April identiti User manual

6
PH2 TYPE
2.75
INSTALLATION INSTRUCTIONS www.aprilproducts.co.uk
Tools Required
Lifetime Product Guarantee
ATTENTION!
Are you fitting this April enclosure to an April
shower tray?
The Lifetime Product Guarantee is only valid
when an April enclosure is fitted with an April
shower tray and are used and maintained in
accordance with the manufacturer’s instructions
(guarantee excludes seals and magnets).
When April enclosures are used with any other
shower tray the guarantee period is limited to
10 years.
Please see our website for full Terms &
Conditions.
To activate your Product Guarantee please visit
www.aprilproducts.co.uk and complete the
online form.
Pivot Door
This product should be installed by a suitably qualified and proficient person. The fitting instructions should be
followed carefully to ensure a proper and safe installation. Failure to follow these instructions could result in future
injury.
These instructions and list of parts assume that installation is done against solid/tiled walls.
Please check this product for damage prior to starting the installation. No claims can be made after the product has
been fitted.
PLEASE NOTE :The minimum and maximum adjustment sizes noted on the product brochures are based on
perfectly plumb walls and trays.

COMPONENTS AND BOX CONTENTS
2
Box Contents
Note : keep the factory installed foam
blocks in place on the top and bottom
of the glass. These are to assist in the
installation process.
No. Qty
1Wall Profile 2
2Cover Strip 2
3Upright Profile 1
41
5Horizontal Profile 2
6Upright Seal 1
7Horizontal Seal 1
81
9Frame Seal 1
10
Upright Profile Cap 2
11 Wall Profile Cap-L 1
12 Wall Profile Cap-R 1
13 Horizontal Profile Cap-L 2
14 Horizontal Profile Cap-R 2
15 Washer 4
No. Qty
16 Pivot Core 2
17 Pivot Gasket 2
18 2
19 4
20 Pivot Back Cap 2
21 Pivot Clamping 2
22 Round Washer 4
23 Handle 1
24 Wall Plug 8
25 Screw ST3.5x10 12
26
Screw M5x12
4
27 Screw ST3.5x40 8
28 Screw ST4x30 8
29 Moving Glass Panel 1
Fixing For Pivot
Cover Cap

IMPORTANT - Missing Components
Please check this product for missing components prior to installation.
For spare parts visit www.aprilproducts.co.uk
IMPORTANT - Installation site
1. Ensure the top surface of the shower tray on which the enclosure will be installed is level in every direction.
2. The tiles or other wall finishing should be effectively sealed at tray edges.
3. Tiles should extend at least to the corner of the tray and a minimum of 1.9 meters from the top of the tray.
FIXING KIT COMPONENTS, SITE CONDITIONS
FIXING KIT
3
Wall Profile Top
× 2
Upright Profile Top
× 2
Pivot Clamping
x2
Glass Gasket
x4
Cover Cap
x2
Pivot Back Cap
x2
Fixing For Pivot
x2
Pivot Core
x2
Pivot Gasket
x2
Cover Cap Cover Cap
Horizontal Profile
Cap
× 2
Wall Plug
8 pcs
Round Head
Tapping Screw
4 × 30
8 pcs
Round Head
Tapping Screw
3.5 × 10
8 pcs
ID2 Handle
Handle × 1
Grip Handle A × 1
Screw Cap × 2
Washer × 4
Countersunk Screw × 2
M4×12
Grip Handle B × 1

Step 2.
2.1 Remove the wall profiles and drill the marked points using a 6mm masonry drill bit, once this is done insert 8 × wall
plugs .
2.2 Fix the wall profile to wall using the screws ST4 × 40 .
Step 1.3
Step 2.1
Step 1.1 & 1.2
Step 2.2
Step 1.
1.1 Position the wall profiles to wall as shown (roughly 10mm from the front of the tray).
1.2 Level the frame using a spirit level.
1.3 Once you are happy that the frame sits on the tray correctly mark the wall through the 4 pre-drilled screw holes in the
wall profiles.
NOTE: You may find it easier to mark and drill the wall if you apply masking tape to it first.
10mm 10mm

Step 3.
3.1 Push the other wall profile to the hinged side.
3.2 Then insert the frame into the fixed wall profile as shown.
Step 4.
Fix the other wall profile using screws ST4 × 40
Step 5.
Adjust the frame to ensure that it is central between the wall profiles and level against the shower tray at the base.
Step 3.1 & 3.2
Step 4
Step 5
2
1
Step 3.1
Step 3.2

Step 6.
6.1 Drill 3 equally spaced holes with a 2.75mm drill bit through the wall profiles and frame.
6.2 Fix the frame to the wall profiles using the screws ST3.5 × 10
Step 6.1
Step 7.
Fix the handle to door panel.
Step 8
Step 8.
Once you are happy that the installation is correct, push the cover strip profile onto the wall profile as shown above.
Step 6.2
Step 7

Step 9.
Fit the upright profile top caps and wall profiles top caps as shown.
24 HRS
DO NOT USE THE
ENCLOSURE FOR
24 HOURS AFTER
SEALING
Applying Silicone Sealant
Sealing Inside
Seal from the top of the wall profile to the bottom on the INSIDE
between the wall profile and the wall.
IMPORTANT: Do not apply sealant on inside of the tray.
Sealing Outside
Seal from the top of the wall profile to the bottom between the
wall profile and tiles on both sides. Also seal along the bottom
where the frame meets the tray. Seal the joints between the
bottom profile and any upright profiles.
Step 9

This product has been treated with Clean & Clear™ easy clean glass treatment, a protective barrier which creates
a ‘non-stick’ surface on your glass, helping to resist lime scale build up and water spots. For further information on
Clean & Clear™ please visit www.aprilproducts.co.uk
Clean & Clean™ glass can be cleaned with any suitable nonabrasive glass cleaner - with PH value of between 3-
11; the coating will not be damaged. Avoid surfactants and heavily perfumed products. Vinegar and water based
products are very effective. Do not use abrasive scrubbing cleaners or equipment for cleaning.
Limited 5 year Warranty for Clean & Clear™ treatment: To guarantee treated surfaces will remain more repellent
than untreated glass for 5 years from start of use, as long as basic manufacturer maintenance recommendations
are followed and no harsh or abrasive cleaners are used.
It is important to clean your April shower enclosure after every use. Please wipe down all glass and metal parts
with a clean soft cloth. Ensure that all residual water on the glass is removed after every use.
For reliable, watertight performance from your April enclosure your shower head should not be positioned so that
the shower sprays directly onto the enclosure door. Failure to comply with this may cause the shower to leak.
Outward opening doors may cause water to drip onto the floor, please ensure that the floor covering immediately
outside the enclosure will not be affected by water.
APRIL PRODUCTS
Riverside Business Park, Royd Ings Avenue, Keighley, West Yorkshire, BD21 4AF
For technical/aftersales queries,please visit our website:
www.aprilproducts.co.uk
or Sales Tel: [phone] Technical: 01535 613830 Fax: [phone]