Archers Sleepcentre HOXTON COFFEE TABLE WITH DRAWERS User manual

PAGE 1
HOXTON COFFEE TABLE WITH DRAWERS
ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
WARNING AND INSTRUCTIONS
• PLEASE KEEP THE ORIGINAL PACKAGING UNTIL THE ITEM IS FULLY ASSEMBLED AND IN
PLACE. IN THE UNLIKELY EVENT THAT YOU NEED TO RETURN YOUR PRODUCT, IT MUST BE
RETURNED IN ITS ORIGINAL PACKAGING TO AVOID FURTHER DAMAGE. FAILURE TO COMPLY
TO THESE PROCEDURES, NO RETURN’S WILL BE ACCEPTED.
• IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
• DUE TOTHE SIZE OF THIS PRODUCT WE RECOMMEND THAT IT ISASSEMBLED IN THE ROOM INTENDED
FOR USE.
• WHEN YOU ARE READY TO START, MAKE SURE THAT YOU HAVE THE RIGHT TOOLS, PLENTY OF SPACE
AND A CLEAN, DRY AREA FOR ASSEMBLY.
• UNWRAPALL PACKAGING MATERIALSAND PLACE THE COMPONENTS ON TOP OF THE CARTON BOX OR
ON A CLEAN FLOOR TO PREVENT IT FROM SCRATCHING.
• CHECK THE PACKAND MAKE SURE YOU HAVE ALL THE PARTS LISTED.
• ENSURE THAT THIS PRODUCT IS FULLYASSEMBLED AS ILLUSTRATED BEFORE USE.
• TOOLS NOT INCLUDED.
• CHECK ALL SCREWS OR BOLTS ARE TIGHTENEDAND INSPECT REGULARLY.
• THIS PRODUCT SHOULD ONLY BE USED ON FIRM LEVEL GROUND.
• KEEP SMALL PART OUT OF REACH OF CHILDREN.
• MAKE SURE THE LEGS REMAIN IN CONTACT WITH THE GROUND.
• DO NOT USE POWER TOOLS TO CONSTRUCT THIS PRODUCT.
• DO NOT TIGHTENED SCREWS UNTIL FULLY ASSEMBLED.
• DO NOT OVER TIGHTENED SCREWS OR BOLTS.
• DO NOT USE THIS PRODUCT IF PARTSARE MISSING, DAMAGE OR WORN.
• DO NOT SITAND STAND ON THE PRODUCT.
• TO CLEAN WIPE WITH A SPONGEAND WARM SOAPY WATER. DO NOT USE SOLVENT BASED CLEANERS
OR DETERGENTSAS THEY CAN BLEACH OR DAMAGE THE PRODUCT.
• NEVER USE SCOURERS, ABRASIVES OR CHEMICAL CLEANERS.

PAGE 2
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so it
tightens over the bolt.
This is how a cam nut works ........
TWO PERSONS REQIURED TO ASSEMBLE THIS PRODUCT
1. Please check that you have all the parts listed before you start
assembling. If you do find that something is missing, do not
continue assembly. Please contact your supplier immediately.
2. Lay out all of the components on a soft surface as if you were
preparing to do a jigsaw puzzle.
3. Separate and identify each component from the hardware pack
and rest each one in its proper location before fastening.
(Tools not provided) Use a flat blade screwdriver to tighten the cam
nuts. A quarter turn clockwise is all that is needed.
Lock

PAGE 3
THE USE OF POWER TOOLS TOASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
6
6
6
9
7
7
7
7
7
1
34
5
2
4
3
10
1 X1200 X600 15
2 X1200 X600 15
3 X218 X599 15
4 X218 X599 15
5 X400 X218 15
6 X363 X210 30
7 X250 X148 15
8 X313 X148 15
9 X342 X250 3
10 X404 X602 19
PARTSNO QTY
1 PC
1 PC
2 PCS
2 PCS
1 PC
4 PCS
8 PCS
4 PCS
4 PCS
2 PCS
A
B
C
D
E
F
G
H
I
J
K
L
NO DESCRIPTION
M
N
O
QTY
16
52
32
8
8
8
16
16
16
4
1
35
4
4
1
PARTS LIST HARDWRAE LIST
WOOD DOWEL M8 x 25mm
CB SCREW M3.5 x 16mm
CB SCREW M4 x 38mm
CSK CAP WOOD M6 x 50mm
HANDLE SCREW M4 x 19mm & WASHER
HANDLE SCREW M4 x 30mm & WASHER
CAM NUT
CAM BOLT
CAM CAP
HANDLE
L KEY
NAIL 5/8
DRAWER SLIDE 10’’
DRAWER SLIDE 10’’
METALADJUST LEG

PAGE 4
THE USE OF POWER TOOLS TOASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 1
STEP 2
A WOOD DOWEL M8 x 25mm 16
H 16CAM BOLT
3
4
4
3
1BOTTOM VIEW
2
44
R VIEW L VIEW

PAGE 5
THE USE OF POWER TOOLS TOASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 3
STEP 4
G 16
B CB SCREW M3.5 x 16mm 24
M DRAWER SLIDE 10’’ 4
CAM NUT
R VIEW L VIEW R VIEW L VIEW
REAR VIEW
L
R
3443
5
34
43
L VIEW
L VIEW
R VIEW
R VIEW
ML
ML
MR
MR
MR
MR
ML
ML

PAGE 6
THE USE OF POWER TOOLS TOASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 5
STEP 6
C CB SCREW M4 x 38mm 32
L NAIL 5/8 32
78
7
6
78
7
6
78
7
6
78
7
6
99
99

LR
PAGE 7
THE USE OF POWER TOOLS TOASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 7
STEP 8
BCB SCREW M3.5 x 16mm 24
N
DRAWER SLIDE 10’’ 4
E HANDLE SCREW M4 x 19mm & WASHER 8
J HANDLE 4
9
9
9
9
NR
NR
NR
NR
NL
NL
NL
NL
66
6 6
E
J

PAGE 8
THE USE OF POWER TOOLS TOASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 9
STEP 10
I CAM CAP 4
KL KEY 1
I CAM CAP
KL KEY
D CSK CAP WOOD M6 x 50mm
12
1
8
H
G
H
AG
1
2
3
I
G
1
4
4
3
3
5
2
I
G

PAGE 9
THE USE OF POWER TOOLS TOASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 11
STEP 12
B CB SCREW M3.5 x 16mm
F HANDLE SCREW M4 x 30mm & WASHER
O METALADJUST LEG
4
8
1
10
10
GG
B