Aratek Biometrics Technology BM7500 User manual

- 1 -
Fingerprint Smart Terminal
Model No.: BM7500
User’s Manual
V1.3

- 2 -
Thank you for your purchase of the fingerprint smart terminal BM7500 series (hereinafter
referred to as "the device"). Please read the manual carefully to ensure safe and satisfactory
operation, and keep the manual for future reference.
This manual is applicable to following type of products:
BM7500 BM7510 BM7520 BM7530 BM7540 BM7550 BM7560 BM7570 BM7580 BM7590
Content
1. Warm Tips.......................................................................................................................... - 3 -
2. Warning.............................................................................................................................. - 3 -
3. Product Introduction .......................................................................................................... - 3 -
4. The Quick Start Guide ....................................................................................................... - 5 -
5. The Index........................................................................................................................... - 6 -
6. About the Battery............................................................................................................... - 8 -

- 3 -
1. Warm Tips
(1) The manual is subjected to change without prior notice.
(2) The manual is a general guide for the product. Functions might be increased or reduced
due to customized needs. Please contact local distributors for details.
2. Warning
★Unauthorized disassembly is forbidden, or else at your own risk.
★Do not charge with standard higher than original battery and charger.
★Do not dispose of the product in a fire or heat as the product may cause crack and injury.
3. Product Introduction
(1) Product Photos
a). Front and Sides of the Product
b). Back of the Product

- 4 -
c). Carapace of the product
(2) Components
NO.
Name
Function
1
Front camera
2 mega pixels
2
Fingerprint
sensor
To place the fingers on the window capture
the fingerprint
3
Reading area
Put the ID card near the zone
4
Power
On/off
5
Reset
Restart the machine forcefully
6
Microphone
For call or recording
7
UART port
Reserved function
8
Mirco USB
USB data port and charging port
9
TF card port
Available for extension (up to64G)
10
Earphone port
3.5mm
11
2Dbarcode
reader
Available for built-in 2Dbarcode
12
Rear camera
8 mega pixels and automatic focusing
13
Flashlight
LED flashlight
14
Nut for fixing
carapace
Fix carapace with the screw on it
15
Battery cover
locker
Push the locker to open or close the battery
click
16
Bind glove
leather
Installed on carapace, avoid slipping down of
handheld device
17
Screw to
fix carapace
Install carapace on the back of mainframe
with the screw to fix

- 5 -
4. The Quick Start Guide
(1) Charging operation
AC adapter is USB port adapter. Plug the USB connector into adapter’s USB port
while the other side into the device’s Micro-USB port. Plug inAC adapter for
Charging.
(2) On/off operation
When the device is power-off, long press the power key for 5 seconds, and the
device vibration or screen-on indicates start-up. When the device is power-on, short
press the power key to get into standby or wake-up. When the device is power-on
but not standby mode, press the power key for over 2 seconds then pop up interface
of “power off”, “airplane mode”and “silent mode”. Then select “power off”.
(3) Please power off the device before inserting or removing the SIM card, otherwise
the product may be damaged.

- 6 -
5. The Index
Hardware Parameters
Items
Detailed description
CPU
1.3GHz GHz Quad-Core Processor
Display
7.0 Inch Display ，1280×720 pixels
Touch Screen
Capacitive Touch Screen
RAM
1G RAM
SIM card
Standard dual Micro SIM Card
Data
RAM
Onboard
8G ROM
Expandable
Memory
TF Card（up to 64G)
Camera
Front
2 mega pixels
Rear
8mega pixels, automatic focusing
Audio
Decoder
Support 2.1 sound output
Built-in Mic
1
Receiver
Not supported
Speaker
Stereo Speaker
Interface
Headphone port
3.5mm
Micro USB
1
TF Card slot
1
RJ45
Not supported
USB
USB OTG 2.0
UART port
Optional
Button
Power Switch
G-Sensor
Optional
Light- sensor
--
Proximity sensor
--
Gyroscope
Not supported（E-compass available)
GPS
Optional
Motor
Not supported
GSM
GSM 850//1900 MHz，WCDMA 850/1900 MHz
GPRS
GPRS，EDGE，HSPA
Fingerprint
Sensor
Capacitive1/Capacitive2/optical
Active Area
10.64mm×14mm/14.25*19.3 mm /16.26*24.38
mm
Image size
256x288 /256x360/320x480
Resolution
500dpi

- 7 -
Wireless
Wi-Fi
support
Bluetooth4.0
support
3G
support
Power
Battery
Li-polymer6000mAh/10000mAh
AC supply
DC 5V/1.5A USB cable
OS（Operating System）
Android 4.4
Accessories
AC adapter
USB Cable
Machine Weight
780g
Dimension
235mm*147mm*28mm
Extensive Function
Built-in QR decoder (Optional)
Operating Environment
Working temperature ：0℃～70℃
Relative humidity≤90%
Temperature for Storage and
Transportation
-40～60℃
EMC
★ESD meets the third level condition of contact
discharge formulated in table one of GB 17626.2
★RS meets the secondary conditions formulated
in table one of GB 17626.3
RF Section
Specification
(Optional)
★Antenna resonant frequency：13.56MHz
★Antenna energy output：
Antenna surface magnetic field strength（Hmax
≤7.5A/m（rms）
Electromagnetic field intensity at the 3cm of
the antenna surface normal direction（Hmin)
≥1.5A/m（rms）
★Modulation output ：
Bit rate：106Kbit/s（fc/128）
Modulation Mode：ASK Modulation
Modulation index ：8％～14％
Coding method：NRZ-L
★Subcarrier modulation input ：
Subcarrier frequency（fs）：847kHz
Modulation subcarrier mode：BPSK
Valid reader distance:0~3cm

- 8 -
QR code
Image sensor
752*480 CMOS
illumination
Red Light LED 625±10nm
identification
code system
2Dbarcode PDF417, Data Matrix, QR Code；
1Dbarcode UPC/EAN,Code39,Code128,code93；
Recognition
view
Revolve 360*, incline +50*,deflection+50*
Second
generation
ID card
technical
standard
Meet the standard of ISO/IEC 14443 type B, The
General Technique Requirements of GA450-2003
Desktop Resident Identity Card Reader and the
first revision list of The General Technique
Requirements of the 1GA450-2003 Desktop
Resident Identity Card Reader(draft).
Reading time
<3s
Reading
distance
0～3cm
Working rate
13.56MHz±7kHz
6. About the Battery
High-performance 6000mAh Li-polymer battery is installed in the terminal.
(1) Battery Life：
Up to 8 hours for continuous work, standby for a week.
(2) Charging Method：
Please charge your battery on time when the system warns. A full charge to 100% is
necessary.
(3) Time for Charging：
A standard 6000mAh battery charge takes about 8-10 hours.
(4) Operating Notice
a). The standby time is measured in an actual environment, but the specific standby time
may vary in different areas. This is due to various factors.
b). A rechargeable battery for the device can charge and discharge hundreds of times, but it
will eventually wear out. When standby times are noticeably shorter than normal,
replace the original battery.
c). Disconnect the device and unplug charger after use.
d). Enter system hibernation if no intend to use battery for long period. Battery should be
kept in dry environment with full charge. Charge and discharge once every 3 to 6
months.
e). Use designated battery for replacement.

- 9 -
7. Optional Genuine Accessories
(1) USB data cable
(2) AC adapter
(3) Battery
(4) Carapace
8. Simple Troubleshooting Guide
phenomenon
Cause
Operation
Abnormal Charge
Not full insertion of AC
adapter into household
outlet
Check plug insertion
Poor contact of USB port
Ensure good contact of USB port
Heating
Normal phenomenon under
service conditions
Avoid using in a too hot
environment, or stop operation for
a while
Crash
Malware running or BUG
in running software
Press reset button, avoid malware
in peacetime
9. Maintenance & Repair
(1) Keep the device dry in case rain, humidity and all kinds of liquids or moisture containing
minerals will erode electronic wires.
(2) Avoid using and storing the device in dusty and dirty place in case detachable parts and
internal electronic components damaged.
(3) Do not put the device in a too hot place because high temperature shortens the life of
electronic devices, destroys batteries, deforms and melts some plastic components.
(4) Do not store the device in a too cold place. Or else when the temperature of the device
rises (to normal temperature), humidity appears inside it then destroys circuit board.
(5) Open the device in accordance with the manual, do not try other methods.
(6) No throw, beat or vibration allowed, because that will damage the inner circuit board and
its precision architecture.
(7) Do not clean the device with strong chemicals, cleaning agents and strong detergents.
(8) Do not paint the device because paints affect detachable parts work smoothly.
(9) The charger is for indoor use only.
(10) Capacitive touch panel designation, avoid extrusion with hard objects, scratch or rude
touching in case touch panel fracture or failure.

- 10 -
(11) Power off while long time no use.
(12) Abnormal situation may happen due to increasing electromagnetic interference. Please
reboot system after shutdown.
The suggestions above are applicable equally to the product, battery, charger and all
accessories. If abnormal situation of any accessory happens, contact local authorized agent
for replacement or maintenance.
reference number ：BM7500-manual-V1.3
version number:V1.3
issue date: 29-march-2016
Manufacture ：Aratek Biometrics Technology Co.,Ltd.
Model No.：BM7500
Address: 2F, T2-ABuilding, ShenZhen Software Park, South Area, Hi-Tech Park, ShenZhen, Guangdong, China
Website: www.aratek.com.cn

- 11 -
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not
cause harmful interference.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information:
This GSM Mobile Phone meets the government's requirements for exposure to radio waves. The guidelines are
based on standards that were developed by independent scientific organizations through periodic and thorough
evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of
all persons regardless of age or health.
FCC RF Exposure Information and Statement
The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: BM7500 (FCC ID:
2AGUJ-BM7500) has also been tested against this SAR limit. The highest SAR value reported under this standard
during product certification for use when properly worn on the body is 0.620W/kg. This device was tested for typical
body-worn operations with the back of the handset kept 0mm from the body. To maintain compliance with FCC RF
exposure requirements, use accessories that maintain a 1cm separation distance between the user's body and the
back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components
in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF
exposure requirements, and should be avoided.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum
separation distance of 0mmmust be maintained between the user’s body and the handset, including the antenna.
Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic
components. Body-worn accessories that do not meet these requirements may not comply with RF exposure
requirements and should be avoided. Use only the supplied or an approved antenna.