Arbor Technology Gladius G0710S User manual

Gladius G0710(S)
Rugged Tablet PC
User's Manual
Version 1.0
2009.12P/N: 4012071000100P

This page is intentionally left blank.

- I -
Index
Contents
Copyright Notice...............................................................i
Declaration of Conformity................................................i
Important Safety Instructions.........................................ii
Classication...................................................................iii
Disposing of Your Old Product......................................iv
Symbols Description......................................................iv
About User's Manual .......................................................v
Warning.............................................................................v
Additional Information & Technical Support.................v
Contact Information.........................................................v
Warranty...........................................................................vi
Chapter 1 - General Information.........................................1
1.1 Packing List................................................................2
1.2 Ordering Information.................................................2
1.3 Specications.............................................................3
1.4 Dimensions.................................................................5
1.5 Introduction................................................................6
1.5.1 Front Side........................................................7
1.5.2 Function Buttons............................................8
1.5.3 LED Indicators................................................8
1.5.4 Rear Side.........................................................9
1.5.5 Right Side......................................................10
1.5.6 Left Side........................................................10
Chapter 2 - Using the Tablet PC.......................................11
2.1 Getting Started.........................................................12
2.2 Battery Replacement...............................................13
2.3 SIM Card Installation ...............................................16
2.4 DC Power Supply.....................................................17
2.5 Drivers & Utilities Installation.................................18
2.5.1 Touch Screen Driver Installation ................18
2.5.2 Chipset Driver Installation...........................21
2.5.3 Graphics Driver Installation ........................24

- II -
Index
2.5.4 Audio Driver Installation..............................27
2.5.5 LAN Driver Installation.................................29
2.5.6 Wireless LAN Driver Installation.................31
2.5.7 Bluetooth Driver Installation.......................32
2.5.8 RFID Driver Installation................................36
2.5.9 Function Key Tray Installation....................39
2.6 Touch Screen ...........................................................41
2.6.1 Tips for Using the Stylus.............................41
2.6.2 PenMount Monitor........................................42
2.6.3 PenMount Control Panel..............................43
2.7 Function Key Tray....................................................50
2.7.1 Function Key Conguration ........................50
Chapter 3 - BIOS................................................................51
3.1 BIOS Main Setup.....................................................52
3.2 Advanced Settings..................................................53
3.2.1 IDE Conguration ...............................................54
3.2.2 Brightness Default Level....................................57
3.2.3 Install OS Conguration.....................................57
3.2.4 Bluetooth Conguration ....................................57
3.2.5 RFID Conguration.............................................57
3.2.6 WiFi Conguration..............................................57
3.2.7 Battery Low Beep Conguration.......................57
3.3 Boot Settings...........................................................58
3.3.1 Boot Settings Conguration..............................59
3.3.2 Boot Device Priority ...........................................60
3.3 Security....................................................................61
3.4 Exit Options.............................................................63
Appendix............................................................................65
A.1 POGO Connector....................................................66

- i -
Copyright Notice
All Rights Reserved.
The information in this document is subject to change without prior notice in
order to improve the reliability, design and function. It does not represent a
commitment on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct, indirect,
special, incidental, or consequential damages arising from the use or inability
to use the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright.
All rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of the manufacturer.
Declaration of Conformity
CE Class B
This product has passed the CE test for environmental specications when
shielded cables are used for external wiring. We recommend the use of
shielded cables. This kind of cable is available from ARBOR. Please contact
your local supplier for ordering information.
This product has passed the CE test for environmental specications. Test
conditions for passing included the equipment being operated within an
industrial enclosure. In order to protect the product from being damaged by
ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the
use of CE-compliant industrial enclosure products.
FCC Class B
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a residential environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.

- ii -
IEC 60601-1/EN60601-1
This product complies with the system standard IEC 60601-1 Medical Electri-
cal Equipment Part 1: General Requirements for Safety. And therefore, the
product is exclusively interconnected with IEC 60601-1 certied equipment in
the patient environment.
Equipmentconnectedtotheanalogordigitalinterfacesoftheunitmustcomply
with the respective IEC standards (e.g. IEC 60601-1 for medical equipment).
Furthermore all congurations shall comply with the current version of the
standard for SYSTEMS IEC 60601-1-1. Everybody who connects additional
equipment to the signal input part or signal output part congures a medical
system, and is therefore responsible that the system complies with current
version of the requirements of the system standard IEC 60601-1-1. If in doubt,
consult the technical service department or your local representative.
Important Safety Instructions
Read these safety instructions carefully
1. Read all cautions and warnings on the equipment.
2. Place this equipment on a reliable surface when installing. Dropping it or
letting it fall may cause damage
3. Make sure the correct voltage is connected to the equipment.
4. For pluggable equipment, the socket outlet should be near the equipment
and should be easily accessible.
5. Keep this equipment away from humidity.
6.DisconnectthisequipmentfromtheA/Coutletbeforecleaningit.Useamoist
cloth. Do not use liquid or sprayed detergent for cleaning.
7. Do not scratch or rub the screen with a hard object.
8. Never use any of the solvents, such as Thinner Spray-type cleaner, Wax,
Benzene,Abrasive cleaner,Acid orAlkaline solvent, on the Medical Display.
Harsh chemicals may cause damage to the cabinet and the touch sensor.
9. Remove dirt with a lightly mositened cloth and a mild solvent detergent.
Then wipe the cabinet with a soft dry cloth.
7. The openingsontheenclosureareforairconvection andprotectthe equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Position the power cord so that people cannot step on it. Do not place
anything over the power cord.
9.Ifthe equipment will not be used for a long time, disconnectitfromthepower
source to avoid damage by transient overvoltage.

- iii -
10. Never pour any liquid into openings. This may cause re or electrical
shock.
11. Never open the equipment. For safety reasons, the equipment should be
opened only by qualied service personnel.
12. If one of the following situations arises, get the equipment checked by
service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according
to the user's manual.
e. The equipment has been dropped or damaged.
f. The equipment has obvious signs of breakage.
13. The sound pressure level at the operator's position, according to
IEC 704-1:1982, is no more than 70dB(A).
14. Keep this User’s Manual for later reference.
15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW
-20° C (-4° F) OR ABOVE 60° C (140° F). THIS MAY DAMAGE THE
EQUIPMENT.
UL Class I Classcation: With respect to electric shock, re and
mechanical hazards only, in accordance with UL-60601-1 and
CAN/CSA C22.2 No. 601.1.
Classication
Powered by Class I power supply
No applied part
Degree of protection against the ingress of water: IPX0
Mode of operation: Continuous
The equipment is not suitable for use in the presence of a ammable
anesthetic mixture with air or nitrous oxide: Not AP or APG Category.
•
•
•
•
•

- iv -
Disposing of Your Old Product
Within the European Union
EU-wide legislation, as implemented in each Member State,
requires that waste electrical and electronic products carrying the
mark (left) must be disposed of separately from normal household
waste.
This includes monitors and electrical accessories, such as signal cables or
power cords. When you need to dispose of your display products, please
follow the guidance of your local authority, or ask the shop where you
purchased the product, or if applicable, follow any agreements made between
yourself. The mark on electrical and electronic products only applies to the
current European Union Member States.
Outside the European Union
If you wish to dispose of used electrical and electronic products outside the
European Union, please contact your local authority so as to comply with the
correct disposal method.
•
•
Symbols Description
This symbol indicates that there is a danger of injury to the
user or a risk of damage to the product, should warning
notices be disregarded.
Direct Current
Ground
Stand-by

- v -
About User's Manual
This User's Manual is intended for experienced users and integrators with
hardware knowledge of personal computers. If you are not sure about any
description in this User’s Manual, please consult your vendor before further
handling.
Warning
Any changes or modications not expressly approved by the guarantee of this
device could void the user’s authority to operate the equipment.
Additional Information & Technical Support
You can download the related technical documents such as datasheet and
user’s manual as well as driver on our website.
Please do not hesitate to call or e-mail our customer service when you still
cannot get the information you need.
http://www.arbor.com.tw
E-mail: [e-mail]
Contact Information
ARBOR Technology Corp.
10th ., No. 700, Zhong Zheng Rd., Zhong He, 235 Taipei, Taiwan.
TEL: [phone]
FAX: [phone]

- vi -
Warranty
This product is warranted to be in good working order for a period of one year
from the date of purchase. Should this product fail to be in good working order
at any time during this period, we will, at our option, replace or repair it at no
additional charge except as set forth in the following terms. This warranty
does not apply to products damaged by misuse, modications, accident or
disaster. Please be advised that disassembling this equipment may void the
warranty as well.
Vendor assumes no liability for any damages, lost prots, lost savings or any
other incidental or consequential damage resulting from the use, misuse of,
or inability to use this product. Vendor will not be liable for any claim made by
any other related party.
Vendordisclaimsallotherwarranties,eitherexpressedorimplied,includingbut
not limited to implied warranties of merchantibility and tness for a particular
purpose, with respect to the hardware, the accompanying product’s manual(s)
and written materials, and any accompanying hardware. This limited warranty
gives you specic legal rights.
Return authorization must be obtained from the vendor before returned
merchandise will be accepted. Authorization can be obtained by calling or
faxing the vendor and requesting a Return Merchandise Authorization (RMA)
number. Returned goods should always be accompanied by a clear problem
description.