Apposite Linktropy 5510 User manual

The Linktropy 5510 WAN Emulator is managed through a browser-based GUI over an Ethernet connection to
a dedicated management interface. Prior to operation, this management interface must be configured with
appropriate network settings, either through the Linktropy GUI or through a command-line interface accessed
via the serial console. For convenience, the management interface comes preconfigured with an IP address of
10.0.0.10, and the GUI is accessible from a directly-connected host on the 10.0.0.0/255.0.0.0 subnet.
Management of the Linktropy WAN Emulator requires a PC running a supported web browser (Internet Explorer, Firefox, Chrome or
Safari). JavaScript must be enabled.
Initial configuration of the management interface requires either:

a PC running a supported web browser that can be configured and placed on the 10.0.0.0/255.0.0.0 network.

a PC with an RS-232 serial port running terminal emulation software such as HyperTerminal or PuTTY.
The following product documentation is located at http://www.apposite-tech.com/resources/docs.html.
 Linktropy WAN Emulator User’s Guide
 Linktropy 5510 Hardware Guide
 Linktropy 5510 Quick Start Guide
The Linktropy 5510 is designed for installation in a standard 19” rack. See the Linktropy 5510 Hardware Guide for rack-mount installation
instructions.
Plug in a standard power cord (a U.S. power cord is supplied with the unit) into the socket on the back of the Linktropy 5510 and set the
power switch to the ON (1) position. When powered on, the Power LED on the front panel glows green. The system will be available for use
within 90 seconds.
To configure the management interface using the Linktropy GUI:

Configure a PC running a supported web browser with the IP address 10.0.0.2 or other address on the 10.0.0.0/255.0.0.0 subnet.

Connect an Ethernet cable between the PC and the MGMT port on the front of the Linktropy 5510.

Open the browser on the PC and enter http://10.0.0.10 (the preconfigured management address) in the address bar.
The Linktropy End User License Agreement will be displayed in a separate window.

Review the License Agreement. The Linktropy GUI will be displayed once the License Agreement is accepted.

The Linktropy GUI will open to the Device Settings tab. If desired, modify the IP address, netmask, and default gateway for the
management interface. Click the Apply Changes button when done.

Once the management interface has been configured, use the Ethernet cable to connect the MGMT port to the management network.

PREPARATION

IP ADDRESS CONFIGURATION VIA THE LINKTROPY GUI

HARDWARE INSTALLATION
Linkt ropy 5510
Quick Start Guide

For access to firmware upgrades, documentation, and other support materials, register your unit on-line at:
http://www.apposite-tech.com/register.html.
Copyright © 2005-2016 Apposite Technologies, Inc. All rights reserved. Apposite and Linktropy are registered trademarks of Apposite Technologies, Inc.
The Apposite logo is a trademark of Apposite Technologies, Inc.
Apposite Technologies, Inc. | 11500 W. Olympic Blvd. Suite 510 | Los Angeles, CA 90064 | www.apposite-tech.com
REGISTRATION

OPERATION
P/N. DOC- QSG-L5510-1b
Install the Linktropy 5510 between two LAN segments
as shown in the diagram. By default, the Linktropy
5510 acts as a bridge between the Ethernet segments
connected to the LAN A and LAN B ports. Frames
received on one port are subjected to the emulated
WAN conditions before being forwarded to the
opposite port.
Emulation conditions for the WAN link are configured
in the Linktropy GUI and operate independently in each
direction. To set the emulation parameters, use a web browser to connect to the Linktropy GUI at the configured management
address. All emulation parameters are found on the Link Emulation tab. Emulation is disabled until the red “Emulation On/Off”
button at the top of the screen is pressed. See the User’s Guide for details on Linktropy emulation parameters or click the 
buttons on the GUI for information on specific parameters.

IP ADDRESS CONFIGURATION VIA THE SERIAL CONSOLE
Using the provided RJ-45 to DB-9 cable, connect the serial
port of a PC running terminal emulation software to the
CONSOLE port of the Linktropy 5510. Set the serial port
parameters to 9600 baud, 8 bits, no parity, 1 stop bit, and
disable flow control. For more details on connecting to the
serial console, see the Linktropy 5510 Hardware Guide.
Press [ENTER] to display a login prompt. At the prompt, log
in as “admin”. Initially, there is no password.
linktropy login: admin
Use the following commands to set the IP address, netmask,
and default gateway of the Linktropy 5510 management
interface:
mgmt set addr <ip-address> netmask <mask>
mgmt set gw <default-gateway>
IP addresses and subnet masks are entered in
dotted-decimal format. For example:
mgmt set addr 192.168.1.1 netmask 255.255.255.0
Once the management interface has been configured, use
an Ethernet cable to connect the MGMT port of the Linktropy
5510 to the management network. Open a browser and
enter the IP address of the MGMT interface in the address
bar. The End User License Agreement will be displayed.

Review the License Agreement. The Linktropy GUI will be
displayed once the License Agreement is accepted.
To configure the management interface using the Linktropy serial console:
i
LAN A LAN B
CONSOLE MGMT PORT 1 PORT 2
LINKTROPY 5510
CONSOLE MGMT LAN A LAN B
MGMT