AquaStar Statztruck User manual

877.768.2717 fax: 877.276.POOL (7665)
Outside the U.S.: +1.805.620.5060 fax: [phone]
www.aquastarpoolproducts.com [email protected]
InstallatIon manual
AUTOMATIC SUCTION POOL CLEANER

remember these important facts!
Before installing the StarzTruck automatic pool cleaner:
• Manually clean/vacuum the pool and clean all skimmer, pump and debris baskets.
• Clean or backwash the filter.
• Check that the water is at its proper level.
• Check water chemistry – make sure the pool is free from excess algae to ensure proper operation of
StarzTruck automatic pool cleaner.
Never use the StarzTruck automatic pool cleaner to remove plaster/pebble debris in new or remodeled pools.
Always remove the StarzTruck automatic pool cleaner before backwashing or chemically shocking the pool.
•Programmed movement for better cleaning
•Efficient, quiet operation
•Highly engineered for durability
•Simple installation, no additional tools required
•Vinyl/fiberglass or concrete
•Easy grip roll bar handle
•Private label grill insert available
•Patent-pending design
THE STARZTRUCK AUTOMATIC SUCTION SIDE POOL CLEANER FEATURES:
KIT INCLUDES SEVEN CONNECTOR HOSES (30 FEET),
FLOW GAUGE, SKIMMER CONE AND OWNERS' MANUAL.
Thank you for purchasing the Statztruck automatic pool cleaner. Aquastar
proudly manufactures and assembles all of their products in the U.S. The
Starztruck automatic pool cleaner works from the suction side of your pool
filter - subject to the GPM (gallons per minute) of the suction line. For
technical assistance, call Aquastar Pool Products at 877.768.2717.

There are seven connector hoses. The hose cuff on any of the hose sections connects to the top of
the StarzTruck automatic pool cleaner (see Fig. 1).
Connect the StarzTruck automatic pool cleaner hose sections together by pushing and twisting the tapered
male connector end of each hose firmly into the open female end of the adjacent hose section (see Fig. 2).
Depending on the size and shape of your pool, all hose sections might not be used. The hose should reach
from the skimmer or safety vacuum lock wall fitting (AquaStar p/n VLK15Txx) to the furthest point in the
pool plus one extra hose section. If the hose is not long enough, it will be necessary to purchase additional hose
sections from your pool dealer. After the correct hose length has been assembled, fill the hose completely with
water by lowering the attached StarzTruck automatic pool cleaner and then vertically pushing the hose down,
allowing all the air to escape. When the hose is full, remove the StarzTruck automatic pool cleaner from the
hose and insert the flow gauge into the leader hose. Make sure the flow gauge is under water (see Fig. 3).
If optional leaf canister (AquaStar p/n HWN152) is purchased, install between first and second hose sections
(see Fig. 4).
STEP 1: CONNECTING AND SUBMERGING THE HOSES AND CLEANER
Fig. 2
Fig. 4
To StarzTruck Skimmer
First hose section
Second hose section
(showing leaf canister)
Fig. 1
Pool deck / coping
First hose section
To skimmer or vac-lock
Fig. 3

Connect a skimmer cone adapter and then insert the skimmer cone into:
A. The suction port of the skimmer (see Fig. 5) or
B. The wall port safety vacuum lock without a three-way or ball valve (see Fig. 6) or
C. Without the skimmer cone and regulator valve – insert the male end of the hose directly into the safety vacuum
lock wall fitting port – with a three-way or ball valve (see Fig. 7)
STEP 2: CONNECTING TO SUCTION
Fig. 5
HWN161 regulator valve
HWN152cone adapter
To pump
To StarzTruck
Hose
To main drain (if applicable)
Skimmer
Fig. 6
VLK15Txxx safety
vacuum lock wall fitting
Fig. 7
VLK15Txxx safety
vacuum lock wall fitting

Check the water flow reading on the Flow Gauge (refer to step 1, Fig. 3). The black disk should be in the box
between the “MIN” and “MAX” markings. If the setting is higher than required with the black disk outside
of the box on the “MAX” side and you have connected your hose to the skimmer, it will be necessary to
reduce the vacuum/water flow by using a valve or valves in the filter system, or the AquaStar hwn161
Regulator Valve or an optional AquaStar Automatic Skimmer Vacuum Plate designed to adjust vacuum/
water flow. To install the hwn161 Regulator Valve, turn the filter system off. Remove the hose from the
hwn152 Skimmer Cone, and after closing the Regulator Valve (rotate the blue collar clockwise/toward +
until closed/tight), insert the Regulator Valve into the Skimmer Cone, and insert the hose end into the
Regulator Valve (see Fig. 5 on previous page).
Turn the filter system on and allow it to run long enough to eliminate any air in the system. Turn the blue
collar counter clockwise until the proper reading appears on the gauge.
If you have connected your hose to the AquaStar Vacuum Lock, it will be necessary to adjust the vacuum/
water flow using the three-way valve at the filter system. The handle on the valve should be turned so that
the Flow Gauge which is installed in the StarzTruck hose reads properly (refer to Fig. 3 on page 2). After the
three-way valve has been properly adjusted, the vacuum gauge at the three-way valve should be marked
so that the water flow can be adjusted by referring to the gauge at the valve rather than reinstalling the
Flow Gauge in the hose each time an adjustment is necessary. Once the Flow Gauge has a proper reading,
remove it from the leader hose and reattach the StarzTruck automatic pool cleaner. Submerge the StarzTruck
back into the pool until it reaches the bottom for operation.
STEP 3: ADJUSTING YOUR STARZTRUCK AUTOMATIC POOL CLEANER

Some skimmers have a vari-flow or diverter valve in the bottom of the skimmer. This valve can be turned
to regulate skimming and main drain suction. Turn the valve to full skim and then adjust the Flow Gauge
vacuum gauge by turning the valve toward main drain suction. Usually this valve is the same size as the
hose end, and it will therefore be necessary to purchase an hwn158 Hose Connector (see Fig. 8). After the
proper gauge reading has been established, the diverter valve will have to be locked in place with a wedge
of some kind so that it won’t change position with operation of the StarzTruck.
Periodically check the water flow/vacuum to be sure that the StarzTruck is operating as efficiently as
possible. Remember, too much vacuum is just as bad as too little.
Periodically check to make sure that the StarzTruck hose is securely attached to its suction source
(i.e. Skimmer, Skimmer Vacuum Plate, Safety Vacuum Lock, etc.).
Disconnect the StarzTruck hose from the skimmer/regulator valve, or, if using a dedicated line, turn cleaner
valve off before backwashing, so that you’re not restricting water flow.
Never coil the StarzTruck hose. Damage caused by coiling the hose is not covered under the warranty.
When the StarzTruck is out of the pool, always disconnect the leader hose from the StarzTruck head.
Always carry the StarzTruck by the molded-in handle. Do not carry it by the hose.
When swimming in the pool, remove the StarzTruck from the water.
If you are going to super-chlorinate, shock or add gas chlorine to your pool, make sure the cleaner and hose
are removed before doing so.
STEP 3: ADJUSTING YOUR STARZTRUCK AUTOMATIC POOL CLEANER continued
Fig. 8
To pump
To main drain
Optional hose adapter
To StarzTruck
Hose
Skimmer diverter valve

The StarzTruck automatic pool cleaner will climb vertical walls in concrete and fiberglass pools (not vinyl)
if there is at least a 12-inch radius where the floor meets the walls. Because of the internal programmed gear
box, the cleaner will not climb the wall every time. Likewise, it will not always go all the way up the wall.
If the StarzTruck automatic pool cleaner is not sticking to the wall, set the rear flap to position III (see Fig. 9)
and/or adjust your regulator valve(s). If the cleaner climbs above the waterline and sucks air, set the rear flap
to position I (see Fig. 10) and/or adjust your regulator valve(s).
STEP 3: ADJUSTING YOUR STARZTRUCK AUTOMATIC POOL CLEANER continued
Fig. 10
Rear flap tension adjuster

PROBLEM: SLOW/NO FORWARD MOVEMENT
CAUSES SOLUTIONS
Lack of/improper water flow through cleaner Check and adjust water flow per step 3, Figs. 7, 8, 9, 10
Partial blockage of StarzTruck throat Clear blockage
Worn shoes Replace shoes
Worn wings Replace wings
PROBLEM: CLEANER FAILS TO CLIMB VERTICAL WALLS GUNITE/CONCRETE POOL
CAUSES SOLUTIONS
Improper shoes for application Call AquaStar
Lack of/improper water flow through cleaner Adjust water flow per step 3, Fig. 10
Partial blockage of StarzTruck throat Clear blockage
Worn shoes Replace shoes
Worn wings Replace wings
Hose too short Install additional hose sections per installation
Instructions
Improper tension on rear flap Turn rear flap adjuster to III
STARZTRUCK AUTOMATIC POOL CLEANER TROUBLESHOOTING GUIDE

PROBLEM: CLEANER CLIMBS TO SURFACE AND SUCKS AIR
CAUSES SOLUTIONS
Too much/improper water flow through cleaner Check and adjust water flow per step 3, Figs. 7, 8, 9, 10
Improper tension on rear flap Turn rear flap adjuster to I
If still climbing too much, reduce water flow
until proper operation is achieved
Steering failure 1. Check and clean rear screen
2. Check to see that cone gear is free and
rotates smoothly in both directions
3. Check medium turbine and spindle gear
assemblies for malfunction
PROBLEM: CLEANER HEAD FLOATS
CAUSES SOLUTIONS
Cleaner head or return line has air in it Remove all air from cleaner head
Stop all air from entering the pool through
the return lines
If cleaner head and hose are covered with fine
bubbles, give the hose a good tug. This will release
the air bubbles and allow the cleaner head to settle
to the bottom of the pool until the hose is covered
with bubbles again
The cleaner head is being pulled or lifted off
the bottom of the pool by the cleaner hose
or return line flow – either at the surface or at
the bottom of the pool – or both
Readjust return lines to prevent water flow from
interfering with cleaner head and/or hose
STARZTRUCK AUTOMATIC POOL CLEANER TROUBLESHOOTING GUIDE

A. Pool plaster is affected by age, water chemistry, etc.
B. Pool plaster can deteriorate over a period of time.
C. The integrity of “good” pool plaster is such that a pool
vacuum cleaner – automatic or manual – cannot remove
that plaster.
D. The integrity of “good” pool plaster is such that the
plaster will cause wear on the StarzTruck automatic pool
cleaner – not vice versa.
E. Vinyl and fiberglass are affected by age, sunlight and
water chemistry.
F. Vinyl can become brittle and weak.
G. Vinyl can also be affected by the installation and the
pool’s surroundings.
H. When installing the StarzTruck automatic pool cleaner,
you assume all responsibility for the condition of the pool
and the pool’s surroundings.
To better serve you, please have the following information
available if you call AquaStar’s Technical Support Department:
1. The purchase date and purchase location of your
StarzTruck automatic pool cleaner.
2. The serial number of your StarzTruck automatic pool
cleaner.
3. The number of hose sections used.
STARZTRUCK AUTOMATIC POOL CLEANER TROUBLESHOOTING GUIDE
STARZTRUCK AUTOMATIC POOL CLEANER DISCLAIMER
PROBLEM: CLEANER STICKS AT STEPS, CORNERS, ETC.
CAUSES SOLUTIONS
Improper water flow Check and adjust water flow per step 3, Figs. 7, 8, 9, 10
Worn shoes Replace shoes
Worn wings Replace wings
Hose too short Install additional hose per installation instructions
Steering failure 1. Check and clean rear screen
2. Check to see that cone gear is free and rotates
smoothly in both directions
3. Check steering program and troubleshoot – then:
A. clean, repair or replace gearbox
B. check pod/A-frame connection and replace
if necessary – do not attempt to retighten
loose pods
C. check medium turbine and spindle gear
assemblies
877.768.2717 fax: 877.276.POOL (7665)
Outside the USA: +1.805.620.5060 fax: [phone]
www.aquastarpoolproducts.com [e-mail]

This limited warranty is only valid if the warranty card has been
filled out and returned with proof of purchase within allotted
time period. This limited warranty is extended to the original
purchaser (consumer) from the manufacturer of the StarzTruck
Automatic Pool Cleaner, AquaStar Pool Products, Inc.,
2340 Palma Drive, Warranty Dept. 104, Ventura, CA 93003, USA.
Phone [phone], outside the USA +1.805.620.5060.
AquaStar warrants this cleaner to be free from defects in
materials and workmanship for a period of one year from the
original date of purchase subject to all the following conditions
and exclusions.
1. Should the cleaner fail to be in good working order in
accordance with the above schedule, AquaStar will at its
option repair or replace the cleaner or any defective parts
at no additional charge except as set forth below. Repair
parts and replacement products will be furnished on an
exchange basis and will be new or functionally equivalent.
All parts removed as a result of replacement shall become
the property of AquaStar. Liability of AquaStar and the
sole remedy of the purchaser whether in contract under
any warranty, in tort (including negligence), in strict
liability or otherwise, shall be limited to the repair or
replacement of defective parts only and shall in no event
exceed return of the amount of the purchase price paid by
the purchaser.
2. This limited warranty is for the replacement of alleged
defective parts during the term of the warranty; owner
may ship the product by prepaid freight to AquaStar
Pool Products, Inc., 2340 Palma Drive, Warranty Dept.
104, Ventura, CA 93003, USA. Enclose a letter including
the serial number, date and place of purchase, name,
telephone number and address of owner, copy of purchase
receipt and a description of the problem. AquaStar, upon
determination and at our option, will repair and return
to the owner all defective parts that are covered by this
warranty. Any parts not covered by this limited warranty
will be returned to owner freight collect.
3. This limited warranty is only extended to the original
purchaser (consumer) and only during the time in which
the original purchaser occupies the premises where the
cleaner was originally installed. It does not apply to any
subsequent purchasers or recipients of the cleaner.
4. This limited liability warranty includes the replacement
of parts due to normal wear but does not include cosmetic
situations including but not limited to: discoloration or
fading due to sunlight or chemicals, scratches, scuffs, etc.
5. This limited warranty does not cover any loss, damage,
injury, or malfunction of the equipment due to the failure
to properly maintain and or operate the cleaner, or
alteration of the equipment, tampering, and act of God,
abuse, misuse, negligence, omissions.
6. This cleaner is intended for a properly designed and
maintained swimming pool. This limited warranty
does not cover pools that have a defective design, are
improperly maintained, and are inappropriate for the
StarzTruck automatic pool cleaner’s operation.
7. This limited warranty does not cover damage or injury
from improper installation, pump running dry, damage
due to loss of prime or plugged pipes.
8. This limited warranty does not cover any change in
appearance, damage, malfunction due to chemical
reactions, etc.
9. AquaStar is not responsible for any loss of time,
inconvenience or any consequential expenses such as
telephone calls, labor, etc., unless required by law.
10. Deterioration, discoloration or brittleness of pool plaster
and vinyl liners can be caused over time separately by
or in combination with, age and an imbalance in pool
water chemistry, improper installation and other factors.
AquaStar hereby disclaims any and all claims, and
purchaser releases AquaStar from any and all claims for
damages to any pool plaster or vinyl liner in purchaser’s
pool by reason of the use and/or operation of the cleaner.
11. This limited warranty is only valid in the USA and Canada.
12. This limited warranty is in lieu of any other warranties
express or implied, including the warranties of
merchantability or fitness. Any such implied warranty
imposed by state consumer law is limited in duration
to one year from date of purchase.
No distributor, dealer or representative has any authority to
make any warranties express or implied concerning StarzTruck
automatic pool cleaner except as contained herein. Unless
warranty card has been received by AquaStar, AquaStar reserves
the right to refuse repair service or to honor warranty.
STARZTRUCK AUTOMATIC POOL CLEANER LIMITED WARRANTY
877.768.2717 fax: 877.276.POOL (7665)
Outside the USA: +1.805.620.5060 fax: [phone]
www.aquastarpoolproducts.com [e-mail]

FIRST NAME LAST NAME
COMPANY NAME (IF POOL SERVICE OR BUILDER)
ADDRESS
CITY STATE ZIP CODE
PHONE FAX
EMAIL
COMMENTS
1. Serial number (found on bottom of cleaner)
___________________________________________________________________
2. Type of pool:
oVinyl
oFiberglass
oGunite
oOther
3. Cleaner model:
oConcrete
oVinyl/fiberglass
4. Date of purchase: __________________________________
5. Name of dealer/builder/service professional where
purchased: _________________________________________
6. Pool is _______________ years old.
7. What cleaner is this replacing?
______________________________________________________
8. Are you a:
oConsumer
oPool Service Technician
oPool Builder
oOther
Include a copy of your receipt and return this form within 15 days of purchase. The additional information requested is to help us
understand our customers. The information is NOT sold or shared with any other party. Thank you for your purchase.
WARRANTY REGISTRATION CARD
Please complete and mail with receipt to:
AquaStar Pool Products, Inc.
Warranty Registration Dept. 104
2340 Palma Drive
Ventura, CA 93003
Or fax to:
877.276.POOL (7665)
Outside the U.S.: +1.949.336.1940