Aquasana OptimH2O AQ-RO3-R User manual

AQ-RO3-R
Under Sink Water Filter
Owner’s Manual
OptimH2O®Reverse Osmosis + Claryum®
Carbon & Claryum®Filter
REPLACEMENT
For use with AQ-RO-3

Shut o the cold water valve under the sink. Release the pressure from
the system by turning on the dedicated faucet. Once there is no longer any
water owing, you can proceed with replacing the lters.
Unbox lter replacements and remove plastic. Each lter is color coded to
match the circle indicator on each lter housing.
Remove each lter housing from the system manifold by turning the lter
housing to the left. Pull down to detach. Ensure the lter housings are not on
an angle while removing. This may result in damage to the o-ring.
Holding the lter
housing over the sink,
open it by turning the
bottom counter-clockwise.
Pour excess water down
sink drain. Pull down on
dirty lter to disconnect it
from the lter housing.
Continue this step for the
second lter housing.
While the housing is open,
inspect each o-ring for damage. If damaged, replace immediately. If
misaligned, gently move the o-ring into place.
1
1
23
3
3
2
1
1
2
2
1
1
1
23
3
3
2
1
1
2
2
1
1
1
23
3
3
2
1
1
2
2
1
1
1
23
3
3
2
1
1
2
2
1
1
1
23
3
3
2
1
1
2
2
1
1
1
23
3
3
2
1
1
2
2
1
1
1
23
3
3
2
1
1
2
2
1
1
1
23
3
3
2
1
1
2
2
1
1
2
3
4
NOTE: Must replace housing every 5 years or risk property damage from leaks.
Call 866-662-6885 to order.
NOTE: If lter housing is too tight to disconnect by hand, please use the plastic
wrench included with original system.
NOTE: Do not use with water that is microbiologically unsafe or of unknown
water quality without adequate disinfection before or after the system.
INSTALLATION STEPS

Once both lter housings have been replaced and reattached,
slowly turn water valve on. Turn o faucet and allow the water tank
to completely ll.
Once the tank has completely lled, inspect for leaks. Then,
ush system until there is no longer any water pressure coming
out of the faucet.
Turn o the faucet and allow 2 hours for the pressure to build
back up in the system. After pressure has built back up, your
system is ready to use.
Press new replacement lter to the top of
the lter housing using the appropriate color
coded lters. Then, reconnect the bottom
of the lter housing to the top half. Ensure
connection points are correctly aligned, then
turn clockwise to tighten. Continue this step
for the second lter housing.
Reattach lter housing to the
bottom of the system manifold.
Ensure connection points are
correctly aligned, then push the lter
housing up while turning clockwise.
Continue this step for the second
and third lter housing. Ensure all
lter housings are locked in place, are not on an angle,
and are aligned as pictured. Improper placement may
result in damage to the o-ring or leakage.
5
6
NOTE: Do not use tools to
tighten. Hand tighten only.
7
8
9
NOTE: Do not drink ushed water.
NOTE: This may take about 2 hours.
1
1
23
3
3
2
1
1
2
2
1
1
1
23
3
3
2
1
1
2
2
1
1
1
23
3
3
2
1
1
2
2
1
1
1
23
3
3
2
1
1
2
2
1
1
1
23
3
3
2
1
1
2
2
1
1
1
23
3
3
2
1
1
2
2
1
1
1
23
3
3
2
1
1
2
2
1
1
1
23
3
3
2
1
1
2
2
1

Protect your investment and save money
with our Water for Life program.
Free
Shipping
Discounted
Replacements
No
Contract
[email protected]
CONTACT US TO LEARN MORE 866-662-6885
Aquasana, Inc.
6310 Midway Road
Haltom City, Texas 76117
866.662.6885 USA
877.332.7873 Canada
www.aquasana.com
System tested and certied by WQA to
NSF/ANSI Standard 42 and 53 for the
reduction of the claims specied on the
Performance Data Sheet and at
www.WQA.org.
For the full list of
contaminants ltered,
scan to view the
Performance Data Sheet
on Aquasana.com.
The recommended replacement frequency for the AQ-RO3-R is every 6 months.
Use only certied, genuine Aquasana replacement lters for continued contaminant removal
and system performance.
Extended
Warranty