc.), however maximum stated reception range is based on unobstructed
line of sight conditions.
Keyfob Button / Relay Assignment
Relays in the receivers respond to the buttons on the transmitters as follows:
Transmitter
Type
Transmitter
Button Numbe
r
Corresponding Relay in
RCR24SS
A
-6R or -12R Receive
r
Six-Button
KTX
1 Rela
y
#1
2 Rela
y
#2
3 Rela
y
#3
4 Rela
y
#4
5 Rela
y
#5
6 Rela
y
#6
Twelve-Button
KTX
1 Rela
y
#1
2 Rela
y
#2
3 Rela
y
#3
4 Rela
y
#4
5 Rela
y
#5
6 Rela
y
#6
7 Rela
y
#7
8 Rela
y
#8
9 Rela
y
#9
10 Rela
y
#10
11 Rela
y
#11
12 Rela
y
#12
5
RCR24SSA-6R Programming and Configuration
Transmitter Learn Mode
The receiver will learn up to 4 transmitter IDs, storing the IDs in non-volatile flash
memory. To learn a transmitter, perform the following steps:
1. Power up the receiver.
2. Remove the receiver antenna.
3. Momentarily press the LEARN button. The LEARN LED will illuminate.
4. Press any button on the transmitter. When the LEARN LED turns off,
the transmitter has been learned.
5. To learn another transmitter, repeat steps 3 and 4.
When a fifth transmitter is learned, the first (oldest) transmitter that was learned
is eliminated from the receiver’s memory and will thus no longer operate the
system. Similarly, if the Learn Mode procedure is performed four times with the
same transmitter, all previously learned transmitters (with different IDs) will be
erased from the receiver’s memory and will no longer operate the system.
Relay Response Mode Configuration (DIP Switch S1)
Each of the six relays of the 6-channel remote control receiver may be configured
for one of three possible “Response Modes.” A Response Mode defines how a
relay functions when that relay’s associated button is pressed on the handheld
transmitter (part number KTXWSSA6). The individual Response Modes for Relay
1 through Relay 6 are determined by the settings of DIP Switches S1-1 through
S1-6 respectively, as shown in Fig. 1. The three available Response Modes are
Momentary (factory default), Toggle, and Latched. The following sections
describe in detail the characteristics of, and configuration settings for, the various
Relay Response Modes.
S3
S3-1
S3-2
S3-3
S3-4
S3-1 ,S3-2 S3-3
S3-4
6
Momentary Mode (factory-default)
A relay energizes when its associated button on the transmitter is pressed. The
relay deactivates when the transmitter’s button is released (or reception of the
transmitter’s signal ceases). A relay is configured for Momentary Mode when that
relay’s associated section of DIP Switch S1 is set to the center (MOM) position.
Toggle Mode
A relay energizes when its associated button on the transmitter is pressed, and
remains energized after the button is released. A subsequent press of the same
button on the transmitter will deactivate the relay. In this mode, each of the relays
is completely independent of the others, thus any number of relays configured for
Toggle Mode may be energized at any given time. A relay is configured for
Toggle Mode when that relay’s associated section of DIP Switch S1 is switched
down to the TOG position.
Latched Mode
The following applies to only those buttons where S1 setting is set to LATCHED
mode. Otherwise they will be TOGGLE or MOMENTARY as set by S1.
(DIP Switch S3)
A relay energizes when its associated button on the transmitter is pressed, and
remains energized after the button is released. That relay is turned off when
another Latched Mode relay is activated. A relay is configured for Latched Mode
when that relay’s associated section of DIP Switch S1 is switched up to the
LATCH position. If any relays are configured for Latched Mode, a “Latch Group”
must also be selected via DIP Switch S3 (refer to Fig. 1). A Latch Group consists
of two or more relays. Only one relay within a Latch Group can be energized at
any given time. The receiver offers four different Latch Groups: Horizontal,
Vertical, Corner, and Global. Each Latch Group is organized by the physical
orientation of the buttons on the handheld transmitter, as shown in the following
four illustrations. The desired Latch Group may be selected via DIP Switch S3
(refer to Fig. 1).
7
LATCH GROUPING OPTIONS
S3-1
S3-2
S3-3
S3-1
8
Master Reset Function (optional)
In addition to the Latch Groups described above, the 6-channel receiver provides
an optional Master Reset function. If the Master Reset function is enabled,
pressing Button 6 on the transmitter will turn off any relay(s) that is(are)
energized (either latched or toggled) at that time. When the Master Reset
function is enabled, Relay 6 is nonfunctional (does not respond to Button 6 on
the transmitter), regardless of the Response Mode to which it is configured (via
DIP Switch S1-6). The Master Reset function is enabled by setting DIP Switch
S3-4 to its ON position.
Miscellaneous Considerations for Configuration
• When changing any DIP Switch settings, the receiver MUST be disconnected
from power. Configuration changes do not take effect until the receiver is
powered up (i.e. the DIP Switches are only interrogated by the receiver’s
microprocessor at power-up initialization).
• DIP Switch S1-7 and S1-8 are not used. They are reserved for future product
enhancements.
• For DIP Switches S3-1, S3-2, and S3-3 only the highest-numbered switch is
recognized if more than one is turned on. This does not apply to S3-4 (Master
Reset).
LED Indicators (Receiver)
Power LED: Indicates that voltage is applied to the receiver.
Relay LED’s (6): They indicate for each relay whether the relay is activated.
Learn LED: Indicates when “Learn” mode is activated.
Controlling 120V Circuits and High Amperage Loads
The RCR receiver is not UL listed, and 110 or higher voltage circuits should not
be directly connected to the receiver relays. These circuits can be controlled
however by using a contactor with a 24-VAC coil (AW PN 269006, 25A
contactor).
For low voltage loads over 10 Amps, Applied Wireless offers internal 16A relay
option or high current relays (AWPN 269007, 30A 12VDC Relay) that can be
controlled by the RCR receiver.
9
RCR24SSA-6R Programming and Configuration
Frequency Setting (DIP Switch S2)
It is recommended that you do not change this setting unless needed.
In order for more than one system to operate in the same area, up to 16 different
frequency settings are available. Remove the lid from the case of the RCR24SS-
6R receiver. S2 is a 4 position dip switch which is near the edge of the board and
can be set to up to 16 unique patterns that correspond to 16 different frequency
settings. The pattern set in the receiver frequency switch has to match the
pattern set in the transmitter frequency switch, which is also a 4 position dip
switch exposed when the case is taken apart.
Bank Switch Setting
To allow 2ea RCR24SS-6R receivers to be used with 12 channel transmitters an
internal jumper setting is available. When the lid is removed from the case of the
RCR24SS-6R receiver, a jumper setting near relay K5 in the 6 channel receiver
is a 3 position header with a jumper installed. If the jumper is installed between
the center pin and the pin marked “A” then the 6 relays will respond to Buttons 1
thru 6. If the jumper is moved to between the center pin and the pin marked “B”
then the relays will respond to Buttons 7 thru 12.
10
Board Switch & Jumper Locations
11
RCR24SSA-6R Receiver Block Diagram
+12 V
-
+
MOMENT A R Y T OGGLE
AND
L AT CHI NG LOGIC
RX2 4 SSA
SUPERHET
RECEI VER/
DECODER
REG
LEARN
+12 V
+12 V
+12 V
+12 V
+12 V
+12 V
ANTENNA
+12 TO 24 V
AC/ DC
NC1
C1
NO1
NC2
C2
NO2
NC3
C3
NO3
NC4
C4
NO4
NC5
C5
NO5
NC6
C6
NO6
12
RCR24SSA-6R Receiver Package Information
6.50 6.00
3.85
O
.190
4.35
1.3 6
1.4 2
4.00
ANT E NNA
POWER
DATA
LEARN LED
REL AY 6
RELAY 5
RELAY 4
REL AY 3
REL AY 2
REL AY 1
LEARN SWITCH
12-24V AC/DC
REL AY 1
REL AY 2
REL AY 3
REL AY 4
REL AY 5
REL AY 6
NC6
C6
NO6
NC5
C5
N0 5
NC4
C4
N0 4
NC3
C3
N0 3
NC2
C2
N0 2
NC1
C1
N0 1
1.2 3 9
1.2 3 9
NC-Normally Closed Contact
Cx- Common Contact
NO- Normally Open Contact-
Terminal Strips may be “unplugged” for ease of installation.
13
RCR24SSA-12R Receiver Block Diagram
+12 V
-
+
MOME N T ARY T O GGL E
AND
L AT CHI NG L OGI C
RX2 4 SS A
SUPERHET
RECEI VER/
DECODER
REG
LEARN
+12 V
+12 V
+12 V
+12 V
+12 V
+12 V
ANTENNA
+12 TO 24 V
AC/ DC
NC1
C1
NO1
NC2
C2
NO2
NC3
C3
NO3
NC4
C4
NO4
NC5
C5
NO5
NC6
C6
NO6
+12 V
-
+
MOME N T ARY T OGGL E
AND
L AT CHI NG L OGI C
REG
+12 V
+12 V
+12 V
+12 V
+12 V
+12 V
+12 TO 24 V
AC/ DC
NC1
C1
NO1
NC2
C2
NO2
NC3
C3
NO3
NC4
C4
NO4
NC5
C5
NO5
NC6
C6
NO6
14
Ordering Information
Frequency
(MHz)
Model
Number
6-Button Watertight
Transmitter 12-Button
Transmitter
2400-
2483
RCR24SSA-6R KTXW24SSA2, -4, -6
RCR24SSA-6R1 KTX24SSA12
Receiver Electrical Characteristics
Paramete
r
Min Typ Max Unit
Operating Voltage Range (AC or DC) 10 12 26 Volts
Operating Current, Un-Activated 20 25 mA
Operating Current, Activated 50 60 mA
Relay Contact Ratings @ 28VDC 10 A
Center Frequency 2400-2483 MHz
Antenna Input Impedance Ω 50 Ohms
Operating Temperature -20 +60
C
Number of Address Codes Possible 4.2 Billion
KTXW24SSA2, -4, -6 Transmitter
Battery: one CR123A coin cell
Size: 3.40 x 2.56 x 1.10 inches (86 x 65 x 28 mm)
KTXW24SSA12 Transmitter
Battery: two 1.5 VDC, type AA
Size: 5.74 x 1.82 x 1.31 inches 146 x 46 x 33 mm)
FCC ID: UY124
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference and (2) This device must accept
any interference received, including interference that may cause undesired
operation.
Related Products
AW Part Numbe
r
Description
800253A-3-RC Antenna, Rubber Duck, 3dBi, 110mm, Swivel, RPSMA
(
included
)
800253
A
-5-RC
A
ntenna, Rubber Duck, 5dBi, 190mm, Swivel, RPSM
A
610307
A
C Power Adapter, 120VAC -12VDC, 200m
A
610300
A
C Power Transformer, 120VAC-24VAC, 20V
A
800216
A
C Power Adapter, 120VAC-12VDC, 500m
A
269006
A
C Power Line Contactor, SPST, 25
A
, 24VAC coil
610347
A
C Power Adapter, 120VAC-24VDC, 0.8
A
1 Set Channel group jumper to 7-12.
15
Application Circuit – DC Motor Forward/Reverse Circuit
This is an example of using the RCR24SSA-6R Receiver for wireless
forward and reverse remote control of a DC motor. The wiring diagram shows the
motor connected to Relays 1 and 2. Thus it follows that Buttons 1 and 2 on the
handheld transmitter would control the motor (e.g. Button 1 for forward, Button 2
for reverse). With Relays 1 and 2 configured for Momentary Mode (factory
default), the motor runs in the desired direction only when the appropriate button
on the transmitter is pressed. When the button is released, the motor stops.
If the motor is equipped with limit switches, Relays 1, 2, and 3 could be
configured for Latched Mode. In this configuration, a momentary press of Button
1 or 2 would cause the motor to run continuously in the appropriate direction,
until it reaches the limit switch. Button 3 can be used to stop the motor at any
time (Relay 3 would not be connected to anything).
RECEIVER
16
For Models:KTXW24SSAnandHTXW24SSAnwheren=numberofchannels:
FCCID:UY124
“This device complies with Part 15 of the FCC Rules. Operationissubjecttothe
followingtwoconditions:(1)thisdevicemaynotcauseharmfulinterference,and(2)
thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycause
undesiredoperation.”
INSTRUCTIONTOTHEUSER
Note:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassB
digitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovide
reasonable protection against harmful interference in a residential installation. This
equipmentgenerates,usesandcanradiateradiofrequencyenergyand,ifnotinstalled
andusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradio
communications. However, there is no guarantee that interferencewillnotoccurina
particular installation. If this equipment does cause harmful interference to radio or
televisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,the
user is encouraged to try to correct the interference by one ormoreofthefollowing
measures:
—Connect the equipment into an outlet on a circuit different from that to
whichthereceiverisconnected.
—Consultanexperiencedradio/TVtechnicianforhelp.
‐‐‐Reorientorrelocatethereceivingantenna.
‐‐‐Increasetheseparationbetweentheequipmentandreceiver.
ChangesormodificationsnotexpresslyapprovedbyAppliedWirelesscouldvoidthe
user'sauthoritytooperatetheequipment.
ONE YEAR LIMITED WARRANTY (USA)
Products manufactured by APPLIED
WIRELESS, INC. (AW) and sold to purchasers
in the USA are warranted by AW according to
the following terms and conditions. You should
read this Warranty thoroughly.
WHAT IS COVERED, AND DURATION OF
COVERAGE:
AW warrants the product to be free from
defects in materials and workmanship for one
(1) year from the date of purchase by the
original end user purchaser.
WHAT IS NOT COVERED:
This warranty does not apply to the following:
1. Damage caused by accident, physical or
electrical misuse or abuse, improper
installation, failure to follow instructions
contained in the User’s Guide, any use
contrary to the product’s intended
function, unauthorized service or alteration
(i.e. service or alteration by anyone other
than AW).
2. Damage occurring during shipment.
3. Damage caused by acts of God, including
without limitation: earthquake, fire, flood,
storms, or other acts of nature.
4. Damage or malfunction caused by the
intrusion of moisture or other
contamination within the product.
5. Batteries supplied by AW in or for the
product.
17
6. Cosmetic deterioration of chassis, cases,
or pushbuttons resulting from wear and
tear typical of normal use.
7. Any cost or expense related to trouble-
shooting to determine whether a
malfunction is due to a defect in the
product itself, in the installation, or any
combination thereof.
8. Any cost or expense related to repairing or
correcting the installation of an AW
product.
9. Any cost or expense related to the
removal or reinstallation of the product.
10. Any product whose serial number or date
code is altered, defaced, obliterated,
destroyed, or removed.
This warranty is extended to the original
purchaser of the product(s) only, and is not
transferable to any subsequent owner or
owners of the product(s). AW reserves the right
to make changes or improvements in its
products without incurring any obligation to
similarly alter products previously purchased.
EXCLUSION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES:
AW expressly disclaims liability for incidental
and consequential damages caused (or
allegedly caused) by the product. The term
“incidental or consequential damages” refers
(but is not limited) to:
1. Expenses of transporting the product to
AW to obtain service.
2. Loss of use of the product.
3. Loss of the original purchaser’s time.
LIMITATION OF IMPLIED WARRANTIES:
This warranty limits AW’s liability to the repair
or replacement of the product. AW makes no
express warranty of merchantability or fitness
for use. Any implied warranties, including
fitness for use and merchantability, are limited
in duration to the period of the one (1) year
express limited warranty set forth herein. The
remedies provided under this warranty are
exclusive and in lieu of all others. AW neither
assumes nor authorizes any person or
organization to make any warranties or assume
any liability in connection with the sale,
installation, or use of this product.
Some states do not allow limitations on how
long an implied warranty lasts, and some states
do not allow the exclusion or limitation of
liability for incidental or consequential damages
so the limitations or exclusions stated herein
may not apply to you. This warranty gives you
specific legal rights and you may have other
rights which vary from state to state.
(continued on next page)
18
ONE YEAR LIMITED WARRANTY (USA), cont.
HOW TO OBTAIN WARRANTY SERVICE:
If a product covered by this warranty and sold in the USA by AW proves to be defective during the
warranty period AW will, at its sole option, repair it or replace it with a comparable new or
reconditioned product without charge for parts and labor, when said product is returned in compliance
with the following requirements:
1. You must first contact AW at the following address/phone for assistance:
APPLIED WIRELESS, INC.
1250 Avenida Acaso, Suite F
Camarillo, CA 93012
Phone: (805) 383-9600
If you are instructed to return your product directly to the factory, a Return Merchandise
Authorization number (RMA) will be issued to you.
2. You must package the product carefully and ship it insured and prepaid. The RMA number must
be clearly indicated on the outside of the shipping container. Any product returned without an
RMA number will be refused delivery.
3. In order for AW to perform service under warranty, you must include the following:
(a) Your name, return shipping address (not a PO Box), and daytime telephone number.
(b) Proof of purchase showing the date of purchase.
(c) A detailed description of the defect or problem.
Upon completion of service, AW will ship the product to the specified return shipping address. The
method of shipping shall be at AW’s sole discretion. The cost of return shipping (within USA) shall be
borne by AW.
19
Troubleshooting Guide
Symptom Possible Problem Notes
Poor Range Antenna Receiver Antenna connected,
vertically oriented and placed
preferably at least 7' high and
away from metal surfaces.
Antenna will not work inside a
metal box
RF Interference Check equipment operation at
a different location.
Battery If the remote transmitter has an
indicator LED, does it light
brightly when button is
pressed? If not, replace
battery.
Doesn't Work Power Check power to receiver
(power LED lit?)
Relay Connection Verify connected to the correct
Relay.
ID Code Match Re-"Learn" remote to receiver.
MUST BE DONE WITH
ANTENNA REMOVED.
Re-Boot Needed Remove power from receiver
for at least 5 seconds.
20
Applied Wireless products are designed and manufactured
with pride in the United States of America
Copyright 2014 by Applied Wireless, Inc. All rights reserved.
Specifications subject to change without notice.
APPLIED WIRELESS, INC.
1250 Avenida Acaso, Suite F, Camarillo, CA 93012
Phone: 805-383-9600 Fax: 805-383-9001
Email: [email protected]
www.appliedwireless.com
Pub. # UG-RCR24SSA Rev. Date 3/15
Other manuals for KTXW24SSA1
1
This manual suits for next models
5
Table of contents
Other Applied Wireless Remote Control manuals
