Arbor Technology PBN-9007 User manual

- 1 -
Quick Installation Guide
Version 1.2
PBN-9007
COM Express Mini Type 10 Carrier Board
Form Factor
COM Express
Carrier Board
I/O
SATA, USB, COM, SIM,
Mini-card, CFast
Video
Single Channel LVDS,
Display Port
Ethernet
RJ-45 LAN Connector
Audio
ALC662 CODEC,
Line-out, Mic-in,
If you have any technical difculties, please consult the user’s manual rst at:
http://www.arbor.com.tw
Please do not hesitate to call or e-mail our customer service when you still can not
nd out the answer.
http://www.arbor.com.tw
E-mail: [e-mail]
♦ Technical Support
Copyright® All Rights Reserved. 4040900700120P
FCC Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions : (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

- 2 -
COM Express Module Type Summary Features
COM Express supports seven pin-out Type apply to Basic and Extended form factors:
Module Type 1 and 10 supports single connector with two rows of pins (220 pins)
Module Type 2, 3, 4, 5 and 6 support two connectors with four rows of pins (440 pins)
Connector placement and most mounting holes have transparency between Form
Factors.
The differences amount the Module Types are summarized in table below:
Module Type 1 10 2 345 6
Connectors 1 1 2 2 2 2 2
Connector Rows A, B A, B A, B,
C, D
A, B,
C, D
A, B,
C, D
A, B,
C, D
A, B,
C, D
PCIe Lanes (max) 6 4 22 22 32 32 24
PCI Bus No No Yes Ye s No No No
PATA - IDE No No Yes No Ye s No No
LAN (Max) 1113131
Serial Ports No 0 / 2 No No No No 0 / 2
Muxed SDVO No No 0 / 2 0 / 2 0 / 2 0 / 2 No
Digital Display I/F No No No No No No 0 / 3
USB 3.0 Ports No No No No No No 0 / 4
DDIs No No No No No No 0 / 3
LVDS Channel A 0 / 1 0 / 1 0 / 1 0 / 1 0 / 1 0 / 1 0 / 1
LVDS Channel B 0 / 1 No 0 / 1 0 / 1 0 / 1 0 / 1 0 / 1

- 3 -
Packing List
Before you begin installing your single board, please make sure that the following
materials have been shipped:
1 x PBN-9007 COM Express Mini Type 10 Carrier board
1 x Quick Installation Guide
Ordering Information
PBN-9007 COM Express Mini Type 10 Carrier Board
Cable Kit CBK-05-9007-00
Specications
Form Factor COM Express Mini Type 10 Carrier Board
I/O Chips Fintek F71869
Audio ALC662 CODEC, Line-out, Mic-in with Phone Jack
Storage 1 x Serial ATA connector, 1 x CFast socket
Serial Port
COM1: RS-232
COM2: RS-232/422/485 selectable
TX/RX COM Port (depending on CPU Module)
USB 2.0 4 x USB 2.0 ports
USB 3.0 2 x USB 2.0/3.0 ports
LCD Single Channel LVDS connector
Display Port DisplayPort connector
DIO 8-bit Digital Input/Output
Expansion Interface 1 x Mini-card full size socket
Operation Temp. -40ºC~85ºC (-40ºF~185ºF)
Power Connector +12V DC main functioning, Power Jack
Dimension (L x W) 95 x 125 mm (3.7” x 4.9”)

- 4 -
Board dimensions
23.9
53
85
12
27 11
54
81.66 18.86
Unit:mm
Ø 3.1* Ø6.4
16.8
10.28
8
1.6
125

- 5 -
4
66
121
4
53.28
91
4.15
95
125
Unit:mm

- 6 -
Jumpers/ Connectors Quick Reference
Jumpers
Label Description
JRS1 COM 2 RS-232/422/485 Serial Port Selection
JP1 AT / ATX, BIOS From CPU Module / Carrier Board Selection
JBAT1 Clear CMOS Setting
JLCD2 LCD Mode S election
JINV1 Inverter Voltage Setting
JBL1 LVDS Brightness Control Mode Selection
JLCD1 LCD Voltage Setting
JTOP1 CPU Board Power Source Selection

- 7 -
Connectors
Label Function
COM2 RS-232/422/485 Serial Port Connector
DIO1 Digital I/O Connector
JFRT1 Front-panel switches and LED Indicators Connector
USB2 USB Connector
USB3 USB Connector
SATA1 Serial ATA Connector
PWR1 SATA Power Connector
LAN1, LAN2 Ethernet Connectors
USB1 Double Stack USB 2.0/3.0 Connector
MIC1 Microphone
LINE_OUT1 Line-out
PW1 Power Button
5W_T1 Touch Screen Connector
LVDS1 LVDS Connector
INV1 LCD Inverter Connector
PADP1 DC Power Connector
CON1 CPU Board COM Port
DP1 DisplayPort Connector
COM1 RS-232 Serial Port
CPUF1 Fan Power Connector
KBMS1 KB/MS Connector
MC1 Mini-Card Socket
CF1 CFast Socket
SIM1 SIM Card Socket

- 8 -
Jumpers
JSR1
1
JBL1
JLCD1 7
JTOP1 8
6
JLCD2
JINV1
5
4
JP1
JBAT1
3
2

- 9 -
Connectors
USB2
PWR1
USB3
910
11 12
15
13
SATA1
14
COM2 DIO1
JFRI1
LAN2
LAN1
USB1
MIC1
Line_OUT1
PW1
16
17
18
19
20
21
23
LVDS1
INV1
24 22 5W_T1
25
27
28
29
30
PADP1
26
CON1
COM1
DP1
CPUF1
KBMS1
CF1
32
SIM1
33
MC1
31

- 10 -
Jumpers
JRS1: COM2 RS-232/422/485
Serial Port Selection(1)
Connector type: 2.00mm pitch 2x3-pin
headers.
Mode RS-232
(Default) RS-422 RS-485
1-2 Short Open Open
3-4 Open Short Open
5-6 Open Open Short
6
5
21
6
5
21
6
5
21
JP1: AT/ATX Mode Selection (2)
Connector type: 2.00mm pitch 1x2-pin header.
Pin Description
1-2 ON AT Mode
3
1
4
2
3
1
4
2
3
1
4
2
3
1
4
2
1-2 OFF ATX Mode
3
1
4
2
3
1
4
2
3
1
4
2
3
1
4
2
JP1: BIOS from CPU Board / Carrier
Board Selection (2)
Connector type: 2.00mm pitch 1x2-pin header.
Pin Description
3-4 ON CPU
3
1
4
2
3
1
4
2
3
1
4
2
3
1
4
2
3-4 OFF Carrier
3
1
4
2
3
1
4
2
3
1
4
2
3
1
4
2
JBAT1: Clear CMOS Setting (3)
Connector type: 2.00mm pitch 1×3-pin header.
Pin Mode
1-2 keep CMOS (default)
23 1
2-3 clear CMOS
23 1
JLCD2: LVDS Panel Mode
Selection (4)
Connector type: 2.00mm pitch 2×2-pin
headers.
Pin LCD Mode
1-3 Scan
Direction 0V:ON, High:Off
3
1
4
2
2-4 Frame Rate 0V:ON, High:Off
3
1
4
2
JINV1: LCD Inverter Voltage
Selection (5)
The voltage of inverter could be selected by
JINV1 in +5V or +12V.
Connector type: 2.00mm pitch 1×3-pin header.
Pin Voltage
1-2 +5V
23 1
2-3 +12V (default)
23 1
JBL1: LVDS1 Brightness Control
Level and Mode Selection (6)
Connector type: 2.00mm pitch 2×3-pin
headers.
Pin Brightness Control Source
1-3 5V PWM mode control
(default)
65
2
1
65
2
1
65
2
1
65
2
1
3-5 3.3V PWM mode control
65
2
1
65
2
1
65
2
1
65
2
1
2-4 5V DC level control
65
2
1
65
2
1
65
2
1
65
2
1
4-6 0V DC level control
65
2
1
65
2
1
65
2
1
65
2
1

- 11 -
JLCD1: LVDS Panel Voltage
Selection (7)
The voltage of LVDS panel could be selected
by JVLCD1 in +5V or +3.3V.
Connector type: 2.00mm pitch 1×3-pin header.
Pin Voltage
1-2 +5V
23 1
2-3 +3.3V (default)
23 1
JTOP1: CPU Board Power Source
Selection (8)
Connector type: 2.00mm pitch 2×5-pin
headers.
Pin LCD
1-2
3-4 12V (default)
1 2
109
5-6
7-8
9-10
5V
1 2
109
Connectors
COM2: RS-232/422/485
Serial Port (9)
Connector type: 2.00mm pitch 2×7-Pin
lockable box headers.
Pin Desc. Pin Desc.
12
13
14
2DCD2 1RXD2
4TXD2 3DTR2
6GND 5DSR2
8RTS2 7CTR2
10 RI2 9NC
12 422TX+ /485+ 11 422TX- /485-
14 422RX+ 13 422RX-
DIO1: Digital I/O Connector (10)
DIO1 is a 8-bit GPIO connector.
Connector type: 2.00mm pitch 2×5-pin
lockable box headers.
Pin Desc. Pin Desc.
12
9
10
2DIO0 1DIO1
4DIO2 3 DIO3
6 DIO4 5 DIO5
8 DIO6 7DIO7
10 +5V 9GND
JFRT1: Front-panel switches and
LED Indicators Connector (11)
Connector type: 2.00mm pitch 2×5-pin
headers.
Pin Desc. Pin Desc.
12
10
9
1 RESET+ 2 RESET-
3 Power
LED+
4Power
LED-
5 HD LED+ 6 HD LED-
7Speak+ 8 Speak-
9 POSN+ 10 POSN-

- 12 -
LAN1, 2: Ethernet Connectors
(16, 17)
Connector type: RJ-45 connectors
The pin assignments conform to the industry
standard.
USB1: Double Stack USB 2.0/3.0
Connector (18)
Connector type: double stack USB 2.0/3.0
type A connector.
The pin assignments conform to the industry
standard.
MIC1: Microphone (19)
Connector type: Audio jack (Pink)
LINE_OUT1: Line-out (20)
Connector type: Phone jack (Green)
PW1: Power Button (21)
USB2: USB Connector (12)
Connector type: 2.00mm pitch 2x5-pin
lockable box headers.
Pin Desc. Pin Desc.
12
9
10
2+5V 1+5V
4USB- 3 USB-
6 USB+ 5 USB+
8 GND 7GND
10 GND 9GND
USB3: USB Connector (13)
Connector type: 2.00mm pitch 2x5-pin pin
headers.
Pin Desc. Pin Desc.
12
10
9
1+5V 2+5V
3 USB- 4USB-
5 USB+ 6 USB+
7GND 8 GND
9GND 10 GND
SATA1: Serial ATA Connector (14)
Support high speed transfer rates and SATA
RAID function.
Connector type: Standard 7-pin SATA
connector.
Pin Description
1
7
1GND
2 TX+
3TX-
4GND
5RX-
6RX+
7GND
PWR1: SATA Power Connector
(15)
Connector type: 1x4-pin wafer connector
Pin Description
1
4
15V
2GND
3 GND
4 12V

- 13 -
5W_T1: Touch Screen Connector
(22)
Connector type: 2.54mm pitch, 1×5-pin wafer
connector.
Pin Description 1
2
3
4
5
1 UL
2 UR
3 PROBE
4 LR
5LL
LVDS1: LVDS Connector (23)
Connector type: 1.25mm FI-SE20P-HFE
Pin Desc. Pin Desc.
1
20
1 TX3+ 2TX3-
3SCAN DIRECTION 4FRAME RATE
5GND 6CLK+
7CLK- 8GND
9TX2+ 10 TX2-
11 GND 12 TX1+
13 TX1 14 GND
15 TX0+ 16 TX0-
17 GND 18 GND
19 VDD 20 VDD
INV1: LCD Inverter Connector (24)
Connector type: 2.0mm pitch, 1×5-pin wafer
connector.
Pin Description
1
2
3
4
5
1 +12V
2GND
3 Backlight on/off
4Brightness control
5 GND
PADP1: DC Power Connectors (25)
Connector type: DC power jack connector.
Pin Description
GND
DC_IN
1DC_IN
2GND
3 GND
CON1: CPU Board COM Port (26)
Connector type: 2.0mm pitch, 2x5-pin headers
Pin Desc. Pin Desc.
12
10
9
13.3V 23.3V
3NC 4 NC
5RX0 6RX1
7GND 8 GND
9 TX0 10 TX1
DP1: DisplayPort Connector (27)
Connector type: DisplayPort digital video
connector
The pin assignments conform to the industry
standard.
1
19
2
20
COM1: RS-232 Serial Port (28)
Connector type: DB9 male connector
JCOM3
JCOM2
JCOM1
1 5
69
Pin Desc. Pin Desc.
1DCD1 2RXD1
3 TXD1 4DTR1
5 GND 6 DSR1
7 RTS1 8CTS1
9 RI1 10 NC

- 14 -
CPUF1: Fan Power Connector (29)
Connector type: 12V 2.54mm 1x3-pin wafer
connector.
Pin Description
1
2
3
1GND
2 +12V
3 Fan_Detect
KBMS1: KB/MS Connector(30)
Connector type: 2.00mm pitch 1x6-pin wafer
connector.
Pin Description
1
2
3
4
5
6
1KB_DAT
2GND
3 MS_DAT
4KB_CLK
5PS2_VCC
6 MS_CLK
MC1: Mini-card Socket (31)
Connector type: Onboard 0.8mm-pitch 52-pin
edge card connector
The pin assignments conform to the industry
standard.
52
51
16
18
15
17
2
1
Mini-Card
Socket
CF1: CFast Socket (32)
(On Bottom Side)
Connector type: CFast connector
The pin assignments conform to the industry
standard.
PC1
S7
S1
PC17
PC1
S7
S1
PC17
SIM1: SIM Card Socket (33)
(On Bottom Side)
Connector type: Foxconn WL618E2-U05-7F
CX1 socket
Pin Description
C3
C7
C6
C2
C5
C1
C1 VCC
C2 RST
C3 CLK
C5 GND
C6 VPP
C7 IO