Savant WP3-0002-00 Series User manual

Echo Auxiliary Control 1 of 3 Copyright © 2019 Savant Systems, LLC
009-1759-04 | 190603
Echo Auxiliary Control
Quick Reference Guide
The Echo Auxiliary Control is a companion to the Savant Echo wireless dimmers, and switches. The Auxiliary Control is wired in
such a way that allows for control of one load from multiple locations such as in a 3-way configuration. Multiple Auxiliary Controls
can be wired to one Savant Echo dimmer or switch.
The Auxiliary Control cannot be connected to a wireless network. All control signals from the Auxiliary Control are sent over a
traveler wire back to a Savant Echo style dimmer or switch. The Echo device then outputs the appropriate voltage to the load.
Product
Echo Auxiliary Control (WP3-xx0002-00)
Box Contents
(1) Auxiliary Control without faceplate
(2) Mounting Screws
(3) Wire Nuts
(1) Quick Reference Guide (this document)
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity
(non-condensing)
Location Indoor Use Only
Pollution Degree 2
Specifications
Dimensions
Height 4.13in (10.50cm) Shipping 7.0in (17.78cm)
Width 2.36in (6.00cm) Shipping 4.5in (11.43cm)
Depth 1.57in (3.99cm) Shipping 3.0in (7.62cm)
Weight Shipping 0.60lb (0.272kg)
Recommended Back Box Depth
All Echo switches require a standard U.S. electrical back box.
–Recommended - 3.5 in (8.89 cm) deep
–Minimum 2.25 in (5.72 cm) deep
–Type 1 enclosure for control
Power
Input 120V AC, 60Hz on Neutral wire (White)
Rated impulse
voltage 2500V
Regulatory
Safety and
Emissions
FCC Part 15 | UL
For more details, see the Regulatory and
Safety insert.
RoHS Compliant
Minimum Supported Release
da Vinci Blueprint 9.0
Installation
Operating
Control Type 1 action
Mounting
Independently mounted (vertical position only)
Hardware Overview
Front Panel
A
Pressing the main toggle button up or down will send data
over the traveler wire (yellow) to the master Echo dimmer
or switch.
A
Rear Panel
AWhite Neutral - Return path for voltage.
B
Green Ground - Wire to Gnd.
CYellow Traveler - Wire to one or more Auxiliary
Controls for multi-location control.
C
BA
Device wires are all a five inch #16 AWG stranded wire.

Echo Auxiliary Control 3 of 3 Copyright © 2019 Savant Systems, LLC
009-1759-04 | 190603
Echo Auxiliary Control 2 of 3 Copyright © 2019 Savant Systems, LLC
009-1759-04 | 190603
Electrician Removal/Installation
ELECTRIC SHOCK! The 120V AC, 60 Hz source power poses an electrical shock hazard that has the potential to cause serious
injury to installers and end users.
IMPORTANT NOTES!
–A licensed electrician is required to install any of the Echo wireless lighting devices. Isolate and turn o power at the main
breaker panel prior to installing any electrical devices.
–For supply, neutral, and ground connections use only #14 AWG or larger solid copper wires (80°C) with insulation stripped
to ⅝ in (16 mm).
1. At the main breaker panel, switch the breaker that supplies power to the circuit to O.
2. Unscrew the wall plate and remove. Verify power is removed using a 120V AC tester.
3. Unscrew the two 6-32 flat head screws and remove the existing toggle/rocker switch.
4. Disconnect wires from the existing device and remove the device. It is good practice to label each wire as it is removed. If not
already identified, mark wires to ensure proper rewiring. Especially if the circuit employs a 3-way configuration.
5. Connect the in-wall wires to the leads coming from the Echo Auxiliary Control using the supplied wire nuts or approved
alternative. Refer to either the Wiring Diagrams or Rear View Descriptions section.
6. Insert the Savant Auxiliary Control into the electrical switch box and secure with the 6-32 flat head screws provided. DO NOT
use a powered screw driver. A powered screw driver can over tighten the screws.
7. Re-establish power at the main breaker panel.
8. To test:
–If the Auxiliary Control is wired to a Echo wireless switch, toggle the main button to the On (up) position and observe the
load turns On. Toggle the main button to the O (down) position and observe the load turns O.
–If the Auxiliary Control is wired into a Echo wireless dimmer/keypad, press and hold the main button in the On (up) position
and observe the load increases in intensity. Press and hold the main button in the O (down) position and observe that the
load decreases in intensity.
NOTE: This test assumes a Savant Echo, Switch, or Keypad that the Auxiliary Control is connected to has previously been wired and
tested.
NOTE: Install the wall adapter to cover the metal yoke prior to
applying power. If replacing a Echo style device, remove
power before removing the wall plate adapter
Multi-Gang Installations
When combining multiple keypads into a multi-ganged box, the outside tabs from one or both sides of each device so they all fit
into the electrical switch box. Below are examples of 2, 3 and 4-gang scenarios.
–Tabs are removed from both sides of the inside gang devices.
–Tabs are NOT removed from outside edges of the devices at the end of each gang.
Wiring Diagrams
The diagrams below display how to wire the Echo Auxiliary Control as a companion to the Echo Dimmer/Switch. Both the basic
wiring as well as the No Neutral diagrams are shown. Any unused wires must have the bare wire portion (stripped end) cut o and
the wire must be capped with a wire nut.
From
Power
Example of two Auxiliary Controllers wired to Echo Dimmer/Switch
From
Power
Black
Tape
Black
Tape
Example of one Auxiliary Control wired to Echo Dimmer (No Neutral)
WARNINGS:
–Using the Echo Dimmer or Keypad in a No Neutral configuration with loads other than incandescent is not supported.
–The Echo Switch is not supported in a No Neutral 3-way configuration.
Wall Plate
Adapter
Wall Plate
Electrical
Switch Box
Mounting
Screws Wall Plate and Adapter
sold separately