arcelik WMA 6506 D User manual

WMA 6506 D
WMA 6508 J
WMA 6510 J
FULL AUTOMATIC
WASHING MACHINE

Part 3:
Determining location and installation
Part 4:
Program selection and washing operations.
Part 1:
Steps before operating Fullautomatic
Washing Machine and safety precautions.
Part 6:
Helpful tips on stain removal
Part 2:
Technical features.
Part 5:
Care and Maintanence.
Part 7:
Before calling service.
Dear Customer,
We wish that this product, manufactured at modern facilities with total quality notions, will
deliver you the best performance. In order to guarantee this, please read this instruction
manual thoroughly and keep it for your future reference.
CONTENTS
www.arcelik.com.tr

The current requirement in order for safe operation of this machine is 16 Ampheres. You will need to have a certified
electrician to connect a 16 Amp fuse, if there is not enough current load.
Your washing machine is set to 230 Volts.
Do not forget to check the grounding in all cases of use with or without the transformer. Our company will not be
responsible for any damages caused by operations without grounding.
In order to bring the machine to ready before use, please call your service technician or a certified plummer.
Your washing machine’s front door is designed reversible. To change the front door’s opening direction please call your
service.
Please perform the first wash with detergent and do not place clothing inside your washing machine. This will ensure that
any left over dirt from production will be cleared from inside of your machine.
The performance of the washing machine depends on the effectiveness of the cleaning agent. Stains can be permanent
if low quality detergents are used. Please take necessary effort to clean the stained clothes as described in following
pages before washing them in the machine.
1
Make sure the on/off switch is in the off position and always allow one to two minutes
for the door safety lock to release the lock. Pull the handle to open the door.
Steps before operating Fullautomatic
Washing Machine and safety precautions
Part 1:
To open the front door
Due to the quality control processes during production, there may be some
water left over in your machine. This does not cause any damage to your
product.

2
Kick plate
Kick plate opening
screw
Capacity (dry fabric)
Height
Width
Depth
Net weight
Power requirement
Nominal current
Total power
Washing speed
Spin speed (WMA 6506 D)
Spin speed (WMA 6508 J)
Spin speed (WMA 6510 J)
5 kg. (11.1 lbs)
85 cm.
60 cm.
54 cm.
60 kg.
230 V, 50 Hz.
10 A.
2350 Watts.
52 rpm.
600 rpm. (max.)
800 rpm. (max.)
1000 rpm. (max.)
Technical features
Part 2:
The appearance and specifications are subject to
change without notice to raise the unit quality.
The graphics shown in the manual are schematic
and it is possible that they not conform with your
washing machine.
Front door
Top lid
On/Off button
Auxiliary function buttons
Thermostat adjustment knob
Program selection knob
Detergent dispenser
Handle

3
1. Removing transport safety bolts at the rear of the machine
Determining location and installation
“C”, should be turned in a
anti clockwise direction
until the bolt can be
partially withdrawn.
Part 3:
Attention!
Please keep the safety bolts for future transportationand reinstate them before transporting your machine.
Never transport your machine without the transport bolts in position.
Never place your machine on a carpet. This prevents air circulation. The electrical components of the
machine may overheat and may cause damage.
P
C
CC
Remove transport safety bolts
and rubber bushes by pulling
outwards. (A up/down action
and a small squirt of washing up
liquid should ease removal.)
The transport safety bolts must
be removed before any operation
of the machine. Bolt heads,
marked “C”.
C
C
Plastic plugs, supplied
inside the protective bag
and designated as “P”,
should be placed in the
safety bolt holes according
to the direction shown.

4
In order for quiet and stable operation, the machine should be placed properly and leveled on its feet.
Your machine comes with two adjustable feet. If the machine is unstable, loosen the plastic counternut
and screw or unscrew the adjustable foot until the machine is leveled perfectly. After positioning,
tighten the counternut for stability.
Water supply
For proper operation, the pressure of water should be between 1 and 10 atm. (1 atm corresponds to
more than 8 liters per minute flow rate at fully open tap.)
To prevent water leaks sealing washers are supplied with the water inlet hose inside the machine,
place these on each of the hose ends and tighten both ends fully.
In order to prevent any water leak damages, keep the water taps closed when not in use. Connect
the cornered end of the hose to the machine water inlet.
2. Feet adjustment
a) Water inlet hose
3. Water connections
Connect the cold water using the hose with blue printing and connect
the hot water using the hose with red printing.

5
b) Water drain hose
Water drain hose could be placed either at the side of the bath tub, or
directly to the drain. The hose should not be bent. Water drain hose should
be secured with the elbow so that it would not fall down on the ground.
4. Electrical connection
Connect the power cord to the appropirate electrical
system which is being supported by the maximum
voltage and current rating indicated on the rating
plate placed inside the kick plate.
Look! Page 1, Steps before operating Fullautomatic
Washing Machine and safety precautions.
Make sure that you have
grounded power outlet.
0 10 20 30 40 50 60 70 80
90 100 11
Water drain hose
could be placed
directly to the drain
water inlet.
The hose should be placed between 40 and
100 cm. from the ground.
Attention! Before any operation of the machine check the following.
Did you close the front door?
Is the tap open? Is water drain hose placed properly? Is power connected?

6
On/off
switch
Quick
wash
Led indicator
Rinse
hold Temperature
adjustment
knob
Program
selection knob
WMA 6510 J
WMA 6508 J
On/off switch
Quick wash
Led indicator
Rinse hold
Spin speed selection
Temperature
adjustment
knob
Program
selection knob
On/off switch
Led indicator
Detergent drawer
WMA 6506 D
Spin speed selection
Detergent drawer
Control Panel

Choose the appropirate detergent specifically used at the full automatic washing machines. Suggested amount is given on the
detergent cover.
Do not attempt to use detergents and bleaching elements that contain chlor and sulphur. The amount of the detergent depends
on the dirt level of fabric, the amount of fabric and the softness of the water.
7
Sort the laundry according to the following groups and wash them seperately:
- white and resistant colored fabrics,
- colored fabrics,
- delicate fabrics (silk, rayon etc.),
- wool.
Be sure to empty pockets and remove any belts, buttons, pins, etc. from the clothing. You can place little clothing materials
(baby socks, etc) inside of pillow cases to avoid them slip into the pump and filter. For stained fabrics, refer to the “Practical
information” section of the operating manual.
Sorting laundry
Detergent and softener selection
Loading the machine
Place the fabrics uniformly inside the machine. Hand knits should be placed inside out in the machine. Make sure that there
is no clothing at the side of the door. Close the door by pushing lightly. If the door does not close completely, the machine
could not be started-a safety measure. Front door is locked untill the end of the washing program and it will not be opened
about 2 minutes following the end of the program.
Preparation

8
Program selection DELICATES
N: Delicate program is used for washing delicate cloths like curtain
or silk fabrics. This program is without prewash and exists of
main wash, 3 rinses and delicate spin. Rinse Hold button can be
selected during the washing program if desired.
WOOLLENS
J: With program selection, which is without pre-wash, wool fabrics
are washed throughly. Main wash, 3 rinses, woollen spin. Rinse
hold button can be selected during the washing program if desired.
K: Delicate spin program. If rinse hold button is not selected during
J program, 600 rpm delicate spin is applied after the wash cycle.
K delicate spin program will be applied if delicate program (N) is
choosen. Similarly woollen spin will be applied if woollen program
(J) is selected.If additional delicate spin is desired, the program
selection knob should be brought to K.
P: If Rinse hold button is selected during the wash programs F,
N, J and spin is not desired, water in the machine can be
discharged by bringing the program selection knob to P.
Rinse
Fabric conditioner
SYNTHETICS
F, H Programs
These programs are designed for synthetic fabrics, naylon clothing,
curtains and iron free wool fabrics. Clothing are washed with more
water delicately.
F: Program with main wash (main wash, 3 rinses; delicate spin)
H: Delicate spin program is applied automatically at the end of F
washing program if the Rinse hold button is not selected. If
additional delicate spin is desired, the program selection knob
should be brought to H.
COTTONS
A, B, C Programs
These programs are used for white and color cotton fabrics.
A: Program with pre-wash (pre-wash, main wash, 3 rinses, spin)
B: Program with main wash (main wash, 3 rinses spin)
C: Spin
Spin program is applied automatically in A and B programs. Should
an extra spin is desired, program selection knob should be brought
to C.
Warning! Before turning the program selection knob you should first turn off the machine, then make your selection,
and then turn on the machine by pushing the on/off button. Before any washing operation, make sure the power
cord is plugged and the tap is on. Also be sure that the discharge hose is placed properly and the front door is
closed.

9
Fill the fabric softener to the marking. Any
excess amount of softener will mix into
the wash water and you will have to re-fill
the compartment. Hardened softener may
clogg the siphon, in this case add some
water to the softener.
a. Compartment I. detergent compartment
for prewash cycle.
b. Compartment II. detergent
compartment for wash cycle.
c. " " Compartment for fabric
conditioner.
d. Siphon.
Detergent dispenser
Spin speed selection switch (only for WMA 6510 J)
When you want to reduce the spin speed to 500 rpm, press this button.
Spin speed selection switch (only for WMA 6508 J)
When you want to reduce the spin speed to 500 rpm, press this button.
800
500
Rinse hold
If you desire to leave your synthetic and wool fabrics in the machine after the wash
program you may select the Rinse hold button to prevent them getting wrinkled. To
continue the program, you can either press the Rinse hold button again or select
P on the program selection knob to discharge the water.
Quick wash
Shortens washing time for lightly soiled fabrics. This function can be used for cotton
and synthetic programs for temperatures below 60ºC.
1000
500

10
Program selection table
Program selection and machine operation
Part 4:
* Options avaible
I Detergent compartment for prewash cycle
II Detergent compartment for wash cycle
PROGRAM
PREWASH
A
B
C
F
H
N
J
K
P
*
I + II
PROGRAM
NAME
50-90
30-90
-40
-40
40-50
30-40
-40
-30
Delicates
*
*
*
QUICK
WASH
*
*
*
5 kg.
5 kg.
2.5 kg.
2 kg.
1.5 kg.
Normally soiled cottons and linens
FABRIC TYPE
Heavy soiled cottons and linens
Spin for cottons and linens
Heavy and normally soiled
synthetics and synthetic mixture
Woolens
Spin for woolens and delicates
Discharging
Spin for synthetics
DISPENSER
COMPARTMENT
RINSE HOLD
TEMPERATURE (°C)
WHITESCOLOUREDS
LOAD
kg.
Cotton with prewash
Cotton main wash
Cotton spin
Synthetic main wash
Synthetic spin
Delicate wash
Woolen wash
Delicate/ Woolen Spin
Drainage
30-60 30-40 II
II
II
II

Machine operation
Place your clothes into the machine and close the front door. Select the program after
referring to the program selection table. Turn the program selection knob clockwise and
bring the program letter on top.
Adjust the thermostat knob clockwise to set the desired temperature. When the knob
is at “ ” the wash cycle is completed with the tap water temperature. Put powder
detergent and the fabric softener to the compartments and close the detergent dispenser.
11
Push out the knobs before selecting the program and the temparature.After you have finished
the adjustment, you can push the knobs in. This will prevent the knobs from being played by
your children.

You can start the program by pushing On/Off button. Front door will be locked and
the led indicator will go on. When machine is on, the program selection knob turns
clockwise and takes water in. In B program the program selection knob turns fastly
4 steps forward. This does not mean a failure, it is necessary to allow the washing
machine to take the needed amount of water.
If fabric softener is added in the softener compartment, it will be used in the last rinse cycle. If rinse hold is selected, by re-pressing
this button, you can continue the program. If no spin is desired, you may leave the rinse hold button pushed. Turn off the machine,
select the letter P on the program selection knob and turn on the machine. With this operation, water in the machine will be
discharged.
During cotton, synthetic and woolen programs the washing action will stand still on a step before rinse and wash from a period of
10 minutes up to 55 minutes acording to the choosen program. This waiting period does not mean a failure.
12
Machine stops automatically after the programs are completed. Press the On/Off button to turn off your machine. Front door can
be opened 1-2 minutes after the On/Off button is pushed. Turn off the tap. Unload the machine and leave the front door open to air
the machine.
Program can be started by pushing the On/Off button. Front door will be locked
and the led indicator will go on.
Wash programs A, B and Cis finished when the solid line after Con the
program selection knob is on top. If rinse hold button is not pushed, the wash
program F end after delicate spin Hand the wash programs N, Jend after
delicate spin K.
Program operation
End of the program
Unloading the machine

13
To clean the detergent residues, remove the detergent dispenser from its place by pressing on the area marked on siphon.
Wash the dispenser with water and also clean the dispenser housing before inserting the dispenser to its place.
Detergent dispenser
Clean the siphon (coloured piece in the dispenser) every 30-40 washes. Pull out the siphon by holding from its edges. To
prevent clogging, clean the softener residues thoroughly and make sure that the siphon fits into its place completely before any
operation.
Siphon
Care and maintanence
Part 5:

To prevent any leakage, have a technician to control the hoses every
two years. If the machine is placed at cold ambient temperatures,
the water remining inside the pump and hoses should be removed
from the filters. Also to prevent freezing, empty the water intake
hoses by disconnecting from taps.
Hoses
Water intake filter
Drum
14
Do not leave any metal objects (pins, needles, etc.) inside the drum.
These objects may cause rust on the drum surface. Do not clean
the drum with scratching elements.
At the end of the water intake connection module and water inlet
hose-tap side, there exists filters. These filters prevent any dirt and
objects passing into the machine. It is advisable that these filters
should be cleaned every 30-40 washes. To clean the filter, first turn
the tap off. Then, disconnect the hose and clean the filter with a
thin brush. If the filter is very dirty, you may clean it by pulling out
with pliers. To clean the filter at the tap side of the hose, pull it out
by hand and clean the filter under the tap water.

To prevent objects entering to the pump, your machine comes with a filter system
that extends the pump life. It is advisable that you should clean the filter at every
30-40 washes. Before opening the filter door, disconnect the power. Turn the
opening of kick plate screws 90° with a help of screw driver or a coin. Place a
little pan infront of the filter door to prevent a little amount of water spilling from
the machine. Remove the filter by turning it counter-clockwise direction. After
cleaning the objects on the filter, place it by turning clockwise and make sure that
it is closed firmly. Place the kick plate and secure it by locking the screws.
Attention! If the filter does not fit into its place, water will
leak out from the filter.
Cleaning the pump filter
15

Alcoholic baverages: Wipe the fabric first with water, then
water-glycerine solution and rinse with vinegar-water solution.
Shoe polish: Without harming the fabric, remove the stain
carefully and grind it with detergent. If this doesn’t help, prepare
a water to alcohol solution (2 to 1) and rub the fabric, then
wash it with warm water.
Tea and coffee: Pour hot water on to the stain and the fabric
is white, pour some bleach and rinse it with water.
Bubblegum: Harden the gum stain by putting an ice on it.
Then scrape off the stain carefully.
Chocolate and cocoa: Place the fabric into cold water for
a period of time. Rub it with soap or detergent and wash it
with the warmest water that the fabric can withold. If any grease
stain leftover wipe it with oxygen water.
Tomato paste: Scrape the hardened paste and leave the
fabric for 40 minutes into cold water. Rub it with detergent and
wash.
Egg stain: If the stain is hardened scrape the stain and wipe
it with wet sponge or a soft cloth. Rub it with detergent and
wash with cold water.
Grease stain: Scrape the stain and rub it with detergent.
Then wash the fabric with warm water.
Mustard: Use glycerin and rub the fabric with detergent. If
unsuccesful, wipe the stain with alcohol. (Colored and synthetic
fabrics need 2 cups water and 1 cup alcohol solution.)
The following stain removing tips are approximate and can only be used at the washable fabrics.
Please consult the washing information of the fabric manufacturer.
Helpful tips on stain removal
Part 6:
Blood stain: Leave the fabric for30 minutes in the cold water.
Use ammonia solution to remove the stain. (4 liters water-
3 spoonful of ammonia.)
Ice-cream, milk and cream: Place the fabric into cold water
for a period of time. Rub it with soap or detergent and wash it with
the warmest water that the fabric can withold. If any grease stain
leftover wipe it with oxygen water.
Mildew: Do not let mildew stains stay for long periods of time.
Place the fabric into cold water for a period of time. Rub it with
soap or detergent and wash it with the warmest water that the
fabric can withold. If any grease stain leftover wipe it with oxygen
water.
Fruit: Pour cold water on to the stain and do not use warm water
to rinse. Let it sit for 2 hours and wipe it with white vinegar and
rinse.
Ink: Let the cold water run on the stain and wait until the stain is
gone. Later rub it with lemon juice and detergent, let the stain stay
for five minutes and rinse the fabric.
Grass stain: Rub the stain with detergent. If the fabric lets, use
bleachinng element. Wools should be wiped with alcohol.
Paint: Use thinner to remove the stain. Put a cotton cloth on the
wool fabrics. Rub the stain with detergent and rinse with cold water.
Burnt stains: Use bleach if permissable. For wool fabrics place
a oxygen water inserted cotton cloth on the stain and iron.
Rinse completely and wash the fabric.
Ratios are
approximated.
16
BUBBLEGUM
MUSTARD
MILDEW

17
Do not use
bleach
Washing
temperature
Can be washed
at centrifugal
machine
Do not wash
centrifugal
machine
Dry on horizantal
surface
Warm iron
Bleach can
be used Do not machine wash
Line dry
Descriptions of the international textile care label (ITCL) symbols
Cl
60°
No spin
No dry cleaning
You turned the machine on, but the leds are off
on the panel.
Check the grounding on the power cable or a blown fuse.
Check the front door proper closure.
Machine does not take water.
Check the front door for proper closure. Either taps are
closed or water intake filters are clogged.
Taken water is directly discharged.
Check if the discharge hose placed as described in the
users manual or not.
Water coming from beneath the machine.
Check the water intake and drain hoses. Tighten the connections.
The washers of the hoses may be worn out. If non of the both,
the pump filter is not closed properly.
Foam coming out of the detergent dispenser.
Check whether your detergent is suitable for automatic machines.
Next time use less detergent.
Pump does not drain water.
Clean the pump filter. Check whether the drain hose is bent or
not. If there is need to clean the pump filter, refer to the pump
filter cleaning section of the manual.
Before calling service
Part 7:
Chemicals can
be used
Do not wash Dry clean
P A
Iron permitted Do not iron

This product
has been
manufactured at
environmental
friendly modern
facilities.