AQUOR House Hydrant V1+ User manual

www.aquorwatersystems.com
[phone]
Aquor®House Hydrant V1+
ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED
3
Aquor House Hydrant V1+
The Aquor House Hydrant is a flush-mounted
hydrant with twist-lock connection system designed
for outdoor use.
The hydrant is intended to be installed in the exterior
walls of homes and buildings. Upon disconnection, a
small amount of water self-drains from the outlet. The
Aquor hose connector has a built-in vacuum breaker
for code approved anti-siphon protection.
INCLUDED IN THIS KIT
x1 Stainless Steel Hydrant
x1 Hose Connector (CN-VB2)
x1 Debris Cover
x3 #10 1.5" Mounting Screws
OVERVIEW
Overview
Read this entire instruction sheet before installing to ensure proper
installation. The information in this manual is subject to change
without notice.
Hydrant can only provide freeze protection when disconnected and
allowed to drain.
Intended for irrigation use and outdoor watering. Shall not be
subjected to more than (12) hours of continuous water pressure as
directed by ASSE code requirements.
Installation shall be in accordance with AS/NZS 3500 series of
standards.
Installation must comply with local codes and ordinances.
Please leave this manual with the property owner after completing the
hydrant installation.
FEATURES & BENEFITS
• Instant water access in less than a second,
even under full water pressure.
• Hydrant automatically self-drains upon
disconnection to provide freeze protection.
• Stainless steel operating rod and pressure
closed valve provide zero-maintenance
reliability for years.
• Robust O-ring connection system ensures a
reliable leak-proof seal, even at high water
pressures.
• Low-profile design sits flush against wall.
• Hydrant comes standard with ” NPT (f) inlet.
Optional rotatable 90° elbow inlets available.
• Attach any ” accessory (e.g. water timers,
splitters, regulators) to end of hose connector.
• Hose connector contains vacuum breaker for
code approved anti-siphon protection.

www.aquorwatersystems.com
[phone]
Aquor®House Hydrant V1+
ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED
5
. PREPARE WALL
Determine the location for the hydrant. The
hydrant’s inlet must be installed into a heated area
of the structure that will not drop below freezing.
Before installation, make sure there is adequate work
room for securing the hydrant to the supply line.
Prepare the mounting surface and entry hole.
Aquor®House Hydrants require a vertical and
smooth mounting surface to ensure proper
installation and draining. Depending on the exterior
wall surface, a mounting block may be required
to provide a vertical and smooth mounting spot.
Mounting blocks can be
commonly found in hardware
stores, or can be made
on-site with materials such
as wood, fiber-cement, or
PVC trim board. Aquor®
mounting blocks can be
found on our website.
Installation
. SECURE HYDRANT TO WALL
Pre-pilot the mounting holes. Make sure to insert the
debris cover wedge behind the hydrant faceplate for
accurate markings.
Using a 1” hole saw, bore the entry hole through
the wall (and mounting block if using one) in the
desired location.
Tip: If enlarging an existing hole, try
cutting a dowel of the appropriate size
to use as a guide for the hole saw.
Tip: Use a low speed setting or a hand screwdriver
to avoid stripping the fasteners.
INSTALLATION
If drilling through a deep wall, you may
need to accommodate for the hydrant’s
downward angle.
O 1/” (39 mm)

www.aquorwatersystems.com
[phone]
Aquor®House Hydrant V1+
ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED
7
. ATTACH FITTING
Proceed to the interior of the wall. Before attaching
a fitting, unscrew the hydrant’s rear inlet from the
main hydrant body.
The hydrant’s default inlet is ” NPT (f). Other
optional inlet styles are available.
Thread in the appropriate ” NPT fitting for your
plumbing type, wrapped in teflon tape then pipe-
joint compound. Firmly tighten with a wrench.
Tip: Drilling into brick or stone? Consider using
specialized fasteners and/or anchors. We also
manufacture optional stainless steel mounting plates
to space the mounting holes out further if needed.
With the cover wedge behind the faceplate flange
secure the hydrant to the wall. x3 #10 1.5" stainless
steel screws are provided.
After securing, test the cover to make sure it opens
and closes properly.
Cover wedge
behind faceplate Tip: The inlet is on an O-ring seal. It’s designed to
rotate up to one turn while still keeping a watertight
seal. This is useful for alignment, especially for the
optional 90° elbow inlets. Tighten the inlet until it
stops, then rotate back to the desired spot. This seal
is rated to 250 PSI.
. CONNECT TO PLUMBING
With the appropriate fitting threaded in, connect the
hydrant to your plumbing system.
Hand-tight is fine; do not over-torque the
hydrant’s body connection. Do NOT apply
teflon tape or any kind of sealant to the
hydrant’s body threads.
With the appropriate fitting installed, re-attach the
inlet to the hydrant body.
INSTALLATION

www.aquorwatersystems.com
[phone]
Aquor®House Hydrant V1+
ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED
9
Depending on the type of plumbing, it will vary how
the hydrant connects. Common ways of connecting
to copper plumbing include soldering and push-fit
adapters.
Tip: With PEX tubing, we recommend adding an
expansion loop inside the wall if possible. This
allows the entire hydrant and fitting assembly to
be inspected and serviced from the exterior of the
building, if ever needed.
Common ways of connecting to PEX include crimp
rings, expansion tools, and push-fit adapters.
Before plugging in, attach a garden hose to
the Aquor®hose connector.
Complete the installation by turning on the water
supply.
Tip: With copper plumbing, consider securing the
hydrant's inlet against a stud. This way the hydrant
can be removed from the building's exterior if ever
needed. The hydrant faceplate and body can be
rotated out and re-attached to the inlet.
Use a closed-end, such as a nozzle, on the hose
to create back pressure. Connect to the hydrant
and water should pressurize the hose immediately.
Disconnect and ensure the hydrant drains, then
remains leak-free.
Inspect the hydrant and plumbing connections for
any leaks.
INSTALLATION & OPERATION
Operating Aquor® House Hydrants is a simple
process. Water starts flowing through the hydrant
when the hose connector is plugged in. Turn o the
hydrant by unplugging the hose connector.
Attach the Aquor®hose connector to any garden
hose. It can stay attached; there is no need to
remove it every use. Before storage, depressurize
your hose by squeezing the nozzle on the other end.
Always remove hose during freezing
temperatures.
Operation
Use any accessory as you would with a traditional
bib. Inline ball valves, timers, splitters, vacuum
breakers, and etc. can be attached to the connector.
Aquor®Hose Connector
Ball Valve (optional)
Garden Hose
Some Aquor®hose connectors have a
one-way check valve to prevent water
from spraying when you disconnect.

www.aquorwatersystems.com
[phone]
Aquor®House Hydrant V1+
ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED
11
Connect: Line up the three helical grooves on the
hose connector with the three nibs on the hydrant
faceplate. Simultaneously push and twist the
connector clockwise in a smooth motion. Make sure
to align the grooves fully and push in before twisting.
Water flow will start instantly when the connector is
engaged (see image below).
Disconnect: Push the connector in slightly, then
untwist counter-clockwise (see image below). The
hydrant will self-drain any remaining water left in the
body and vacuum breaker assembly. The water will
drain for the few moments, this is perfectly normal.
Remember to depressurize your hose before storage.
It’s best to disconnect the hydrant when not in use.
For the longest lifespan, store your Aquor® hose
connectors out of the elements.
Connect
Disconnect
OPERATION
Tip: If you leave the Aquor®connector attached to
your garden hose, make sure to depressurize the
hose after use. Temperature changes can cause
water inside to expand, causing excessive pressure
on the connector’s internal check valve (and your
nozzle or accessories) over time.
For installation or other technical questions, please
call our customer service team at [phone].
Don't get wet!
Remember to attach
a garden hose here
before engaging the
hose connector.

www.aquorwatersystems.com
[phone]
Aquor®House Hydrant V1+
ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED
13
Aquor®hydrants leave the factory fully tested and
operational. They are treated with an FDA approved
lubricant where needed. The hydrant requires no
scheduled maintenance to provide a long operational
life. If a problem does arise, all the serviceable
components are oered in repair kits.
It’s best to disconnect the hydrant when not in use.
The hydrant can only oer freeze protection when
disconnected. We recommend unplugging after each
use.
For freeze protection, the hydrant does not need
to be covered any further. As long as it has been
disconnected, allowed to drain, and the ambient
temperature inside the wall remains above freezing,
the hydrant and the plumbing will be protected.
Storing your hose connectors out of the elements can
prolong their lifespan. You can drain your hose and
bring it inside - the internal check valve prevents any
unwanted draining afterwards, so your floor stays
dry.
Protect the hose connector’s O-rings. They are
designed for extremely long lifespans if used
properly. Use care not to snag the connector O-rings
on the hydrant nibs. When connecting, line up the
grooves before attempting to push or twist.
Maintenance
MAINTENANCE
Routine cleaning with soap and water is usually
sucient to maintain the corrosion resistance and
appearance of the marine-grade stainless steel. Use
a soft brush to remove any accumulated dirt, then
rinse with clean water. Use stainless steel polish as
needed.
If you have hard water buildup, the hydrant can be
completely disassembled for service or cleaning
if needed. The inner valve and stem are accessed
through the rear.
We recommend replacing the internal valve once
every 20 years, or as needed. You may periodically
clean and lubricate the O-ring if there is mineral
buildup.

www.aquorwatersystems.com
[phone]
Aquor®House Hydrant V1+
ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED
15
Debris Cover
7. Debris Cover Gasket
8. Debris Cover Wedge
9. Debris Cover Nut & Bolt
10. Debris Cover
Hydrant
1. Rear Valve Housing (inlet)
2. Valve Return Spring
3. Hydrant Body O-Ring
4. Main Valve O-Ring
5. Operating Rod
6. Hydrant Body
Parts Description
123
5
4
11 12
A
A
B
PARTS DESCRIPTION
Hose Connector
11. Connector O-Rings
12. Connector Body
6
7
8
9
10
Need Parts? Stem Replacement Kits available in 2”, 4”, 6”,
8”, 10”, and 12” and Hose Connector O-Ring Kits
are available.
For help, email us at [e-mail]
or call us at [phone].
B
AB

www.aquorwatersystems.com
[phone]
Aquor®House Hydrant V1+
ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED
17
Technical Specs
TECHNICAL SPECS
In the Box
Backflow Protection
Inlet x Outlet
Operating Temperature
Operating Water Pressure
Flow Rate
Plumbing Compatibility
Hydrant Material
Connector Material
O-Ring Material
Cover Material
Certifications
Warranty
SKU
SKU
HHP002
HHP004
HHP006
HHP008
HHP010
HHP012
Stem Length (A)
2” Hydrant
4” Hydrant
6” Hydrant
8” Hydrant
10” Hydrant
12” Hydrant
Overall Length (B)
3 /” (92 mm)
5 /” (146 mm)
7 /” (197 mm)
9 /” (248 mm)
11 /” (298 mm)
13 /” (349 mm)
Optional 90° elbow inlets reduce overall length by 1/2”(13 mm).
Hydrant, Debris Cover, Hose
Connector, x3 #10 Mounting
Screws, Install Instructions
Yes, built-in vacuum breaker
1/2 “ NPT (f) x 3/4” GHT (m)
33 -140 °F
25-125 PSI
6.8 GPM @ 52 PSI
All (PEX recommended)
316L Stainless Steel
Acetal Resin Polymer
Fluorocarbon Rubber
ASA Thermoplastic
ASSE 1019C, ASME A112.18.1,
CSA B125.1, AS/NZS3718
10 Years stainless steel,
5 Years polymer
HHP002, HHP004, HHP006,
HHP008, HHP010, HHP012

www.aquorwatersystems.com
[phone]
Aquor®House Hydrant V1+
ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED
19
HHP
STEM LENGTH: "
OVERALL LENGTH:  - /"
Close-Couple House Hydrant V1+
HHP
STEM LENGTH: "
OVERALL LENGTH:  - /"
4" House Hydrant V1+
TECHNICAL SPECS

www.aquorwatersystems.com
[phone]
Aquor®House Hydrant V1+
ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED
21
HHP
STEM LENGTH: "
OVERALL LENGTH:  - /"
6" House Hydrant V1+
HHP
STEM LENGTH: "
OVERALL LENGTH:  - /"
8" House Hydrant V1+
TECHNICAL SPECS

www.aquorwatersystems.com
[phone]
Aquor®House Hydrant V1+
ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED
23
HHP
STEM LENGTH: "
OVERALL LENGTH:  - /"
10" House Hydrant V1+
HHP
STEM LENGTH: "
OVERALL LENGTH:  - /"
12" House Hydrant V1+
TECHNICAL SPECS

www.aquorwatersystems.com
[phone]
Aquor®House Hydrant V1+
ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED
25
Troubleshooting
PROBLEM
No water flow when connected.
Water leaking from plumbing connection.
Water leaking from hydrant body-to-inlet connection.
TROUBLESHOOTING
SOLUTION
First you’ll want to identify whether the issue is in the
hydrant of the hose connector.
Make sure water supply is live to the hydrant. Try
depressing the hydrant valve with your thumb to test
for pressure. If the water pressure is live, the issue is
likely the hose connector.
Inspect the hose connector to see if the internal check-
valve is stuck. In variable weather conditions, if left
pressurized outside, water expansion may cause the
check valve to seize.
If the hose connector has a ball-valve, make sure it is on.
For threaded fittings, re-wrap with 4-5 wraps of teflon
tape, followed by a layer of pipe-joint compound.
Firmly tighten with wrenches.
For PEX specific fittings, ensure a compatible PEX
tubing type and installation tool are being used. Check
fitting dimensions for spec.
Inspect the O-ring between the rear valve housing (inlet)
and hydrant body. The inlet can be backed o up to
on full rotation without losing a watertight seal. Ensure
no teflon tape or sealant is applied. Inlet should thread
smoothly.

www.aquorwatersystems.com
[phone]
Aquor®House Hydrant V1+
ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED
27
Water leaking from the hydrant main outlet when
disconnected.
Water leaking from vacuum breaker when connected.
Water sprays from the vacuum breaker when
connecting.
Hose connector won’t stay plugged in.
Water leaking from the hydrant main outlet (front) when
connected.
PROBLEM
A slow leak may indicate a stuck or bent internal rod, or
damaged O-ring.
First, try to reset the valve from the front. Shut-o water
supply and use needle nose pliers to press in and rotate
the internal operating rod. Resistance could indicate a
piece of debris behind the valve.
If leak persists, remove the internal operating rod from
the hydrant by unscrewing the rear inlet from the body.
Inspect the O-ring and stem for any damage, remove
debris or replace assembly if needed.
First, ensure water pressure is between 25-125 PSI.
Pressure that is too high or too low can cause issues
with backflow preventers.
Next, test with a second hose connector. If the issue
persists, replace the faulty hose connector.
A small burst of water when connecting or disconnecting
is normal due to pressure.
If the spray or leak persists, inspect the vacuum breaker
washer and replace if needed.
Ensure water pressure is not too low. The hydrant uses
water pressure to seal, and is designed for pressures of
25-125 PSI. If you are installing the hydrant on a well
or low-pressure system, contact us for a higher weight
hydrant valve spring, or add a pressure booster.
TROUBLESHOOTING
Inspect hose connector O-rings for damage, replace or
lubricate if needed.
SOLUTION

www.aquorwatersystems.com
[phone]
Aquor®House Hydrant V1+
ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED
29
Hose connector is dicult to connect or disconnect.
We stand behind every product we make. Aquor
oers a 10 year warranty on all stainless steel
components and 5 years on all polymer components.
Our mission is to manufacture the highest quality
water connectors possible, engineered to last
decades of frequent use.
Warranty
PROBLEM
For any questions, please get in touch with our customer
service team at [e-mail] or call
us at [phone] Mon-Fri 9AM-4PM.
Contact Us
Try squeezing your hose nozzle while simultaneously
disconnecting.
If left outdoors in variable weather, water expansion
may have caused the connector’s internal check-valve
to seize. Try disassembling or removing the connector’s
check valve. Test with a dierent hose connector.
There may be a piece of debris stuck in the hydrant’s
main valve. Shut o the water supply, then test the
valve’s forward/back operation with your thumb or a
tool. It should operate smoothly. If needed, remove
hydrant’s operating rod by unscrewing the rear inlet.
If the issue occurs gradually over time, try cleaning the
hydrant’s outlet and lubricating the connector O-rings.
TROUBLESHOOTING, WARRANTY, & CONTACT
SOLUTION
Visit our website to activate
your product warranty.
www.aquorwatersystems.com
/pages/warranty-registration