Archers Sleepcentre HOXTON User manual

PAGE 1
HOXTON 2 DOOR WARDROBE
ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
WARNING AND INSTRUCTIONS
• PLEASE KEEP THE ORIGINAL PACKAGING UNTIL THE ITEM IS FULLY ASSEMBLED AND IN
PLACE. IN THE UNLIKELY EVENT THAT YOU NEED TO RETURN YOUR PRODUCT, IT MUST BE
RETURNED IN ITS ORIGINAL PACKAGING TO AVOID FURTHER DAMAGE. FAILURE TO COMPLY
TO THESE PROCEDURES, NO RETURN’S WILL BE ACCEPTED.
• IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
• DUE TO THE SIZE OF THIS PRODUCT WE RECOMMEND THAT IT IS ASSEMBLED IN THE ROOM INTENDED
FOR USE.
• WHEN YOU ARE READY TO START, MAKE SURE THAT YOU HAVE THE RIGHT TOOLS, PLENTY OF SPACE
AND A CLEAN, DRY AREA FOR ASSEMBLY.
• UNWRAP ALL PACKAGING MATERIALS AND PLACE THE COMPONENTS ON TOP OF THE CARTON BOX OR
ON A CLEAN FLOOR TO PREVENT IT FROM SCRATCHING.
• CHECK THE PACK AND MAKE SURE YOU HAVE ALL THE PARTS LISTED.
• ENSURE THAT THIS PRODUCT IS FULLY ASSEMBLED AS ILLUSTRATED BEFORE USE.
• TOOLS NOT INCLUDED.
• CHECK ALL SCREWS OR BOLTS ARE TIGHTENED AND INSPECT REGULARLY.
• THIS PRODUCT SHOULD ONLY BE USED ON FIRM LEVEL GROUND.
• KEEP SMALL PART OUT OF REACH OF CHILDREN.
• MAKE SURE THE LEGS REMAIN IN CONTACT WITH THE GROUND.
• DO NOT USE POWER TOOLS TO CONSTRUCT THIS PRODUCT.
• DO NOT TIGHTENED SCREWS UNTIL FULLY ASSEMBLED.
• DO NOT OVER TIGHTENED SCREWS OR BOLTS.
• DO NOT USE THIS PRODUCT IF PARTS ARE MISSING, DAMAGE OR WORN.
• DO NOT SIT AND STAND ON THE PRODUCT.
• TO CLEAN WIPE WITH A SPONGE AND WARM SOAPY WATER. DO NOT USE SOLVENT BASED CLEANERS
OR DETERGENTS AS THEY CAN BLEACH OR DAMAGE THE PRODUCT.
• NEVER USE SCOURERS, ABRASIVES OR CHEMICAL CLEANERS.

PAGE 2
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so it
tightens over the bolt.
This is how a cam nut works ........
TWO PERSONS REQIURED TO ASSEMBLE THIS PRODUCT
1. Please check that you have all the parts listed before you start
assembling. If you do find that something is missing, do not
continue assembly. Please contact your supplier immediately.
2. Lay out all of the components on a soft surface as if you were
preparing to do a jigsaw puzzle.
3. Separate and identify each component from the hardware pack
and rest each one in its proper location before fastening.
(Tools not provided)
Use a flat blade screwdriver to tighten the cam
nuts. A quarter turn clockwise is all that is needed.
Lock

PAGE 3
THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
1
2
3
4
5
6
7
8
9
10
11
X1804 X522 19
PARTSNO QTY
2 PCS
X1628 X389 3 2PCS
PARTS LIST
NO DESCRIPTION QTY
HARDWARE LIST
A
B
C
D
E
WOOD DOWEL M8 x 25mm
CB SCREW M3.5 x 16mm
CSK CAP WOOD M6 x 50mm
HANDLE SCREW M4 x 19mm
12
32
4
4
F
HANDLE SCREW M4 x 30mm & WASHER
20
G
H
I
J
K
CAM NUT 15MM
CAM BOLT
CAM CAP
HANDLE
L KEY
33
33
33
2
1
L
V BRACKET
2
M
HINGES 7/8
6
N
METAL ADJUST LEG
1
CB SCREW M3.5 x 12mm
8
O
3MM PVH
1
P
CHROME PIPE
1
9
7
2
1
6
8
10
2
4
3
5
11 12
8
V
W
X
Y
Z
2
2
2
2
4
CB SCREW M3.5 x 16mm
CB SCREW M4 x 38mm
SAFETY STRAP
PLASTIC WALL ANCHOR
WASHER
X768 X90 15 2 PCS
X1618 X519 15 1 PC
X769 X70 15 1 PC
X768 X90 15 1 PC
X769 X481 15 1 PC
X1618 X519 15 1 PC
X800 X520 15 1 PC
X
800
X520 15 1 PC
X1610 X380 15 1 PC
12 X1610 X380 15 1 PC

5
PAGE 4
THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 1
STEP 2
WOOD DOWEL M8 x 25mmA 12
HCAM BOLT
33
16
16
9
7
BOTTOM VIEW
R VIEW L VIEW

G33CAM NUT 15MM
PAGE 5
THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 4
STEP 3
BCB SCREW M3.5 x 16mm 4
LV BRACKET 2
BOTTOM VIEWR VIEW L VIEW
REAR VIEW
2
16
4
3
5
R VIEW L VIEW
16

PAGE 6
THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 5
STEP 6
B 12CB SCREW M3.5 x 16mm
K6HINGES 7/8
D 4HANDLE SCREW M4 x 19mm
J 2HANDLE
REAR VIEW
11 12
11 12

PAGE 7
THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 7
STEP 8
I 20CAM CAP
I
G
H
A
G
I
G
1
6
2
3
2
4
5
1
6
2
7
F 1L KEY
I 3CAM CAP
C 4CSK CAP WOOD M6 x 50mm
H
A
G

PAGE 8
THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 9
STEP 10
8
8
O
I
G
H
A
G
MCB SCREW M3.5 x 12mm 8
9
6
1
P
8
3
8
2
8
8
8
2
M
M
8
I 10CAM CAP
O 13mm PVH
P 1CHROME PIPE

PAGE 9
THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 11
STEP 12
EHANDLE SCREW M4 x 30mm & WASHER 20
BCB SCREW M3.5 x 16mm 12
Adjust door in & out
Adjust door
left & right
B
K
10
10
7
1
6
B
N
11
NMETAL ADJUST LEG
BCB SCREW M3.5 x 16mm 4
1
12

PAGE 10
THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
COMPLETED

PAGE 11
THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
1.
2.
3.
Y
1. First mark the wall with pencil as in diagram.
2. Drill small hole at the pencil mark.
3. Insert plastic wall anchor (Y).
V W X Y Z
x 2 x 2 x 2 x 2 x 4

PAGE 12
THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
4.
5.
4. Add safety strap (X), washer (Z) using 3.5 x 16mm screw (V) to back of cabinet.
5. Finally, attach safety strap (X) and washer (Z) using 4 x 38mm screw (W) to the wall.
V W X Y Z
x 2 x 2 x 2 x 2 x 4
Z
V
X
X
Z
W