Arbor Technology Gladius 5 User manual

5.5” Rugged IoT Handheld
Device with Quad-core Processor
User Manual
使用手冊
PN:4000055002100P

Version 1.0
Copyright Notice
All Rights Reserved.
This document contains proprietary information protected by copyright. All rights
are reserved. No part of this manual may be reproduced by any mechanical,
electronic, or other means in any form without prior written permission of the
manufacturer.
Disclaimer
The information in this document is subject to change without prior notice in order
to improve the reliability, design and function. It does not represent a commitment
on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct, indirect,
special, incidental, or consequential damages arising from the use or inability
to use the product or documentation, even if advised of the possibility of such
damages.

III
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modications not expressly approved by the
part responsible for compliance could void the user’s authority to operate the
equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.Operation is subject to the
following two conditions:
1) this device may not cause harmful interference and
2) this device must accept any interference received, including interference that
may cause undesired operation of the device.
FCC RF Radiation Exposure Statement:
For body worn operation, this phone has been tested and meets FCC RF
exposure guidelines when used with an accessory that contains no metal and
that positions the handset a minimum of 1.5 cm from the body. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines.

IV
NCC警語：
根據NCC低功率電波輻射性電機管理辦法 規定: 第十二條 經型式認
證合格之低功率射頻電機，非經許可，公司、商號或使用者均 不得擅
自變更頻率、加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；
經發現有干 擾現象時，應立即停用，並改善至無干擾時方得繼續使
用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射
頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機 設備之
干擾。
「減少電磁波影響，請妥適使用」。
「SAR標準值2.0W/Kg；SAR實測值為：0.222W/Kg」。
「EMC品質符合CNS13438限制值，充電線組限用原廠含鐵粉芯、1米長之
隔離線USB Cable」。

1
Open Your Box
Rugged IoT Handheld Device
Rechargeable Li-ion battery pack (Pre-installed)
Standard USB cable
Universal power adapter
Earphone
User Manual
1Front camera 10 Power key
2Receiver * Press-and-hold this key to power on/off the computer.
3Scan key * Press this key to turn on/off the display.
4Volume rocker 11 USB connector with rubber cover
5Touch screen 12 Scan window
6(OS) Menu button 13 Headset jack with rubber cover
7(OS) Home button 14 LED Flash
8Microphone 15 Rear camera
9(OS) Back button 16 Battery chamber
17 Speaker
12
3
43
5
10
6 7 8 9
1514 16
10
3
12 13
11
17

2
Battery cover retaining screw
Step 1: Orientate the SIM cards and
microSD card as the symbol directs.
Step 2: Insert the SIM cards and microSD
Card into the slots.
Battery Chamber
Double-stacked SIM card slots
Battery contact pins
microSD card slot
This symbol
indicates the
location of the
microSD card slot.
This symbol
indicates the
location of the
Dual-SIM slots.
Step 3: Restore the battery cover.
Caution: Remove the battery before SIM/microSD
card installation to prevent from damage.
Install SIM & microSD Cards
To remove battery cover:
Step 1:
Loosen the retaining screw
on the battery cover with
a coin.
Step 2:
Detach and remove the
battery cover.
Step 3:
After the battery cover is removed, the
microSD card slot and Dual-SIM slots are located inside the battery chamber.
The Dual-SIM slots, microSD card slot, and battery are
all located inside the battery chamber. To access
these components, remove the battery cover.
Manually undo the retaining screw to gain access
to the battery chamber.

3
Step 2:
Connect the
power adapter
to the USB
cable.
Charging & Data Connection
Data
Connection
Step 3:
Plug the power
adapter to a
power
outlet.
Step 2:
Plug the USB
connector to a USB
port on another
computer.
Step 1:
Plug the USB
cable to the
device.
Charging
Install Main Battery
Battery contact pins
Battery Contact Pins:After the battery
cover is removed, locate the battery
contact pins inside the battery
chamber.
Step 1:
Locate the battery contact pins on the
battery.
Step 2:
Align the battery pins with
the contact pins.
Step 3:
Put the battery inside the
battery chamber.
Step 4: Restore the battery cover.
Battery contact pins
on the battery
Battery
contact
pins
Battery t snugly
inside the battery
chamber

4
認識您的裝置
強固式物聯網手持裝置
抽換式鋰電池
標準USB傳輸/充電線
充電器
耳機
使用手冊
1前置相機 10 電源紐
2聽筒 * 長按關閉/開啟裝置
3條碼掃描鍵 * 按一下關閉/開啟螢幕
4音量鍵 11 USB插孔(含保護蓋）
5觸控螢幕 12 條碼掃描器
6(系統) 功能鍵 13 耳機插孔(含保護蓋）
7(系統) 主螢幕鍵 14 LED 閃光燈
8話筒 15 後置相機
9(系統)返回鍵 16 電池被蓋
17 揚聲器
12 13
11
17
12
3
43
5
10
6 7 8 9
15
14 16
10
3

5
電池蓋螺絲
步驟 1: 依照所指示方向將SIM/microSD卡
對準插槽。
步驟 2:將SIM/microSD卡插入
步驟 3: 裝上電池以及背蓋
電池背蓋開啟方式
雙SIM卡槽
電池槽端子
microSD卡槽
microSD位置
指示圖
SIM卡位置指示圖
注意：先取下電池，再插拔SIM卡以及
microSD卡以免損傷機器或卡。
安裝SIM卡及microSD記憶卡
開啟電池背蓋後，即可見雙sim卡槽，microSD卡槽
與電池都在其中。
要使用這些插槽，必須要開啟電池蓋。
移除電池蓋：
步驟1 用硬幣來旋鬆螺絲
步驟2 移除電池蓋
步驟3 取下電池蓋後即
可使用SIM卡槽和microSD
卡槽

6
步驟 2:
將USB線較大的
一端與充電器
連接
安裝電池
電池槽端子
電池安裝步驟如下:
步驟 1:
將電池對準電池槽端子
步驟 2:
將電池妥善置入
步驟 3:
蓋上電池蓋並鎖緊螺絲
充電及資料傳輸
資料傳輸
步驟 3:
插入電源插座
步驟 1:
將USB線插入裝置
的USB插孔
充電
步驟 2:
將USB線插入您電腦的
USB插槽
電池端子
電
池槽
端子
確認電池置入後
與電池槽密合