Arctic King MPPH-08CRN1-BI01 User manual

Model/modèle :
information about this product, please call our toll-free number.
SAVE THIS MANUAL
Keep this manual and the original sales invoice in a safe, dry place for future reference.
Notre personnel du service à la clientèle est disponible pour vous aider. En cas de problème avec votre achat, ou pour
obtenir plus d’informations à propos de ce produit, veuillez composer notre numéro sans frais.
CONSERVEZ CE GUIDE
Conservez ce manuel avec la facture d’origine dans un endroit sûr et sec pour référence future.
Our customer service staff is available to help you. For any problem with your purchase, or to receive further
Customer Service / Service à la clientèle:
PORTABLE AIR CONDITIONER
Operator's manual
87795056
MPPH-08CRN1-BI01
87795049
MPPH-10CRN1-BI0
87795057
MPPH-10CRN1-BI0B
1-866-206-0888
87795064
MPPHB-12CRN1-BH9B

Preparation.............................................................................................................................................2
Safety Precautions.................................................................................................................................4
Cautions..................................................................................................................................................5
Installation..............................................................................................................................................6
Operation..............................................................................................................................................10
Maintenance....................................................................................................................................... .12
Troubleshooting ..................................................................................................................................13
Design and Compliance Notes...........................................................................................................14
TABLE OF CONTENTS
1
Air Conditioner Limited Warranty...........................................................................................................26
REMOTE CONTROL INSTRUCTIONS.................................................................................................15

Preparation
2
rear
front
bottom tray
drain outlet
handle
(both sides)
air filter
(behind the grille)
upper air intake
air outlet
lower air intake
drain outlet
control panel
remote signal receptor
horizontal louver control
lever(adjustable manually)
NOTE: PHA can not be
adjusted.
NOTE: PHA can not be
adjusted.
vertical louver control
lever(adjustable manually)
panel
Caster

3
Safety Precautions
-Installation must be performed according to the installation instructions. Improper installation
can cause water leakage, electrical shock, or fire.
-Use only the included accessories and parts, and specified tools for the installation. Using
non-standard parts can cause water leakage, electrical shock, fire, and injury or property
damage.
-Make sure that the outlet you are using is grounded and has the appropriate voltage. The
power cord is equipped with a three-prong grounding plug to protect against shock. Voltage
information can be found on the side of the unit, behind the grille.
-Install the unit in on a flat, sturdy surface. Failure to do so could result in damage or excessive
noise and vibration.
-The unit must be kept free from obstruction to ensure proper function and to mitigate safety
hazards.
-DO NOT modify the length of the power cord or use an extension cord to power the unit.
DO NOT share a single outlet with other electrical appliances. Improper power supply can
cause fire or electrical shock.
-DO NOT install your air conditioner in a wet room such as a bathroom or laundry room. Too
much exposure to water can cause electrical components to short circuit.
-DO NOT install the unit in a location that may be exposed to combustible gas, as this could
cause fire.
-The unit has wheels to facilitate moving. Make sure not to use the wheels on thick carpet or
to roll over objects, as these could cause tipping.
-DO NOT operate a unit that has been dropped or damaged.
-Only use the included accessories and specified parts for installation. Using non-standard
parts can cause water leakage, electrical shock, fire, and injury or property damage.
-The unit must be kept free from obstruction to ensure proper function.
-DO NOT allow children to play with the air conditioner. Children must be supervised around
the unit at all times.
-If the air conditioner is knocked over during use, turn off the unit and unplug it from the main
power supply immediately. Visually inspect the unit to ensure there is no damage. If you
suspect the unit has been damaged, contact a technician or customer service for assistance.
-In a thunderstorm, the power must be cut off to avoid damage to the machine due to lightning.
Please read through these instructions before you start the installation process.
Improper installation can cause damage to the unit, your personal property, and
also poses a personal safety hazard.

4
Cautions
-This appliance is not intended for use by people (including children) with reduced physical,
sensory or mental capabilities or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
-Children should be supervised to ensure that they do not play with the appliance.
-If the supply cord is damaged, it must be replaced by the manufacturer,its service agent or
similarly qualified persons in order to avoid a hazard.
-Prior to cleaning or other maintenance, the appliance must be disconnected from the supply mains.
-Do not install the appliance in a location that may be exposed to combustible gas.
-If combustible gas accumulates around the unit, it may cause fire.
-Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings.
-Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it
will not be tripped over.
-Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized
service facility for examination and/or repair.
-To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control
device.
-The appliance shall be installed in accordance with national wiring regulations.
-Contact the authorised service technician for repair or maintenance of this unit.
-Contact the authorised installer for installation of this unit.
-When there are wide differences between "USER' S MANUAL" and "Remote controller
Illustration" regarding functional descriptions, the description in "USER' S MANUAL " shall prevail.
-Do not operate your air conditioner in a wet room such as a bathroom or laundry room.

5
Installation
Choosing The Right Location
Your installation locationshould meetthe following
requirements:
-Make sure that you install your unit on an even
surface to minimize noise and vibration.
-The unit must be installed near a grounded plug,
and the Collection Tray Drain (found on the back
of the unit) must be accessible.
-The unit should be located at least 30cm (12”) from
the nearest wall to ensure proper air conditioning.
-DO NOT cover the intakes, outlets or remote
signal receptors of the unit, as this could cause
damage to the unit.
Note About Fluorinated Gasses
-This air-conditioning unit is a hermetically sealed unit that contains fluorinated gasses.
For specific information on the type of gas and the amount, please refer to the relevant label
on the unit itself.
-Installation, service, maintenance and repair of this unit must be performed by a certified
technician.
-Product uninstallation and recycling must be performed by a certified technician.
-If the system has a leak-detection system installed, it must be checked for leaks at least
every 12 months.
-When the unit is checked for leaks, proper record-keeping of all checks is strongly
recommended.
All the illustrations in the manual are for explanation purposes only. Your machine may be
slightly different. The actual shape shall prevail.The unit can be controlled by the unit control
panel alone or with the remote controller.
NOTE:

6
Installation
Tools Needed
-Medium Philips screwdriver; -Tape measure or ruler; -Knife or scissors;
-Saw (optional, to shorten window adaptor for narrow windows)
Accessories
Your Window Installation Kit fits windows 67.5-123cm (26.5-48”) and can be shortened for
smaller windows.
Window Installation Kit
Press the exhaust hose into
the window slider adaptor
and unit adaptor, clamp
in place with elastic
buckles of the adaptors.
Push the Exhaust hose
into the air outlet opening
of the unit along the arrow
direction.
Step One: Preparing the
Exhaust Hose assembly
Step Two: Install the
Exhaust hose assembly
to the unit
Step Three: Preparing
the Adjustable Window
Slider
1. Depending on the size of
your window, adjust the
size of the window slider.
2. If the length of the window
requires two window sliders,
use the bolt to fasten the
window sliders once they
are adjusted to the proper
length.
Window slider A Window slider B
Bolt
Part Description
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
2 pc
2 pc
1 set
1 set
Unit Adaptor
Window Slider Adaptor
Window Slider A
Window Slider B and C
Exhaust Hose
Bolt
Foam Seal A (Adhesive)
Foam Seal B (Adhesive)
Foam Seal C (Non-adhesive)
Security Bracket and 2 Screws
Drain Hose
Quantity
Remote Controller and Battery
(For remote control models only)
DOM E
EEL
S P EL D
COLC K
ECNA
C L
EMIT R
N
AF
ESER T
COL K
KC
OLC
C
NO
FF
O
TTES EMP.
DEEP
S
NAF
TU
AO
F
NI
W
S G
BRUT O
FOLLOW ME
Unit adaptor Window slider
adaptor
Exhaust hose Exhaust hose
assembly
Window slider C
Bolt

7
Installation
Note: Once the Exhaust Hose assembly and Adjustable Window Slider are prepared,
choose from one of the following two installation methods.
Cut the adhesive foam seal A
and B strips to the proper
lengths, and attach them to
the window sash and frame
as shown.
Cut the adhesive foam seal A
and B strips to the proper
lengths, and attach them to
the window sash and frame
as shown.
Cut the non-adhesive foam
seal C strip to match the width
of the window. Insert the seal
between the glass and the
window frame to prevent air
and insects from getting into
the room.
If desired, install the security
bracket with 2 screws as
shown.
Insert the window slider adaptor
into the hole of the window slider.
Insert the window slider
assembly into the window
opening.
Insert the window slider
assembly into the window
opening.
Type 1: Hung Window Installation
Foam seal B
(Adhesive type-shorter)
2 Screws
Security Bracket
Foam seal A
(Adhesive type)
Window slider A
Window slider B
(if required)
Type 2: Sliding Window Installation
Foam seal B
(Adhesive type-shorter)
Foam seal A
(Adhesive type)
Window slider A
Window slider B
(if required)
Foam seal C
(Non-adhesive type)
Cut the non-adhesive foam
seal C strip to match the
window height. Insert the foam
seal between the glass and the
window frame to prevent air
and insects from getting into
the room.
Foam seal C
(Non-adhesive type)

Installation
8
If desired, install the security
bracket with 2 screws as shown.
Insert the window slider adaptor
into the hole of the window slider.
2 Screws
Security
Bracket
Note: To ensure proper function, DO NOT overextend or bend the hose. Make
sure that there is no obstacle around the air outlet of the exhaust hose (in the
range of 500mm) for the exhaust system to work properly. All the
illustrations in this manual are for explanation purposes only. Your air
conditioner may be slightly different. The actual shape of your unit shall prevail.

Operation
9
MODE button
Selects the appropriate operating
mode. Each time you press the
button, a mode is selected in a
sequence that goes from COOL,
FAN and DRY .The mode indicator
light illuminates under the different
mode setting.
Used to adjust (increasing/decreasing)
temperature settings in 1°C/1°F
increments in a range of 17°C/62°F to
30°C/86°F.
Power button
Power switch on/off.
Power
indicator light
Timer mode indicator
light (set only by
remote controller)
Up (+) and Down
(-) buttons
LED display
Shows the set temperature while on cool
mode. While on DRY and FAN modes, it
shows the room temperature.
Shows error codes:
E1-Room temperature sensor error.
E2-Evaporator temperature sensor error.
E4-Display panel communication error.
Shows protection code:
P1-Bottom tray is full--Connect the drain
hose and drain the collected water away.
If protection repeats,call for service.
Note: When one of the above
malfunctions occurs, turn off the unit,
and check for any obstructions.
Restart the unit; if the malfunction is
still present, turn off the unit and
unplug the power cord. Contact the
manufacturer or its service agents or
a similar qualified person for service.
NOTE: On above modes, the unit
operates the fan speed
automatically. You can set fan
speed only by the remote controller
on COOL and FAN modes.
NOTE: The display can show
temperature in degrees
Fahrenheit or degrees Celsius.
To convert from one to the other,
press and hold the Up and Down
buttons at the same time for 3
seconds.

Operation
10
Operation Instructions
COOL operation
-Press the "MODE" button until the "COOL" indicator light comes on.
-Press the ADJUST buttons "+" or "-" to select your desired room temperature. The temperature
can be set within a range of 17°C~30°C/62°F~86°F.
-Press the "FAN SPEED" button to choose the fanspeed.
DRY operation
-Press the "MODE" button until the "DRY" indicator light comes on.
-Under this mode, you cannot select a fan speed or adjust the temperature. The fan motor
operates at LOW speed.
-Keep windows and doors closed for the best dehumidifying effect.
-Do not put the duct to the window.
FAN operation
-Press the "MODE" button until the"FAN " indicator light comes on.
-Press the "FAN SPEED" button to choose the fan speed. The temperature can not be adjusted.
-Do not put the duct to the window.
SLEEP/ECO operation
This feature can be activated from the remote control ONLY. To activate SLEEP feature, the set
temperature will increase by 1°C/1°F) in 30 minutes. The set temperature will then increase by
another 1°C/1°F) after an additional 30 minutes. This new temperature will be maintained for 7
hours before it returns to the originally selected temperature. This ends the Sleep mode and the
unit will continue to operate as originally programmed.
Other features
NOTE: This feature is unavailable under FAN or DRY mode.
NOTE:This feature can be activated from the remote control ONLY. The remote control
serves as a remote thermostat allowing for the precise temperature control at its location.
To activate the Follow Me/Temp Sensing feature, point the remote control towards the unit
and press the Follow Me/Temp Sensing button. The remote displays the actual temperature
at its location. The remote control will send this signal to the air conditioner every 3
minutes until you press the Follow Me/Temp Sensing button again. If the unit does
not receive the Follow Me/Temp Sensing signal for 7 consecutive minutes, the unit
will beep to indicate the Follow Me/Temp Sensing mode has ended.
FOLLOW ME/TEMP SENSING feature(optional)

Operation
11
AUTO-RESTART
IIn the event of an unexpected power outage, the unit will automatically restart with the previous
settings when the power resumes.
WAIT 3 MINUTES BEFORE RESUMING OPERATION
After the unit has stopped, it can not be restarted for the first 3 minutes. This is to protect the
unit. Operation will automatically start after 3 minutes.
AIR FLOW DIRECTION ADJUSTMENT
Adjust the air flow direction manually:
-The louvers can be set to the desired position manually.
-Do not place any heavy objects or other loads on the louvers, doing so will cause damage to
the unit.
-Ensure the louvers are fully opened under heating operation.
-Keep the louvers fully opened during operation.
Water drainage
-Under dehumidifying modes, remove the drain plug from the back of the unit, install the drain
connector(5/8" universal female mender) with 3/4" hose (sold separately). For the models
without drain connector, just attach the drain hose to the hole. Place the open end of the hose
directly over the drain area in your basement floor.
Remove the
drain plug
Continuous
drain hose
-When the water level of the bottom tray
reaches a predetermined level, the unit beeps 8 times, the
digital display area shows "P1" . At this time the air
conditioning/dehumidification process will immediately stop.
However, the fan motor will continue to operate (this is normal).
Carefully move the unit to a drain location, remove the bottom
drain plug and let the water drain away. Reinstall the bottom
drain plug and restart the machine until the "P1" symbol
disappears. If the error repeats, call for service.
Bottom drain
plug
NOTE:When the continuous drain hose is not used, ensure that the drain plug and
knob are installed firmly in the air conditioner to prevent leakage.
NOTE: Be sure to reinstall the bottom drain plug firmly to
prevent leakage before using the unit.

Maintenance
12
Safety Precautions
Maintenance Tips
-Always unplug the unit before cleaning or servicing.
-DO NOT use flammable liquids or chemicals to clean the unit.
-DO NOT wash the unit under running water. Doing so causes electrical danger.
-DO NOT operate the machine if the power supply was damaged during cleaning. A damaged power cord
must be replaced with a new cord from the manufacturer.
Clean the Air Filter
Clean the Unit
Store the unit when not in use
-Be sure to clean the air filter every 2 weeks for
optimal performance.
-The water collection tray should be drained
immediately after P1 error occurs, and before storage
to prevent mold.
-In households with animals, you will have to
periodically wipe down the grill to prevent blocked
airflow due to animal hair.
Remove the air filter
Air filter
(take out)
Clean the unit using a damp, lint-free cloth and mild detergent. Dry the unit with a dry lint-free cloth.
-Drain the unit’s water collection tray according to the instructions previous section.
-Run the appliance on FAN mode for 12 hours in a warm room to dry it and prevent mold.
-Turn off the appliance and unplug it.
-Clean the air filter according to the instructions in the previous section.
Reinstall the clean, dry filter before storing.
-Remove the batteries from the remote control.
Be sure to store the unit in a cool, dark location. Exposure to direct sunshine or extreme
heat can shorten the lifespan of the unit.

Troubleshooting
13
Please check your air conditioner according to the following form before
asking for maintenance:
Problem Possible Cause Troubleshooting
Unit does not turn on
when pressing
ON/OFF button
P1 Error Code
Reset the temperature
Turn off the unit and clean the filter
according to instructions
Turn off the unit, disconnect the hose,
check for blockage and reconnect the
hose
Call a service technician to inspect the
unit and top off refrigerant
Decrease the set temperature
Make sure all windows and doors are
closed
Turn off the unit and clean the filter
according to instructions
Double-check the cooling area
Remove the heat sources if possible
Place the unit on a flat, level surface
This is normal
In COOL mode:
room temperature is lower
than the set temperature
The water collection tray is full.Turn
off the unit, drain the water from the
water collection tray and restart the
unit.
The air filter is blocked
with dust or animal hair
Exhaust hose is not connected
or is blocked
The unit is low on refrigerant
Temperature setting is too high
The room area is too large
There are heat sources inside
the room
The ground is not level
The air filter is blocked
with dust or animal hair
This sound is caused by
the flow of refrigerant inside
the unit
The windows and doors in the
room are open
Unit does not
cool well
The unit is noisy and
vibrates too much
The unit makes
a gurgling sound

Design and Compliance Notes
14
Design Notice
Energy Rating Information
In order to ensure the optimal performance of our products, the design specifications of the unit and remote
control are subject to change without prior notice.
The Energy Rating for this unit is based on an installation using an un-extended exhaust duct without
adapters A or B (as shown in the Installation section of this manual).
Unit Temperature Range
Cool 17-35°C (62-95°F)
Dry
13-35°C (55-95°F)
Mode Temperature Range

C( 23
Model
Transmission Distance
Lowest Voltage of
CPU Emitting Signal
Rated Voltage
26 ft (8 m)
2.0V
Environment
Technical Specifications
。 。 O O
-5 C 60 F~140 F)
RG09E/BGCE
3.0V(Dry batteries R03/LR03×2)
MODE
LED
CLOCK
C
ON
OFF
SET TEMP.
FANSPEED
AUTO
F
REMOTE CONTROL INSTRUCTIONS
15
~

Features of remote control
1
ON/OFF Button: Push this button to start the air conditioner; push
the button again to stop the air conditioner.
2
MODE Select Button: Each time you push the button, a mode
is selected in a sequence that goes from AUTO, COOL, DRY
and FAN, as the following figure indicates:
AUTO COOL DRY
FAN
1
2
3
4
5
6
7
8
9
10
11
MODE
LED
CLOCK
C
ON
OFF
SETTEMP.
FANSPEED
AUTO
F
3
TEMP/TIME Button : Push the button to increase the
indoor temperature setting or to adjust the TIMER in a clockwise
direction. Push the button to decrease the indoor
REMOTE CONTROL INSTRUCTIONS
16

Features of remote control(continued)
RESET Button: When you press the recessed RESET button,
all current settings are cancelled and the control will return to
its initial settings.
FAN Button: Used to select the Fan Speed in four steps-
AUTO、LOW 、MED (on some models only) or HIGH. Each
time the button is pressed, the fan speed mode is shifted.
temperature setting or to adjust the TIMER in a counter-clockwise
direction.
NOTE: Press and hold and buttons together for 3 seconds
to alternate the temperature display between the C & F scale.
TIMER Button: This button is used to preset the time ON
(start to operate) and the time OFF (turn off the operation).
LOCK Button: When you press the LOCK button, all current
settings are locked in and the remote controller does not accept
any operation except that of the LOCK. Press again to cancel
the LOCK mode.
CANCEL Button:
(a). If the TIMER ON, TIMER ON OFF or TIMER OFF ON
feature has been set, pressing the CANCEL button will override
the TIMER program and turn off the unit as well.
(b). When TIMER OFF has been set, pressing the CANCEL button
will cancel the timer off setting and turn on the unit (when
the unit is off).
(c). If no TIMER feature has been set, pressing the CANCEL button,
will have no effect.
CLOCK Button: Used to set the time.
LED Button: Press this button to clear the digit display in the
air conditioner, press it again to activate it .
SLEEP Button: In SLEEP mode,
pressing this button will activate or deactivate sleep function.
This function allows the unit to maintain the most comfortable
temperature and save energy. This function is available on
COOL or AUTO mode only. For more information, see
“Sleep operation” in “USER’s MANUAL”.
NOTE:
be cancelled if MODE, FAN SPEED or ON/OFF button is
pressed.
While the unit is running under SLEEP mode, it would
REMOTE CONTROL INSTRUCTIONS
17
6
5
7
9
8
10
11
4

CLOCK
C
ON
OFF
SET TEMP.
FAN SPEED
Indicators on remote controller
Transmission Indicator
Temp. display
Time display
Fan speed display
Sleep Display
Mode display
ON/OFF display
This transmission indicator lights up when
remote controller transmits signals to the
indoor unit.
Displays the current operation mode. Including
AUTO( ), COOL( ), DRY( ) , FAN
ONLY ( )and back to AUTO( ).
。
Displays the temperature setting (17 C/62 F
to 30 C/86 F). When you set the operating
mode to FAN ONLY, no temperature setting is
displayed.
Displayed by pressing the ON/OFF button.
Press the ON/OFF button again to remove.
The clock time is indicated only when no
AUTO-ON/OFF timer is set. When AUTO-
TIMER feature is operating, it displays the
AUTO-ON/OFF time. To check the current
time, press the CLOCK button, and the time
will display.
Displays Timer on/off time(0 24 hours)
or clock time.
Displays the selected fan speed, AUTO
and three fan speed levels " " (LOW)
" " (MED) " " (HIGH)
can be indicated. Displays AUTO when the
operating mode is either AUTO or DRY.
Displays by pressing the SLEEP button.
Press the SLEEP button again to remove.
Note:
All displays on the remote control are
shown for illustration purposes only.
AUTO
F
AUTO
AUTO
Lock Display
Displays by pressing the LOCK button.
Press the LOCK button again to remove.
~
Note: Some models have no MED Fan
speed selection.
REMOTE CONTROL INSTRUC
18

Keep the remote controller where its
signals can reach the receiver of the
unit (a distance of 8m is allowed).
When you select the timer operation, the
remote controller automatically transmits
a signal to the indoor unit at the specified
time.
If you keep the remote controller in a
position that hinders proper signal
transmission, a time lag of up to 15
minutes may occur.
Loca tion of the remote contr oller.
.
.
8m
CAUTIONS
The air conditioner will not operate if curtains, doors or other materials
block the signals from the remote controller to the indoor unit.
Prevent any liquid from falling into the remote controller. Do not expose
the remote controller to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the air conditioner may not function properly. Use curtains to
prevent the sunlight from falling on the receiver.
If other electrical appliances react to the remote controller. either move
these appliances or consult your local dealer.
.
.
The remote controller uses two
dry batteries (R03/LR03X2)
(1) Slide the cover of the battery
compartment off according to the
arrow direction, then replace the
old batteries with new ones.
(2) Insert the new batteries making
sure that the batteries' polarity (+/-)
is respected.
(3) Reattach the cover by sliding it
back into position.
After replacing batteries, set the
remote controller clock.
R eplacing ba tteries
.
.
.
Handling the remote controller
Do not recharge batteries or dispose of them in fire.
protect the environment
containers to
REMOTE CONTROL INSTRUCTIONS
This Class B digital apparatus complies with the Canadian ICES-003 standard. CAN ICES-3 (B)
19