APS TS400 Instruction Manual

APS Annunciator System
TS400
Installation & User Manual TS400-DM
serial

TS400-DM serial
Safety and installation
For your own safety, please read this manual carefully and follow the instructions. Improper
handling can damage the device.
Cleaning:
Do not use any liquid cleaner or corrosive agent but solely a dampened cloth.
Installation:
Installation should be performed by certified personnel only.
Keep the cable connecting the TS400-DM serial as short as possible.
Utilize V.24 Interface standards
Mounting:
The TS400-DM serial is NOT Waterproof. Please do not mount outside unless protected
and avoid condition of high humidity and condensation
If mounted on an uneven surface, additional action might be necessary to seal the casing
and prevent dust from entering.
The DM serial has thread holes in order to be mounted on surfaces (Screws M4 x 5mm).
The DM serial features a VESA-Norm (75x75mm) rear mounting plate for a Monitor Arm or
Wall Mount.
Connection:
The DM serial uses the same wire assignment as the Power over
Ethernet Technology. Therefore, only one cable is necessary to
connect the DM serial. Please make sure that the used cables
are fully equipped and not crossed. PIN 6 must not be used.
The TS400-DM serial can be integrated in the TS400 annunciator system in two ways:
Local directly connected to the CPU's serial interface (Com 2). An adapter for the power
supply has to be connected
External integrated in the network (Technet) using a LAN-modem, also in this case, an
adapter for the power supply has to be connected
Pin
1
2
3
4
5
6
7
8
Description
TX
RX
GND(5V)
24VDC+
24VDC+
5V+
24VDC -
24VDC -
Used for
Signal
Signal
Signal
Supply
Supply
Empty
Supply
Supply

TS400-DM serial
Control panel:
1. Display
2. Visual alarm indicator lamp
3. Horn acknowledgement (HQ)
4. Lamp acknowledgement (LQ)
5. Double acknowledgement
6. Input, Delete button
7. Input, Confirm button
8. Navigation buttons
Sequence of functions:
In basic mode, the display backlight is dimmed and shows the system status, date and time.
In this mode, any button pressed will illuminate the display and list the current alarms.
An alarm caused by a fault signal is represented by the system as followed:
The horn is reset und shut off by pressing the button horn acknowledgment (3).
The Navigation buttons, illuminated during an alarm, allow the selection of a listed alarm
, or additional information regarding the selected alarm .
Pressing the button lamp acknowledgement causes the visual alarm indicator lamp to
change from flashing red to steady red when a fault signal remains, or extinguishes when
the fault signal is resolved (DIN 19235).
In case the system is set up for double acknowledgement, press the button double
acknowledgement (5) to do so.
The in the display listed alarms expires automatically after the fault signal is acknowledged
and solved.
The button Input Delete (6) is used to exit whilst being in menu.
The Input Confirm button (7) is used to confirm an entry e.g. after setting the clock.
Status display:
Possibility 1:
The horn and the fault are acknow-
ledged when the fault is still active
Possibility 2:
The horn and the fault are acknow-
ledged after the fault was solved
Possibility 3:
The horn was acknow., the fault solved
then the fault was acknowledged
1Ahl: was initiated
1Ahl: Fault was initiated
1Ahl: Fault was initiated
1AHl: Horn was acknowledged
0Ahl: Fault was solved
1AHl: Horn was acknowledged
1AHL: Fault was acknowledged
0AHl: Horn was acknowledged
0AHl: Fault was solved
0AHL: Fault was solved
(expires automatically)
0AHL: Fault was acknowledged
(expires automatically)
0AHL: Fault was acknowledged
(expires automatically)
2

TS400-DM serial
Technical data:
Mass
250 x 175 x 24 mm (WxHxD)
Weight
1320g
Case
Aluminium anodized
Display
LCD graphics-enabled
Backlit
Text: 16 rows x 30 characters
Temperature range
0 to +55 °C
Degree of protection
IP40
Power
8 W
Operating voltage
Nominal 24VDC
Assembly
Closet front
Monitor pedestal
Wall mount VESA
Order overview:
832.700.420
TS400-DM serial text display
832.700.490
VESA wall mount
832.400.911
Transition module RJ45
Dimensions: Connection principle:
Doc-0010-E_05.19
APS systems AG
Neumatt 4
CH-4626 Niederbuchsiten Tel. [phone]
Switzerland E-Mail: [e-mail] www.aps-systems.ch