Arctic King WPPH07CR0N User manual

Portable
WPPH07CR0N
www.midea.com
USER MANUAL
en
PH
Warning notices: Before using
this product, please read this
manual carefully and keep it
for future reference.
The design and specifications
are subject to change without
prior notice for product
improvement. Consult with
your dealer or the manufacturer
for details.
Rated voltage: 115V
Frequency: 60Hz

Page 2
Read This Manual
Inside you’ll find many helpful hints on how to use and maintain your air conditioner
properly. Just a little preventive care on your part can save you a great deal of time
and money over the life of your air conditioner. You’ll find many answers to common
problems in the chart of troubleshooting tips - you should be able to fix most of
them quickly before calling service. These instructions may not cover every possible
condition of use, so common sense and attention to safety is required when installing,
operating and maintaining this product.
• Contactan authorized service technician for repair or maintenance of this unit.
• The air conditioner is not intended for use by young children or infirm persons
without supervision.
• Young children should be supervised to ensure that they do not play with the air
conditioner.
• If the power cord needs to be replaced, please contact our consumer service and
look for an authorized technician.
• Electrical installation must be performed in accordance to national regulation
standards by qualified personnel only.
Owner’s Manual
Safety Precautions ....................................................................................... 3
Unit Specifications and Features .............................................................. 6
Operating Instructions ................................................................................ 7
Installation Instructions ............................................................................... 10
Care and Cleaning ....................................................................................... 15
Troubleshooting Tips .................................................................................. 16
Remote Control Instructions ..................................................................... 17
27
CAUTION
Warranty ...................................................................and Return Policy ...

Page 3
Safety
Precautions
Safety Precautions
Pleaseread through these instructions before you start the installation process.
Improper installation can cause damage to the unit, your personal property, and
also poses a personal safety hazard.
• Installation must beperformed according to the installation instructions.
Improper installation can cause waterleakage, electrical shock, orfire.
• Useonly the included accessories and parts, and specified tools for the
installation. Using non-standard parts can cause water leakage,electrical shock,
fire, and injury or property damage.
• Make sure that the outlet you are using is grounded and has the appropriate
voltage. The power cord is equipped with a three-prong grounding plug to
protect against shock. Voltage information can be found on the sideof the unit,
behind the grille.
• Install the unit on a flat, sturdy surface. Failure to dosocould result in damage
or excessive noise and vibration.
• The unit must bekept free from obstruction to ensure proper functioning and to
mitigate safety hazards.
• DO NOT modify the length of the power cord or use an extension cord to power
the unit. DO NOT share a single outlet with other electrical appliances. Improper
power supply can cause fire or electrical shock.
WARNING
To prevent injury to the user or other people and property damage, the instructions
shown here must be followed. Incorrect operation due to ignoring of instructions may
cause harm or damage. The level of risk is shown by the following indications.
CAUTION
WARNING
This symbol indicatesthe possibility of death or serious injury.
This symbol indicatesthe possibility of injury or damage to property.
This symbol shows that the operation manual should be read carefully.
This symbol shows that a service personnel should be handling this
equipment with reference to the installation manual.
This symbol shows that this appliance uses a flammable refrigerant.
If the refrigerant is leakedandexposed to an external ignition source,
there is a risk of fire.
WARNING
CAUTION
CAUTION
CAUTION
This symbol shows that information is available such asthe operating
manual or installationmanual.

Page 4
Safety
Precautions
WARNING
•DO NOT allow children toplay with the air conditioner. Children must be
supervised around the unit at all times.
• If the air conditioner is knocked over during use, turn off the unit and unplug it
from the main power supply immediately. Visually inspect the unit to ensure there
is no damage. If you suspect the unit has been damaged, contact a technician or
customer service for assistance.
• In a thunderstorm, the unit should be turned off to avoid damage to the machine
due to lightning.
CAUTION
•This applianceis not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities or lack of experience and
knowledge,unless they have been given supervision or instruction concerning
use of theappliance by a person responsible for their safety.
•If thepower cord is damaged, it must bereplaced by the manufacturer, its
service agent or similarly qualified persons in orderto avoid a hazard.
• Prior to cleaning or other maintenance, the appliance must be disconnected
from the supply mains.
• Do not install the appliance in a location that may be exposed tocombustible
gas. If combustible gas accumulates around the unit, it may cause fire.
•Do not runthepower cord under carpeting. Do not cover cord withthrow rugs,
runners, or similarcoverings. Do not route cord under furniture or appliances.
Arrangecord away from traffic area and where it will not be tripped over.
•To reduce the risk of fire or electric shock, do not use this air conditioner with
any solid-statespeed control device.
•The appliance shall be installed in accordance with national wiring regulations.
• Contact the authorized service technician for repair or maintenance of this unit.
• Contact the authorized installer for installation of this unit.
•When there are significant differences between features or operation implied by
the remote control illustration and the actual functions described in the USER
MANUAL, the descriptions in the USER MANUAL shall prevail.
•Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad,ni-mh, etc.)
batteries.
•DO NOT install your air conditioner in a wet room such as abathroom orlaundry
room. Exposure to water can cause electrical components toshort circuit.
•DO NOT install the unit inalocation that may beexposed tocombustible gas,as
this could cause fire.
• The unit has wheels to facilitate moving. Do not attempt to roll the unit across
thick carpet or to roll over objects, as this could causethe unit to tip over.
•DO NOT attempt tooperate a unit that has been dropped or damaged.

Safety
Precautions
Safety Precautions
WARNINGS (for using R32 refrigerant only)
• Do not use any means to accelerate the defrosting process or to clean the unit,
other than those recommended by the manufacturer.
• Do not use or store the appliance in spaces with potential ignition sources (for
example: open flames, an operating gas appliance or an operating electric heater).
• Do not pierce or burn refrigerant tubing. Be aware that refrigerants may not
contain an odor.
• Keep ventilation openings clear of obstruction.
• Store the appliance in a way that will prevent mechanical damage fromoccurring.
• Store the appliance in a well-ventilated area where the roomsize corresponds to
the roomarea as specified for operation.
• Any person who is involved with working on or breaking into a refrigerant circuit
should hold a current valid certificate froman industry-accredited assessment
authority, which authorizes their competence to handle refrigerants safely in
accordance with an industry recognized assessment specification.
• Servicing shall only be performed as recommended by the equipment
manufacturer. Maintenance and repair requiring the assistance of other skilled
personnel shall be carried out under the supervision of the person competent
in the use of flammable refrigerants.
• Flammable refrigerant (R32) is used within the air conditioner. When maintaining
or disposing of the air conditioner, the refrigerant (R32) shall be recovered
properly, do not discharge to air directly.
Caution: Risk of fire/
flammable materials
(Required for R32/R290 units only)
IMPORTANT NOTE: Read this manual
carefully before installing or operating
your new air conditioning unit. Make sure
to save this manual for future reference.
Page 5

Preparation
Design and Compliance Notes
Unit
Specifications
and Features
Design Notice:
In order to ensure the optimal performance of our products, the design specifications of
the unit and remote control are subject to change without prior notice.
Energy Rating Information:
This product is tested in accordance to the DOE SACC capacity energy rating test.
Unit Temperature Range:
Mode Temperature Range
Cool 17°C ~ 35°C (62°F ~ 95°F)
Dry 13°C ~ 35°C (55°F ~ 95°F)
Front Rear
control panel
remote signal receptor handle
(both sides)
horizontal louver control
lever (adjust manually)
NOTE: PHA cannot be
adjusted.
NOTE: PHA cannot be
adjusted.
vertical louver control
lever (adjust manually)
panel
Caster
bottom tray
drain outlet
air filter
(behind the grille)
upper air intake
air outlet
lower air intake
drain outlet
Exhaust Hose Installation:
The exhaust hose and adaptor must be installed or removed in accordance with the
usage mode.
For COOL mode must be installed exhaust hose.
For FAN or DEHUMIDIFY mode must be removed exhaust hose.
Unit Specifications and Features
Page 6

Operating
Instructions
Control Panel Features
Mode button
Selects the desired operating mode.
Each time you press the button, a mode
is selected in a sequence that goes from
COOL, FAN and DRY. The mode light
illuminates and indicates the selected
mode.
Up (+) and Down (-) buttons
Used to adjust (increasing/decreasing)
temperature settings in 1°C/1°F increments
in a range of 17°C/62°F to 30°C/86°F.
NOTE
The control is capable of displaying
temperature in degrees Fahrenheit or
degrees Celsius. To convert fromone
to the other, press and hold the Up
and Down buttons at the same time
for 3 seconds.
NOTE
On above modes, the unit operates
the auto fan speed automatically. You
can set fan speed only by the remote
controller on COOL and FAN modes.
Power button
Power switch on/off.
Power
indicator light
Timer mode indicator
light (set only by
remote controller)
LED display
Shows the set
temperature while on cool
mode. While on DRY and
FAN modes, it shows the
room temperature.
NOTE
When one of the above malfunctions
occurs, turn off the unit and check for
any obstructions. Restart the Unit. If the
malfunction persists, turn off the unit
and unplug the power cord. Contact
the manufacturer or its service agents
or a similar qualified person for service.
LED Display
Up (+) and Down (-) Control
Mode
Selector
Power
Button
Shows Error codes:
E1 - Room temperature sensor error.
E2 - Evaporator temperature sensor error.
E3 - Condenser temperature sensor error.
E4 - Display panel communication error.
Shows protection code:
P1 - Bottom tray is full - Connect the drain
hose and drain the collected water
away. If protection code repeats, call
for service.
Operating Instructions
Page 7

Operating
Instructions
COOL operation
• Press the “MODE” button until the “COOL”
indicator light comes on.
• Press the ADJUST buttons “+” or “-” to
select your desired room temperature. The
temperature can be set within a range of
17°C~30°C/62°F~86°F.
• Press the “FAN SPEED” button to choose
the fan speed.
DRY operation
• Press the “MODE” button until the “DRY”
indicator light comes on.
•While in this mode, you cannot select a
fan speed or adjust the temperature. The
fan motor operates at LOW speed.
• Keep windows and doors closed for the
best dehumidifying effect.
•Do not connect the duct to a window.
FAN operation
• Press the “MODE” button until the ”FAN“
indicator light comes on.
• Press the “FAN SPEED” button to choose
the fan speed. The temperature cannot
be adjusted.
•Do not connect the duct to a window.
Operating Instructions
SLEEP/ECO operation
This feature can be activated from
the remote control ONLY. To activate
SLEEP feature, the set temperature will
increase by 1°C/2°F in 30 minutes. The set
temperature will then increase by another
1°C/2°F after an additional 30 minutes.
This new temperature will be maintained
for 7 hours before it returns to the
originally selected temperature. This ends
the Sleep mode and the unit will continue
to operate as originally programmed.
NOTE
This feature is unavailablein FAN or
DRY mode.
Other Features
NOTE
This feature can be activated from
the remote control ONLY. The remote
control serves as a remote thermostat
allowing for the precise temperature
control at its location.
FOLLOW ME/TEMP SENSING
Feature (optional)
To activate the Follow Me/Temp Sensing
feature, point the remote control towards
the unit and press the Follow Me/Temp
Sensing button. The remote display is
actual temperature at its location. The
remote control will send this signal to the
air conditioner every 3 minutes interval
until press the Follow Me/Temp Sensing
button again. If the unit does not receive
the Follow Me/Temp Sensing signal during
any 7 minutes interval, the unit will exit the
Follow Me/Temp Sensing mode.
Constant Fan button
In cooling or Dry mode, press the button
for 3 seconds to turn on or off the
constant fan function. When the function
is turned on, the constant fan light will
illuminate, identifying the fan continuous
run for cooling. When the function is
turned off, the constant fan light will go
out, identifying the fan cycle run with
compressor stop.
AUTO-RESTART
If the unit breaks off unexpectedly due
to the power cut, it will restart with the
previous function setting automatically
when the power resumes.
WAIT 3 MINUTES BEFORE RESUMING
OPERATION
After the unit has stopped, it can not be
restarted operation in the first 3 minutes.
This is to protect the unit. Operation will
automatically start after 3 minutes.
AIRFLOW DIRECTION ADJUSTMENT
Adjust the air flow direction manually:
- The louver can be set to the desired
position manually.
- Do not place any heavy objects or
other loads on the louver, doing so will
cause damage to the unit.
- Keep the louver fully opened during
operation.
Page 8

NOTE
Make sure the hose is secure so there are
no leaks. Direct the hose toward the
drain, making sure that there are no kinks
that will stop the water flowing. Place the
end of the hose into the drain and make
sure the end of the hose is down to let
the water flow smoothly. When the
continuous drain hose is not used, ensure
that the drain plug and knob are installed
firmly to prevent leakage.
Water drainage
• During dehumidifying modes, remove the drain
plug from the back of the unit and install the drain
connector (5/8” universal female mender) with 3/4”
hose (locally purchased). For models without drain
connector, just attach the drain hose to the hole. Place
the open end of the hose directly over the drain area in
your basement floor.
Remove the
drain plug
Continuous
drain hose
• When the water level of the bottom tray reaches
a predetermined level, the unit beeps 8 times.
The digital display shows “P1.” At this time the
air conditioning/dehumidification process will
immediately stop. However, the fan motor will
continue to operate (this is normal). Carefully move
the unit to a drain location, remove the bottom
drain plug and let the water drain away. Reinstall
the bottom drain plug and restart the machine until
the “P1” symbol disappears. If the error repeats, call
for service.
Bottom drain plug
NOTE
Be sure to reinstall the bottomdrain plug firmly to
prevent leakage before using the unit.
Operating
Instructions
Page 9

Installation
Instructions
Your installation location should meet the following
requirements:
• Make sure that you install your unit on an even surface
to minimize noise and vibration.
• The unit must be installed near a grounded plug, and
the Collection Tray Drain (found on the back of the
unit) must be accessible.
• The unit should be located at least 30 cm (12”) from
the nearest wall to ensure proper air conditioning.
The horizontal louver blade should be at least 50cm
(19.7”) away from obstacles.
• DO NOT cover the Intakes, Outlets or Remote Signal
Receptor of the unit, as this could cause damage to
the unit.
Choosing the Right Location
Recommend Installation
Note About Fluorinated Gasses
• This air-conditioning unit is a hermetically sealed unit that contains fluorinated
gasses. For specific information on the type of gas and the amount, please refer
to the relevant label on the unit itself.
• Service, maintenance and repair of this unit must be performed by a certified
technician.
• Product recycling must be done according to local regulations.
NOTE
All the illustrations in the manual are for explanation
purpose only. Your machine may be slightly different.
The unit can be controlled by the unit control panel
alone or with the remote controller. See the
<<Remote Controller Instruction>> for details.
50cm
19.7inch
Installation Instructions
50cm
19.7inch
Page 10

Installation
Instructions
Page 11
• Medium Phillips screwdriver
• Tape measure or ruler
• Knife or scissors
• Saw (optional, to shorten window adaptor for narrow windows).
Your Window Installation Kit fits windows 67.5-123 cm (26.5”-48”) and can be shortened
for smaller windows.
Tools Needed
Accessories
Part Description
Unit adaptor
Window slider adaptor
Window slider A
Window slider B
Exhaust hose
Bolt
Foamseal A (adhesive)
Foamseal B (adhesive)
Foamseal C (Non-adhesive)
Security bracket and 2 screws
Drain hose
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
2 pc
2 pc
1 set
1 set
Quantity
Remote controller and batteries
(For remote control models only)
TEMP

Installation
Instructions
Step One: Preparing the exhaust hose
assembly
Press the exhaust hose into the window
slider adaptor and unit adaptor, clamp
automatically by elastic buckles of the
adaptors.
Step Two: Install the exhaust hose
assembly to the unit
Push the Exhaust hose into the air
outlet opening of the unit along the
arrow direction.
Step Three: Preparing the adjustable
window slider
1. Depending on the size of your window,
adjust the size of the window slider.
2. If the length of the window requires
two window sliders, use the bolt to
fasten the window sliders once they
are adjusted to the proper length.
Window Installation Kit
Unit
adaptor
Window slider
adaptor
Exhaust hose Exhaust hose
assembly
NOTE
Once the Exhaust Hose assembly and
Adjustable Window Slider are prepared,
choose fromone of the following two
installation methods.
Page 12
Hung Window Sliding Window
Windows Type
Window slider A Window slider B
Bolt
Window
slider A
Window
slider A

Window Installation Kit (cont.)
Type 1: Hung window installation
1. Cut the adhesive foam seal A and B strips to the
proper lengths, and attach them to the window sash
and frame as shown.
Foamseal B
(Adhesive type-shorter)
Foam
seal A
(Adhesive
type)
Window
slider A
Window
slider B
(if required)
Foamseal C
(Non-adhesive type)
Security Bracket
2 Screws
2. Insert the window slider assembly into the window
opening.
3. Cut the non-adhesive foam seal C strip to match the
width of the window. Insert the seal between the glass
and the window frame to prevent air and insects from
getting into the room.
4. If desired, install the security bracket with 2 screws as
shown.
5. Insert the window slider adaptor into the hole of the
window slider.
Installation
Instructions
Page 13

Type 2: Sliding window installation
1. Cut the adhesive foam seal A and B strips to the
proper lengths, and attach them to the window sash
and frame as shown.
Window slider A
Window slider B
(if required)
Foam seal B
(Adhesive
type-shorter)
Foam seal A
(Adhesive
type)
Foam seal C
(Non-adhesive type)
2 Screws
Security
Bracket
2. Insert the window slider assembly into the window
opening.
3. Cut the non-adhesive foam seal C strip to match the
window height. Insert the foam seal between the glass
and the window frame to prevent air and insects from
getting into the room.
4. If desired, install the security bracket with 2 screws
as shown.
5. Insert the window slider adaptor into the hole of the
window slider.
NOTE
To ensure proper functioning, DO NOT overextend or bend the hose. Make sure that there
is no obstacle around the air outlet of the exhaust hose (inthe range of 500mm) in order
for the exhaust system to work properly.All illustrations inthis manual are for explanation
purposes only. Your air conditioner may beslightly different. The actual shape shall prevail.
Installation
Instructions
Page 14

Safety Precautions
Clean the Air Filter
Clean the Unit
Store the Unit When Not in Use
Care and
Cleaning
Maintenance Tips
• Be sure to clean the air filter every 2 weeks for
optimal performance.
• The water collection tray should be drained
immediately after P1 error occurs, and before
storage to prevent mold.
• In households with animals, you will have to
periodically wipe down the grill to prevent
blocked airflow due to animal hair.
• Always unplug the unit before cleaning or servicing.
• DO NOT use flammable liquids or chemicals to clean the unit.
• DO NOT wash the unit under running water. Doing so causes electrical danger.
• DO NOT operate the machine if the power supply was damaged during cleaning.
A damaged power cord must be replaced with a new cord from the manufacturer.
Clean the unit using a damp, lint-free cloth and mild detergent. Dry the unit with a dry,
lint-free cloth.
• Drain the unit’s water collection tray according to the instructions in the following section.
• Run the unit on FAN mode for 12 hours in a warm room to dry it and prevent mold.
• Turn off the unit and unplug it.
• Clean the air filter according to the instructions in the previous section. Reinstall the
clean, dry filter before storing.
• Remove the batteries from the remote control.
NOTE
Be sure to store the unit in a cool, dark place. Exposure to direct sunlight or extreme
heat can shorten the lifespan of the unit.
Remove the air filter
Air filter
(take out)
CAUTION
DO NOT operate the unit without filter because
dirt and lint will clog it and reduce performance.
Care and Cleaning
Page 15

Please check the machine according to the following table before calling for service:
Troubleshooting
Tips
ProblemPossible Cause Troubleshooting
Unit does not
turn on when
pressing ON/
OFF button
P1 Error Code. The water collection tray is full.
Turn off the unit, drain the water
from the water collection tray
and restart the unit.
In COOL mode: room temperature
is lower than the set temperature.
Reset the temperature.
Unit does not
cool well
The air filter is blocked with dust
or animal hair.
Turn off the unit and clean the
filter according to instructions.
Exhaust hose is not connected or
is blocked.
Turn off the unit, disconnect the
hose, check for blockage and
reconnect the hose.
The unit is low on refrigerant. Call a service technician to
inspect the unit and top off
refrigerant.
Temperature setting is too high. Decrease the set temperature.
The windows and doors in the
room are open.
Make sure all windows and doors
are closed.
The room area is too large. Double-check the cooling area.
There are heat sources inside the
room.
Remove the heat sources if
possible.
The unit is
noisy and
vibrates too
much
The floor is not level. Place the unit on a flat, level
surface.
The air filter is blocked with dust
or animal hair.
Turn off the unit and clean the
filter according to instructions.
The unit makes
a gurgling
sound
This sound is caused by the flow
of refrigerant inside the unit
This is normal.
Malfunction Diagnosis
Troubleshooting Tips
Page 16

Operating
Instructions
(With Remote)
Using The Remote Control
Location of the remote controller
Use the remote controllerwithin a distance of8 meters
/ 26 feet from the appliance, pointing it towards the
receiver. Reception is confirmed by a beep.
CAUTION
• The air conditioner will not operate if curtains, doors
or other materials block the signals from the remote
controller to the indoor unit.
• Prevent any liquid from falling into the remote
controller. Do not expose the remote controller to
direct sunlight or heat.
• If the infrared signal receiver on the indoor unit is
exposed to direct sunlight, the air conditioner may
not function properly. Use curtains to prevent the
sunlight from falling on the receiver.
• If other electrical appliances react to the remote
controller, either move these appliances or call
customer support.
8m
TEMP
Remote Control Instructions
Remote Control Specifications
Model RG57H3(B)/BGCEFU1-M
Rated voltage 3.0V (Dry batteries R03/LR03x2)
Signal receiving range 8 m (approx. 26 ft.)
Environment -5°C ~ 60°C (23°F ~ 140°F)
Page 17

Operating
Instructions
(With Remote)
Function Buttons
Before you begin using your new air conditioner, make sure to familiarize yourself with
its remote control. The following is a brief introduction to the remote control itself. For
instructions on how to operate your air conditioner, refer to the Operating Instructions
section of this manual.
O N /O F F
T E MP
SHORT
CU T
TIMER
ON
TIMER
OFF
MODE
FAN
LED
SL EEP
FOLLOW
ME
SHORT CUT
Sets and activates your favorite pre-settings.
ON/OFF
Turns the unit on or off.
TEMP
Increases temperature in 1°C (1°F) increments.
Max. temperature is 30°C (86°F).
TIMER ON
Sets timer to turn unit on (see How to Use
Basic Functions for instructions)
TIMER OFF
Sets timer to turn unit off (see How to Use
Basic Functions for instructions)
LED
Turns indoor unit’s LED display on and off.
If you are sensitive to light while sleeping,
you can press the LED button to turn off the
LED display on the unit. Press the button
again to turn it back on.
FOLLOW ME
Temperature sensing and room
temperature display button.
SLEEP
Saves energy during
sleeping hours.
Optional
TEMP
Decreases temperature in 1°C (1°F) increments.
Min. temperature is 17°C (62°F).
NOTE: Pressing and hold and buttons
together for 3 seconds will alternate the
temperature display between the °C &°F scale.
FAN SPEED
Selects fan speeds in the
following order:
AUTO LOW MEDHIGH
MODE
Scrolls through operation modes
as follows:
AUTO COOL DRY HEAT FAN
NOTE:
Please do not select HEAT mode
if the machine you purchased is
cool-only type. Heat mode is not
supported by the cool-only models.
Page 18

Operating
Instructions
(With Remote)
NOT SURE WHAT A FUNCTION DOES?
Refer to the Operating Instructions section of this manual for a detailed description of
how to use your air conditioner.
INSERTING AND REPLACING BATTERIES
Your air conditioning unit comes with two AAA batteries.
Insert the batteries in the remote control before use.
1. Slide the back cover of the remote control downward,
exposing the battery compartment.
2. Insert the batteries, paying attention to align the (+)
and (-) ends of the batteries with the symbols inside
the battery compartment.
3. Slide the battery cover back into place.
BATTERY DISPOSAL
Do not dispose of batteries as unsorted municipal waste.
Refer to local laws for proper disposal of batteries.
TIPS FOR USING REMOTE CONTROL
• The remote control must be used within 8 meters /
26 feet of the unit.
• The unit will beep when remote signal is received.
• Curtains, other materials and direct sunlight can
interfere with the infrared signal receiver.
• Remove batteries if the remote will not be used more
than 2 months.
Handling the Remote Control
SPECIAL NOTE
Button designs on your unit may differ slightly fromthe example shown.
If the unit does not have a particular function, pressing that function’s button on the
remote control will have no effect.
When there are significant differences between features or operation implied by the
remote control illustration and the actual functions described in the USER’S MANUAL,
the descriptions in the USER’S MANUAL shall prevail
BATTERY NOTES
For optimum product performance:
• Do not mix old and new batteries, or batteries of
different types.
• Do not leave batteries in the remote control if you
don’t plan on using the device for more than 2
months.
Page 19

Operating
Instructions
(With Remote)
Remote LED Screen Indicators
AUTO
COOL
DRY
HEAT
FAN
Transmission Indicator
Lights up when remote sends signal to unit
MODE display
Displays the current
mode, including:
TIMER ON display
Displays when
TIMER ON is set
TIMER OFF display
Displays when
TIMER OFF is set
ECO display
Not available on this unit
Battery display
Low battery detection
Not available on this unit
SLEEP display
Displays when SLEEP
function is activated
SILENT display
Not available on this unit
FAN SPEED display
Displays selected FAN SPEED:
HIGH
MED
LOW
This display is blank when
set to AUTO speed.
Temperature/Timer display
Displays the set temperature by default, or timer setting
when using TIMER ON/OFF functions:
- Temperature range: 17-30°C (62°F-86°F)
- Timer setting range: 0-24 hours
This display is blank when operating in FAN mode.
FOLLOW ME display
Indicates that the FOLLOW
ME function is on
ON/OFF display
Appears when the unit is turned on and disappears when it is turned off
Page 20