Aquatica Digital Baby Boomer User manual

Installation & Care Manual
Aquaticausa.com
Aquaticabath.ca
E: [e-mail]
USA / Canada
Corner Walk-In Bathtub
Baby Boomer™

Aquaticausa.com
Aquaticabath.ca
E: [e-mail]
Baby Boomer™
Corner Walk-In Bathtub
P-Trap (not supplied)
Aquatica®
Freestanding
Bath Installer™
(not supplied)
1 ½” flanged brass
tube for Aquatica®
cable-drive and
concealed bath
wastes.
PLEASE NOTE: Parts marked with are supplied as
part of Aquatica® Freestanding Bath Installer™ Kit
(NOT included with bathtub)
Use “1 1/2” PVC or ABS Female Adapter
(use of PVC or ABS depends on your local or state
plumbing codes) Hub x FIPT
The ABS or PVC female adapter features a hub x female NPT
thread connection and provides a means for adapting a solvent
weld connection to a threaded connection.
Home Depot PART
1 1/2” ABS
Female Adapter
Hub x FIPT
3'-1 1/5"
3'-5 1/6"
1'-7 2/3"
9"
7 5/6"
2'-2"
3'-8 1/10"
2'-2 2/5"
2'-5 1/2"
Scario vasca 1" 1/2
1" 1/2 drain
4'-3 1/5"
8 5/6"
2'-7 1/2"
1'-3 3/4"
PARTS LIST
MEASUREMENTS: inches

Baby Boomer™
Corner Walk-In Bathtub
TYPICAL FREESTANDING BATHTUB INSTALLATION PROCEDURE
Before you start:
•Ensure that the floor is even.
•The waste-overflow fitting is supplied with the product, however other accessories like the slip joint and
adaptors are not included and must be purchased separately.
•Because of the technical features of the product, it should be used only with the supplied waste-overflow
or specific 3rd party models that have been tested and approved by us.
•Place the bathtub by raising it up 4” with 4x4 pieces of lumber so you can have access from the bottom
of the bathtub.
•The bath must rest on its feet, not the monobloc sides. The feet must be adjusted to compensate for any
floor imperfections and leave minimal gap with floor.
INSTALLATION SEQUENCE
•The Aquatica™ bathtub is equipped with factory pre-installed overflow system.
•The waste pipe/p-trap connection must be made directly to the waste/drain outlet located at the bottom of the tub.
•Picture 1-2: the bathtub is leveled via a water level at the intended local installation area.
•Picture 3: place the bathtub by raising it up 4” with 4x4 pieces of lumber so you can have access from the bottom of
the bathtub. Important note: during the installation, the bathtub should not be turned on its side to prevent its weight
from deflecting its monobloc sides. This is why it is important to use supports to raise the bathtub above the floor.
This will also provide you with easy access to the internal plumbing parts.
2 31

Aquaticausa.com
Aquaticabath.ca
E: [e-mail]
Baby Boomer™
Corner Walk-In Bathtub
min. 2'
min. 2'
min. 7'-6"
min. 7'-6"
WARNING
Electrical appliances (plug, switches, lamps, etc.) must be placed or installed at the minimum safety
distance of 2' and a height of 7'-6".
INSTALLATION

Baby Boomer™
Corner Walk-In Bathtub
1
2
3
Take the tub out of the packaging taking care to hold
it from the bottom edge of the tub. Lie it near the
place where it will be installed.
If not already prepared install the faucet on the
bathtub. See the instructions in the faucet box.
Remove the panel by unscrewing the three retaining
screws at the base and sliding it downwards.
INSTALLATION continued

Aquaticausa.com
Aquaticabath.ca
E: [e-mail]
Baby Boomer™
Corner Walk-In Bathtub
4
5
6
If not already prepared, assembly the drain and
distribution column following the instructions in the box.
Connect the distribution to the diverter of the taps
The tub is set by the factory with a height at the top
edge of 3'-1 4/5".
At this stage it is not important if the tub does not stand
perfectly on the ground, the adjustment will be done
later.
The bathtub stands on 6 adjustable feet. The
leveling must be carefully adjusted for the correct
functioning of the tub.
WARNING
An incorrect execution of these adjustments may
cause a not perfect sealing of the door.
First feet 2 and 5 are raised from the ground.
Operate on feet number 1,3,4 and 6 to adjust the
level.
INSTALLATION continued
3'-1 4/5"

Baby Boomer™
Corner Walk-In Bathtub
7
8
9
Place the tub in the installation corner and level it
perfectly using the feet 1,3,4 and 6.
CAUTION To level the tub, act only on the feet
and not on the threaded rods. It is important that
all levelling feet are completely touching the floor
and that the level is perfect for the door system
to work properly.
Once the optimal positioning is achieved, stop the
feet by acting on the nut of each foot. Now adjust
the feet 2 and 5 to touch the floor, without forcing.
Stop the feet by acting on their nut.
WARNING
The feet 2 and 5 must not lift any of the
previously adjusted feet otherwise it should
compromise the stability of the tub and above all
the door system would not work properly.
Connect the drain of the tub to the ground
predisposition as indicated on the technical
details.
Connect the taps to the wall arrangement as
indicated on the techincal details.
INSTALLATION continued

Aquaticausa.com
Aquaticabath.ca
E: [e-mail]
Baby Boomer™
Corner Walk-In Bathtub
10
INSTALLATION continued
All tubs are individually 100% water tested at the factory in
order to ensure their perfect functioning. During this phase
of the installation it is necessary to test the product in order
to verify that all the adjustments made at the factory have
been maintained. Due to improper transport or assembly, in
some cases there may be leaks.
A) Leak at the base: it will be necessary to screw the rear
nut to the column, bringing it against the plate mounted on
the tub. Screw the outer nut half a turn at a time until the
leak is resolved. Screw the rear nut to the column again.
With this operation we have opened the front side
B) Leak on the high side: it will be necessary to unscrew
the front column nut half a turn at a time and do the same
on the rear nut until the leak is resolved. With this operation
we closed the front side
WARNING The adjustments must be minimal in order to
avoid creating contrary sealing problems.
At the end of each adjustment, the two nuts must always
be tightened to the column.
In case of leaks, in the lower part or along the
edge near the closing handle, only with a perfect
installation as previously described, it will be
possible to act on the tub shape by opening or
closing the front side. For this aim, on the front
frame, there is a column with an adjustment on
the head formed by a plate with threaded rod
screwed to the tub and two nuts, one placed on
the front and one on the back. This system is able
to slightly change the closure.
Plate
Centrally mounted
Adjustment
front nut
rear nut

Baby Boomer™
Corner Walk-In Bathtub
13
14
To stop the panel, insert it under the edge of the tub, between the edge itself and the thrust springs. Use
the supplied wedges to help you.
Replace the previously removed screws at the base of the panel.
Remove the wedges used as a riser.
INSTALLATION continued
Insert the panel under the tub again, starting from the front side, then under the door and then under the
short side.

Aquaticausa.com
Aquaticabath.ca
E: [e-mail]
Baby Boomer™
Corner Walk-In Bathtub
FEATURES
• 18 Gauge Epoxy coated Metal Deck Flange
• Designed to be installed in an 8” joist space
• Can be installed with Waterproofing Membrane
(*bronte™ NobleSeal TS Recommended)
• CSA Certified for Canadian and US markets
KIT INCLUDES
• 2 Brass Tailpieces (Fine Thread and Flanged)
• Freestanding Bath Installer™ assembly with 1-1/2” DWV
ABS tailpiece
• Cutting templat e
INSTALLATION TIPS
• Use 5” hole saw to cut sub floor (not included).
Cutting template included
• Do not cut the brass Tailpiece as this may cause a leak
• Secure Deck Flange with 6 screws (not included)
44"
121mm
127mm
28"
28"
1"
27mm
3-7/8”
[ 98mm ]
8"
11
2"
Fine Thread Tailpiece
Attaches to 314 Series
Direct/Offset Bath Wastes
and Integral Bath Wastes.
11
2"8"
Flanged Tailpiece
Attaches to 314DC Series
Cable-Drive
® Bath Wastes
and Integral Bath Wastes.
ABS or PVC Adapter Kit
Attaches to ABS or PVC Bath
Wastes and includes Brass
Nut and Poly Washer.
18"
41mm
1
4"
7"
178mm
1
4"
Y
X

Baby Boomer™
Corner Walk-In Bathtub
INSTALLATION INSTRUCTIONS
Attaches to Freestanding Bath W/O
A. Cut 5” hole into wood sub-floor
(use supplied Cutout Template).
B. Measure and cut ABS Tailpiece as necessary
to ensure a secure connection to P-Trap below.
C. Insert Freestanding Bath Installer™ assembly into floor
opening and connect to Pipe below.
D. Affix to sub-floor with 6 screws (not supplied)
A. Install flooring surface, leaving a 5” opening to
access Drain.
B. Affix the appropriate brass Tailpiece to the Waste &
Overflow. NOTE: DO NOT CUT THE BRASS TAILPIECE
AS THIS MAY CAUSE A LEAK.
Ensure the measurement between the base of the
Drain and P-Trap will accomodate the Tailpiece.
Other lengths available (contact Aquatica).
A. Cut out the Installation Label with a utility knife and
remove to expose the Drain.
B. Apply lubricant (supplied) to the Tailpiece.
C. Position the Tub and brass Tailpiece in-line with the Drain.
D. Carefully lower the tub with the installed brass Tailpiece
into the Red Collar in Drain assembly. Ensure Tailpiece is
fully engaged with Seal.
IMPORTANT: Do not remove Installation Label until Step 3.
DO NOT CUT THE SUPPLIED BRASS TAILPIECE. Doing so may cause a leak.
Disassembling the drain or cutting the Tailpiece will void the warranty.
1
2
3

Aquaticausa.com
Aquaticabath.ca
E: [e-mail]
Maintenance Instructions
The smooth surface of your Aquatica®
Acrylic Bathtub accumulates hardly any
dirt, and can be maintained by simply cleaning
with a soft cloth, using a mild detergent in
water, then wiping over with a dry cloth.
Avoid using abrasive cleansers or solvents,
which will cause damage to the surface.
Damage caused by use of these products, or
any other inappropriate treatment, is not
covered by our guarantee.
Инструкция по уходу
Поверхность легко чистится. За счет
гладкости грязь к ней не прилипает. Для
регулярного ухода используйте мягкую
ткань, мыльный раствор и воду. После
чистки вытирайте поверхность сухой тканью,
которая хорошо впитывает влагу.
Не используйте губки с абразивной
поверхностью и агрессивные растворители,
которые могут повредить ванну.
Повреждения, возникшие вследствие
неправильного ухода, не покрываются
гарантией.
Installation & Entretien
Cette surface est facile à entretenir et à nettoy-
er. Sa surface particulièrement lisse, ne retiens
que très peu la saleté. Un entretien quotidien
nécessite simplement l’utilisation d’un chiffon
doux, de l’eau et un peu de savon. Essuyer
avec un chiffon sec. L’utilisation de détergents
ou de solvants endommageraient cette surface.
Les dommages resultants d’un traitement non
conforme effectué par l’utilisateur sont exclus
de la garantie que nous offrons.
Manuale per il corretto mantenimento
La superficie necessita di pulizia ed
accorgimenti per il corretto mantenimento.
Una superficie liscia non accumula lo sporco.
Usare una spugnetta con del detergente non
aggressivo per una pulizia regolare. Asciugare
con un panno. Evitare l’uso di solventi o
materiali abrasivi: potrebbero rovinare la
superficie.
Un danno causato da trattamento inappropriato
non verra’ coperto dalla garanzia.
Instrucciones para la correcta manutención
La superficie debe de ser limpiada y
adecuadamente mantenida. Una superficie lisa
no acumula suciedad.
Utilice una esponja con un detergente suave
para la limpieza diaria. Seque con un paño.
No utilice disolventes o materiales abrasivos
ya que podrían dañar la superficie.
Los daños causados por el tratamiento
inadecuado no serán cubiertos por la garantía.
True Ofuro - Maintenance Instructions
True Ofuro - Инструкция по уходу
True Ofuro - Installation & Entretien
True Ofuro - Manuale per il corretto mantenimento
True Ofuro - Instrucciones para la correcta manutención