Manual Mode
In Manual Mode you set the intensity of the light for constant operation.
Once the unit is switched on, select Manual Mode. Brightness of Group A
(white) and Group B (red, green, blue (RGB)) lights will be displayed on
LCD screen.
Press and immediately release the button to switch between and select
either Group A or Group B (figure 4.1).
Slide the button to the left or right to adjust the brightness. After 6
seconds without operation, the unit will automatically exit the menu and
save the set brightness.
Automatic Mode
In Automatic Mode, you set the time the light stays on (6-9-12-18 hours) and the
intensity.
Once the unit is switched on and in automatic mode, slide the button to the left or
right to highlight either "TIME" or "TIMING". Pressing the button and then
immediately releasing will select the highlighted menu option (figure 5.1/5.2). The
unit will automatically exit the menu after 2 seconds without operation.
Figure 5.1 Figure 5.2
To adjust TIME: press and immediately release the button when TIME is
highlighted to enter the time setting interface (figure 5.3). Slide the button left or
right to select correct time. Press and immediately release the button to switch
between hours and minutes. Press and hold button to return to previous menu.
Figure 5.3 Figure 5.4
To adjust TIMING: on the interface of figure 5.2, press and immediately release
the button to enter the interface seen below in figure 5.5.
Slide the button left or right to select the time in hours that the light will remain
on daily: 6H →9H →12H →18H. For example, if 6H option seen in figure 5.5 is
selected, the light will remain on for 6 hours from when this selection was made.
The light will come on at the same time and turn off 6 hours later each day.
Press and hold button to return to the interface figure 5.1.
Figure 5.6 shows the display for the light settings in automatic mode. In the top
left, T:6H, shows that the 6 hour setting has been set at 100% on Group A (white)
LEDs and 100% on Group B (RGB) LEDs.
The display will flick between figure 5.6 and 5.7 when the unit has been left
untouched for more than 6 seconds.
Press and immediately release the button to highlight A:100% and slide button
from left to right to adjust brightness of group A (white) LEDs. Press button to
change to control group B (RGB) LEDs.
Custom Mode
In Custom Mode, you can set the unit to simulate a sunrise and sunset by
programming the intensity of 7 different time points.
See Setting Time instructions in Automatic mode to set time. Press the button when
time is highlighted to change the time of the internal clock on the unit (figure 6.1).
Figure 6.1 Figure 6.2
On the interface of figure 6.1, press and immediately release the button to enter
the program menu seen in figure 6.2. Push the button to the left or right to set the
time points 1 to 7 (TP1-TP7).
Figure 6.3 Figure 6.4
On the interface of figure 6.2 in TP1, press the button to highlight the time, as
seen in figure 6.3. Push the button to the left or right to set the time for the
selected time point. Press and immediately release the button to highlight the
brightness for the selected time point. Push the button left or right to change the
brightness of group A (white) LEDs. Push the button and immediately release to
control the brightness of group B (RGB) LEDs. (Figure 6.4) Repeat this for as
many of the 7 time points that you wish to use. This will enable you to change the
brightness of the light at any time throughout the day.
When on the interface shown in figure 6.3 and 6.4, press and hold the button to
return to the Custom Mode initial interface (figure 6.1). After 6 seconds without
operation, it will automatically exit and save the data. The unit will then carry out
the set programming.
Figure 6.5 Figure 6.6
If the unit is left without use on custom mode, it will flick between the interfaces
shown in figure 6.5 and 6.6. Press and hold the button to exit this operation
interface to return to the Custom Mode initial interface (figure 6.1).
AQUAVIVO recommends the following custom mode settings:
Warranty
AQUAVIVO provides a 36 month limited warranty to the original purchaser of its
products against all defects in original workmanship and material, under normal
use and service. The following exceptions apply:
1. Damage caused by water intake.
2. Defects attributed to accident, abuse, or incorrect maintenance and
storage.
3. Defects resulting from disassembly or modification by customers or
repairers of other companies.
4. Defects caused by damage to the shell or other external components
during usage.
5. The machine label numbers are torn, blurred or counterfeit.
6. Defects caused by natural disasters (such as earthquakes, fires,
floods, etc).
