Aqua ZODIAC MX 6 User manual

1
WARNINGS
GENERAL WARNINGS
• Failure to respect the warnings may cause serious damage to the pool equipment or cause serious injury, even death.
• The appliance is intended for use in swimming pools only and must not be used in applica on other than that for which
it is designed.
• It is important that the equipment is operated by competent and qualifi ed (both physically and mentally) people who
have previously received the instruc ons for use. All persons not mee ng these criteria must not approach the appliance
in order to avoid exposure to dangerous elements.
• Keep the appliance out of the reach of children.
• The appliance must be installed in accordance with the manufacturer’s instruc ons and respec ng current local
standards. The installer is responsible for installa on of the equipment and for compliance with na onal installa on
regula ons. Under no circumstances can the manufacturer be held liable in the event of failure to comply with applicable
local standards.
• For other than the simple user-maintenance described in this manual, the product must be serviced by a qualifi ed pro-
fessional.
• Incorrect installa on and/or use may cause serious damage to property or serious injuries (possibly causing death).
• All equipment, even postage and packing paid, travels at the risks and perils of the recipient. The consignee shall make
reserva ons in wri ng on the carrier's bill of lading if damage is detected, caused during transport (confi rma on to
be sent to the carrier within 48 hours by registered mail with acknowledgement of receipt). In the event of a device
containing coolant that has been turned on its side, men on your reserva ons in wri ng to the carrier.
• If the appliance suff ers a malfunc on, do not try to repair the appliance yourself, contact a qualifi ed technician.
• Refer to the warranty condi ons for details of the permi ed water balance values for opera ng the appliance.
• Defea ng, elimina ng or shun ng any of the safety that may be a part of the device automa cally voids the warranty, as
does the use of unauthorized, third party replacement parts.
• Do not spray insec cide or any other chemical (infl ammable or non-infl ammable) in the direc on of the appliance, as
this may damage the body and cause a fi re.
• Zodiac® Heat pump, fi ltra on pump and fi lter appliances are compa ble with most commonly used pool water treatment
systems.
• For heat pump appliances or dehumidifi ers, do not touch the fan or insert a rod or your fi ngers through the gra ng when
the appliance is in opera on. The fan rotates at high speed and may cause injuries or even death.
SPECIFIC FEATURES APPLICABLE TO "Pool cleaners"
• The cleaner must operate in pool water with a temperature of between 15°C and 35°C.
• To avoid possible injury and damage to the cleaner, do not operate the cleaner out of the water.
• In order to prevent possible injury, bathing is prohibited when your cleaner is in the pool.
• Do not use the cleaner during shock chlorina on.
• Do not leave the cleaner una ended for an extended period.
WARNING ON THE USE OF A CLEANER IN A POOL WITH A VINYL SURFACE:
• Before installing your new cleaner, carefully inspect the lining of your pool. If the liner has eroded in some areas, or if you
no ce gravel, folds, roots or corrosion caused by metal on the inner surface of the liner, or if you no ce that the support
(bo om and walls) is damaged, do not install the cleaner before performing the necessary repairs or before replacing the
liner using a qualifi ed professional. The manufacturer may not be held liable in any way for damage caused to the liner.
• The surface of certain vinyl pa erned surfaces can wear rapidly and the pa erns disappear on contact from objects
such as cleaning brushes, toys, infl atable buoys, chlorine distributors and automa c pool cleaners. The decora on on
some vinyl surfaces can be scratched or worn by basic fric on such as through the use of a pool brush. The colours of
certain pa erns can also be erased during use or when in contact with objects in the pool. The erased pa erns, wear or
scratching of vinyl surfaces are not the liability of the manufacturer and are not covered by the limited warranty.
Recycling
This symbol means that your appliance must not be thrown into a normal bin. It will be selec vely collected for the purpose of
reuse, recycling or transforma on. If it contains any substances that may be harmful to the environment, these will be eliminated
or neutralised.
Contact your dealer for recycling informa on.

2
CONTENTS
❶ Specifi ca ons 3
1.1 I Descrip on 3
1.2 I Technical specifi ca ons and marking 4
❷ Installa on 5
2.1 I Setup 5
2.2 I Twist Lock Hose sec on assembly 5
2.3 I Hydraulic connec on 6
❸ Use 8
3.1 I Opera ng principle 8
3.2 I Pool prepara on 8
3.3 I Opera ng 8
3.4 I Adjus ng the water fl ow 9
3.5 I Choice of suc on mode: small or large debris (according to model) 10
❹ Maintenance 11
4.1 I Cleaning the fi ltra on pump basket 11
4.2 I Cleaning the "CyclonicTM" Leaf Catcher 11
4.3 I Removing debris from the motor 12
4.4 I Replacing the tracks 12
4.5 I Storage and wintering 13
❺ Troubleshoo ng 14
5.1 I Device behaviour 14
• Before you do anything with the device, it is vital that you read this installa on and user
manual, as well as the "warnings and warranty" booklet delivered with the device. Failure to
do so may result in material damage or serious or fatal injury and will invalidate the warranty.
• Save these instruc ons for future reference for service and maintenance.
• It is prohibited to distribute or modify this document in any way without authorisa on from
Zodiac®.
• Zodiac® is constantly developing its products to improve their quality; therefore, the
informa on contained in this document may be modifi ed without no ce.
Tip: to make it easier to contact your reseller
Write down your reseller's contact details to help you fi nd them more easily and fi ll in the "product"
informa on on the back of the manual; your reseller will ask you for this informa on.
EN

3
❶ Specifi ca ons
1.1 I Descrip on
MXTM 6 - MXTM 630 MXTM 8MXTM 8 PRO MXTM 9
A
Cleaner
B
C
D1 metre Twist Lock hose fl oat sec on (x1)
E1 metre Twist Lock hose sec on ( x9) ( x11) ( x11) ( x11)
FFlow regulator valve
G In-ground valve cuff
H45° fl exible elbow
IFlowkeeper valve
J45° Twist Lock elbow extended
K“CyclonicTM” Leaf Catcher”
L Rota ng 45° extended elbow
MSet of 6 1-metre Twist Lock hose sec ons
NWintering bag for hoses
: Supplied
: Available as an op on

4
1.2 I Technical specifi ca ons and marking
1.2.1 Technical specifi ca ons
MXTM 6 - MXTM 630 MXTM 8 MXTM 8 PRO MXTM 9
Cleaner size (L x W x h) 31 x 19 x 22 cm 41 x 19 x 22 cm
Package size (L x W x h) 102 x 23 x 37 cm
Cleaner weight 2.5 kg 3.2 kg 3.4kg
Packaged weight 8.2 kg 9.5 kg 10.5 kg 9.5 kg
Theore cal cleaning width 25 cm 36 cm
Filtra on capacity Pool fi ltering circuit
Minimum powered required for
the fi ltering pump. 3/4 HP
Movement speed 8 m/ min
1.2.2 Marking
: Flow regulator valve
: Twist Lock Hose sec on
: Cover opening bu on
: Tracks
: Wheels
: Turbines
: Brushes
EN

5
❷ Installa on
2.1 I Setup
Hose length necessary : Cleaner
: Twist Lock Hose
sec ons
: Pool valves
: Suc on line
: Skimmer
: Filtering pump
: Filter
Suc on line connec on example
2.2 I Twist Lock Hose sec on assembly
2.2.1 Determine the number of sec ons you need
• Measure the length between the suc on line or the skimmer and the furthest away point of the pool.
• Add an extra 1 metre to the length measured.
• If total length is over 10 metres (MXTM6-MXTM630) or 12 metres (MXTM8-MXTM8 PRO), contact your reseller to purchase
any addi onal Twist Lock hose sec ons required for your pool.
: Connec on to the suc on line or
the skimmer
: Hose length necessary
: 1 metre sec on of Twist Lock
hose with fl oat
: Connec on to the cleaner
Tip: insert the "right" quan ty of Twist lock hose sec ons
Inser ng more Twist Lock hose sec ons than the length necessary to cover the whole pool is not
recommended. Hoses that are too long may limit the cleaner's performance.
2.2.2 Twist Lock Hose sec on assembly
• To assemble two Twist Lock hose sec ons, insert them then turn them un l the connectors are at the maximum stop
point, in one of the 3 notches that provide the seal (see image ).
• The sec on of Twist Lock hose with the hose fl oat a ached will be connected to the cleaner (see image ). The Twist
Lock hose fl oat must be located 20-23 cm away from the cleaner. (see image ).
20-23 cm Float

6
2.3 I Hydraulic connec on
• Turn off the fi ltra on pump.
• Clean the skimmer basket, the fi ltra on pump fi lter basket and the fi lter if necessary.
2.3.1 Connec on to the suc on line
or
: Twist Lock Hose sec on
: Suc on line
: 45° Twist Lock elbow extended (according
to model)
: Rota ng 45° extended elbow (according to
model)
2.3.2 Connec on to the skimmer
• If the pool has more than one skimmer, connect the pipe to the one which is the closest to the fi ltra on pump.
: In-ground valve cuff
: Flowkeeper valve
: 45° fl exible elbow
: Twist Lock Hose sec on
: Skimmer
Tip: Protect the fi ltra on system by connec ng the fl owkeeper valve
This valve is used to adjust the fl ow to op mise the cleaner's performance; it is also very useful for retaining
any debris that may be sucked in and damage the fi ltra on equipment.
EN

7
2.3.3 "Cyclonic™ Leaf Catcher" connec on (according to model)
• Connect the CyclonicTM Leaf Catcher to the Twist Lock hose assembly which is closest to the suc on line or the
skimmer (see image or ).
• Tilt the CyclonicTM Leaf Catcher by following the indica ons: "PUMP" = fi ltra on pump side / "CLEANER" = cleaner
side (see image ).
• For the bet opera on, posi on the CyclonicTM Leaf Catcher ver cally to the water surface (see image ).
Connec on to the suc on line Connec on to the skimmer Connec on direc on
Ver cal posi on
Tip: Protect the fi ltra on system by connec ng the CyclonicTM Leaf Catcher
The CyclonicTM Leaf Catcher is used to retain the debris before it is sucked into the fi ltra on system as this
may cause long-term damage to the equipment. It also enables the debris to be removed more easily than
in the pump fi lter basket, and has the advantage that it is transparent so you can see when it needs to be
cleaned.

8
❸ Use
3.1 I Opera ng principle
The hydraulic cleaners connect to the fi ltra on system (either to a suc on line or a skimmer); they use the fi ltra on
pump’s energy to move around the pool. The wall climbing capacity varies according to the shape of the pool and the
available water fl ow.
The debris is sucked in by the cleaner and captured in the fi ltra on pump's fi lter basket or in the CyclonicTM Leaf Catcher
(accessory included or available as an op on depending on the model).
3.2 I Pool prepara on
• The device must operate in pool water with the following quality:
Water temperature Between 15°C and 35°C
pH Between 6.8 and 7.6
Chlorine < 3 mg/ l
• When the pool is dirty, especially when fi rst installing your cleaner, remove the largest debris using a telescopic pole
and net prior to installing the cleaner.
• Remove any thermometers, toys and other objects that might damage the device.
• A er adding chemical products to the water, wait at least 4 hours before pu ng the cleaner into the water.
• Make sure that the fi ltra on and the skimmer baskets are clean.
• Aim the pool return lines downward if adjustable.
• Close the pool’s main drain line.
• Turn off the fi ltra on pump off .
3.3 I Opera ng
• Do not expose your hair, lose clothing, jewellery, etc. to the open end of the hose.
• To avoid serious injury, make sure the fi ltra on pump is turned off .
3.3.1 Connec ng the fl ow regulator valve and immersing the cleaner
• Insert the Twist Lock hose fl oat onto the fl ow regulator valve (see image ).
• Immerse the cleaner so that it fi lls up with water.
• When there are no more air bubbles escaping from the cleaner, connect the hose by inser ng the fl ow regulator valve
onto the cleaner (see image ).
• Wait un l the cleaner descends to the bo om of the pool.
3.3.2 Filling the Twist Lock hose assembly
• Disconnect the Twist Lock hose assembly to the suc on line or skimmer temporarily.
• Turn on the fi ltra on pump.
• Fill the Twist Lock Hose assembly with water by placing the open end in front of a pool return line un l it is fi lled.
• Turn off the fi ltra on pump and connect the Twist Lock Hose assembly to the dedicated suc on line or skimmer.
• Turn on the fi ltra on pump on to ac vate the pool cleaner.
EN

9
3.4 I Adjus ng the water fl ow
• The fi ltra on pump must be opera ng.
• Check the water fl ow regularly to ensure the best possible cleaning performance and to make it easier for the cleaner
to climb the sides.
• The cleaner is equipped with a fl ow regulator valve which automa cally adjusts the water fl ow through the cleaner. It
indicates whether the water fl ow is ok or excessive: YELLOW = fl ow ok / RED = fl ow excessive
: Flow regulator valve
: Control
3.4.1 Checking the wheel rota on speed
• The fi ltra on pump must be opera ng.
• Switch on the fi ltra on pump (have a stopwatch ready).
• Raise the cleaner to below the surface of the water, keeping it submerged.
• Note the yellow indicator on the rear right wheel (voir image
Raise the cleaner to below the surface of the water, keeping it submerged.
).
• For MX8-MX8 PRO: Wait un l the wheels change direc on and log the  me un l the wheels have performed 10 turns
(see image
For MX8-MX8 PRO: Wait un l the wheels change direc on and log the  me un l the wheels have performed 10 turns
).
• Adjust the water fl ow according to the  me logged (see image ).
10 turns
Seconds
26-50
20-25
10-19
Increase the fl ow
Flow ok
Reduce the fl ow
3.4.2 Adjus ng the water fl ow
• Adjust the water fl ow using the fl owkeeper valve provided with the device (see image ), or from the pool valves.
(+) Increase the fl ow
(-) Reduce the fl ow

10
3.5 I Choice of suc on mode: small or large debris (according to model)
Before star ng this opera on and to avoid serious injury:
• Turn off the fi ltra on pump.
• Disconnect the cleaner from the Twist Lock hose assembly.
• The cleaner has a suc on adaptor; it is located under the cleaner.
• The adaptor enables the suc on to be adjusted according to the type of debris to be dealt with: "small debris" mode
(small or heavy debris such as sand, silt and stones), "large debris" mode (leaves).
• To switch to "large debris" mode: remove the adaptor by inser ng a fi nger into it and raising the rear edge.
• To return to "small debris" mode: press the front and rear edges of the adaptor to clip it into its housing.
: Suc on adaptor
: "Small debris" mode (default)
: "Large debris" mode
Tip: It is best to use "small debris" mode during the bathing season
When the pool is cleaned regularly, we recommend that you leave the suc on adaptor in place to be in
"small debris" mode.
EN

11
❹ Maintenance
• The device must be cleaned regularly using clean or slightly soapy water. Do not use any solvents.
• Rinse the device generously using clean water.
• Never store the cleaner in direct sunlight. Store the hoses laying fl at and not coiled to prevent unwanted hose memory.
4.1 I Cleaning the fi ltra on pump basket
• Always remove the cleaner from the pool before cleaning or bleeding the fi ltra on system.
• Before cleaning (and before you put the cleaner back into the water), start the fi ltra on pump
for at least 5 minutes before you bleed the circuit.
• For maximum cleaner performance it is recommended the fi ltra on pump basket be kept clean by removing debris
as needed.
• Use of the CyclonicTM Leaf Catcher (accessory included or op onal depending on the model) is recommended to
collect large debris before it reaches the skimmer and the pump basket.
4.2 I Cleaning the "CyclonicTM" Leaf Catcher
• Turn off the fi ltra on pump.
• Keep the CyclonicTM Leaf Catcher under the water and take hold of it by the handle. Using the handle, turn the
transparent canister un l it detaches (see image ).
• Remove the transparent canister from the water and leave the lid and the hoses under the water (see image ).
• Remove the fi lter using the top handle (see image ).
• Remove the debris and rinse the transparent canister in clean water (see image ).
• Put the fi lter back in place and immerse the CyclonicTM Leaf Catcher again (see image ).
• Posi on the transparent canister correctly on the lid notches then turn it sharply to push the 2 parts in (see image ).

12
4.3 I Removing debris from the motor
Before star ng this opera on and to avoid serious injury:
• Turn off the fi ltra on pump.
• Disconnect the cleaner from the Twist Lock hose assembly.
• Press the bu on on the top and li the lid (see image ).
• Remove the debris inside (see image ) and also under the cleaner (see image ).
• If necessary, gently push the motor blades forward and backward to reveal any trapped debris and remove it. When
you move the blades, make sure that the cleaner's tracks turn freely and that they are correctly synchronised with the
movement of the blades under the cleaner.
• Also remove any debris which may be caught in the suc on inlet.
• Close the lid and make sure it locks.
4.4 I Replacing the tracks
• Lay the cleaner on one side.
• Star ng with one of the wheels, pull the inside of the track to separate it from the wheel (see image ). Then remove
the track from the cleaner.
• To install the new track, posi on the inside of the track on the small wheel's grooves and on one of the large wheels.
• Stretch the track around the second wheel, (see image ). Press down on the track to posi on it correctly on the
wheel grooves. Make sure that the track passes under the guide.
EN

13
4.5 I Storage and wintering
• For wintering, drain off all the water from the cleaner (damage caused by frost is not covered by the warranty).
• Clean the whole device and the hoses in clean water then leave to dry.
• Store the device in a dry place which is protected from freezing condi ons. Store the cleaner on its side or back to
avoid damage to turbine (voir image ).
• Remove all the connectors and adaptors from the suc on line or the skimmer.
Tip: Preserve the condi on of the hoses during storage
When the cleaner is stored away, even for short periods, avoid rolling the hoses: they may take on a shape
which may harm the cleaner's performances.

14
❺ Troubleshoo ng
• Before you contact your reseller, please carry out these few simple checks using the following
tables if a problem occurs.
• If the problem con nues contact your reseller.
5.1 I Device behaviour
The cleaner is
immobile or very
slow.
• Close the pools main drain line.
• Clean and empty the skimmer and fi ltra on pump baskets.
• Inspect the motor area and remove any visible debris. (see “4.3 I Removing debris
from the motor”)
• Remove the suc on adaptor under the cleaner (see “3.5 I Choice of suc on mode:
small or large debris (according to model)”).
• Check the fl ow (see “3.4 I Adjus ng the water fl ow”).
• Turn on the pools fi ltra on pump to verify there is no air in the system. If the fi ltra on
pump basket is fi lled with air bubbles and, or the water level is low this indicates
there is air present in the circula on system. If air is in the system it will be seen as
water fl ows out the pool return lines. Air can be drawn into the circula on system
through components on the suc on side of the fi ltra on pump. This includes holes
or cracks in the cleaners twist lock hose sec ons.
• Verify the pool surface is not covered with algae as this slippery surface will not
allow the cleaner to gain trac on and climb. If it is, carry out shock chlorina on and
slightly reduce the pH.
The cleaner does
not cover the
en re pool.
• Check the fl ow (see “3.4 I Adjus ng the water fl ow”).
• Aim the return line fi  ngs in the pool downward if adjustable.
• Check the Twist Lock hose sec ons for coils. If a memory has formed turn off the
cleaner and remove the aff ected twist lock hose sec ons. Place the coiled twist lock
hose sec ons on a fl at surface in the sun un l the sec ons lay fl at. Re-install the
twist lock hose sec ons on the cleaner.
• Check the Twist Lock hose assembly is long enough (see “2.2 I Twist Lock Hose sec on
assembly”). If it is not, add hose sec ons.
• Check the posi on of the hose fl oat on the leader hose sec on (see “2.2 I Twist Lock
Hose sec on assembly”).
• Monitor the cleaner for more than fi ve minutes and check that each track changes
direc on regularly.
The cleaner is
stopped on the
steps.
• Check the top cover swivel turns freely.
• Test the fl ow by checking the wheel rota on speed (see “3.4.1 Checking the wheel
rota on speed”).
• Check hose fl oat is correctly posi oned (see “2.2 I Twist Lock Hose sec on assembly”).
If it is, shorten it by removing sec ons.
The cleaner does
not climb the pool
walls.
• Check the fl ow (see “3.4.1 Checking the wheel rota on speed”) and increase it if
necessary (see “3.4.2 Adjus ng the water fl ow”).
• Check that the hose fl oat is correctly posi oned (see “2.2 I Twist Lock Hose sec on
assembly”).
• Check that the pool walls are free of algae and not slippery.
The cleaner climbs
above the water
line.
• Reduce the fl ow (see “3.4.2 Adjus ng the water fl ow”).
• Check that the hose fl oat is posi oned properly on the leader hose (see “2.2 I Twist
Lock Hose sec on assembly”).
The cleaner lays
on its side. • Check that the hose fl oat is posi oned correctly on the leader hose.
EN