Aquatica Digital AquateX Lullaby Mini User manual

www.aquaticabath.com
E: [email protected]
Lullaby Mini
AquateX™Bathtub
(formerly Aquastone™)
Installation & Care Manual
USA & Canada

www.aquaticabath.com
E: [email protected]
Lullaby Mini
AquateX™ Bathtub
55.125”
Ø2.0”
Use Male Adapter Spg x MIPT
- ABS DWV for Aquatica®bath wastes
with Sch40 Waste Fitting
Thread 1½ NPSM ( 1½ IPS)
P-Trap
(not supplied)
Male Adapter Spg x MIPT - ABS DWV
for Aquatica®bath wastes with
Sch40 hub outlet.
Thread: 1 ½ NPSM (1 ½ IPS)
Male Adapter Spg x MIPT - ABS DWV
for Aquatica®bath wastes with
Sch40 hub outlet.
Thread: 1 ½ NPSM (1 ½ IPS)
Aquatica®Freestanding
Bath Installer™
(not supplied)
Sch40
Waste Fitting
1½“ flanged brass
tube for Aquatica®
cable-drive and
concealed bath
wastes.
PLEASE NOTE: Parts marked with are supplied as part of Aquatica®Freestanding Bath Installer™ Kit (NOT included with bathtub)
13.75”
0.375”
25.625”
17.50”
27.50”
2.00”
MaleAdapter Spg x MIPT - ABS DWV
forAquatica®bath wastes with
Sch40hub outlet.
Thread:1 ½ NPSM (1 ½ IPS)
MaleAdapter Spg x MIPT - ABS DWV
forAquatica®bath wastes with
Sch40hub outlet.
Thread:1 ½ NPSM (1 ½ IPS)
MaleAdapter Spg x MIPT - ABS DWV
forAquatica®bath wastes with
Sch40hub outlet.
Thread:1 ½ NPSM (1 ½ IPS)
A
A
A - A
3.125”
52.375”
41.50”
39.125”
18.875”
16.25”
23.75”
Slope: 0.25” - 0.50” per foot

MaleAdapter Spg x MIPT - ABS DWV
forAquatica®bath wastes with
Sch40hub outlet.
Thread:1 ½ NPSM (1 ½ IPS)
MaleAdapter Spg x MIPT - ABS DWV
forAquatica®bath wastes with
Sch40hub outlet.
Thread:1 ½ NPSM (1 ½ IPS)
MaleAdapter Spg x MIPT - ABS DWV
forAquatica®bath wastes with
Sch40hub outlet.
Thread:1 ½ NPSM (1 ½ IPS)
12
HANDLE
WITH CARE
DO NOT
DROP
The Male Adapter Spg x MIPT - ABS DWV for Aquatica®bath wastes with Sch40 Waste Fitting
and Aquatica®Freestanding Bath Installer™ are not included with bathtub.
Male Adapter
Spg x MIPT
- ABS DWV
- available for
purchase separately
1 ½ " flanged
brass tube - available for
purchase separately
Sch40
Waste Fitting
Aquatica®
Freestanding
Bath Installer™
in the floor
- available for
purchase
separately
P-Trap - not
included
!
!
4
Installation is completed by applying
silicone at several points between
the bottom panel and floor.
3
Lullaby Mini
AquateX™ Bathtub

www.aquaticabath.com
E: [email protected]
TYPICAL FREESTANDING BATHTUB INSTALLATION PROCEDURE
Before you start:
• Ensure that the floor is even.
• The waste-overflow fitting is supplied with the product, however other accessories like the slip joint
and adaptors are not included and must be purchased separately.
• Because of the technical features of the product, it should be used only with the supplied waste-
overflow or specific 3rd party models that have been tested and approved by us.
• Place the bathtub by raising it up 4” with 4x4 pieces of lumber so you can have access from the
bottom of the bathtub.
INSTALLATION SEQUENCE
• The Lullaby Mini bathtub is equipped with factory pre-installed overflow system.
• The waste pipe/p-trap connection must be made directly to the waste/drain outlet located
at the bottom of the tub.
• Picture 1-2: the bathtub is leveled via a water level at the intended local installation area.
• Picture 3: place the bathtub by raising it up 4” with 4x4 peices of lumber so you can have access
from the bottom of the bathtub. Important note: during the installation, the bathtub should not be
turned on its side to prevent its weight from deflecting its monobloc sides. This is why it is important
to use supports to raise the bathtub above the floor. This will also provide you with easy access to the
internal plumbing parts.
Lullaby Mini
AquateX™ Bathtub
1 2 3

Lullaby Mini
AquateX™ Bathtub
INSTALLATION SEQUENCE continued
• Picture 4: the water outlet pipe should be connected.
• Picture 5: foot leveling lock nuts are adjusted.
• Picture 6: silicone is applied to the feet of the bathtub that stands on the floor.
• Picture 7: when the installation is completed, the bathtub is taken down from the supports
( ie 2 x 4x4's). If necessary, installation is completed by applying silicone at several points between
the bottom panel and floor.
Compatible adaptors for adapting a threaded male connection to a solvent weld connection:
• Mueller Industries: Part # 05913
Or
• Nibco: C4803
http://www.homedepot.com/p/NIBCO-1-1-2-in-PVC-DWV-Hub-x-FIPT-Female-Adapter-C4803HD112/100677994
The adaptor must have the appropriate thread type or it will keep slipping and you will not be able to get
a tight connection!
Male Adapter Spg x MIPT - ABS DWV
for Aquatica®bath wastes with
Sch40 hub outlet.
Thread: 1 ½ NPSM (1 ½ IPS)
45
76
Use Male Adapter
Spg x MIPT
- ABS DWV for Aquatica®
bath wastes with
Sch40 Waste Fitting
Thread 1½NPSM
(1½IPS)
Please refer to our
kit installation guide
on page 6