ARCTIC WIND 1AW2BF33A User manual

COMPACT REFRIGERATOR
3.3 CU. FT. DOUBLE DOOR
MODEL 1AW2BF33A
OWNER’S MANUAL

19. WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in structure,
clear of obstruction.
20. WARNING: Do not damage the refrigerant circuit.
21. WARNING: Do not use electrical appliances inside the food storage compartments of the
appliance, unless they are of the type recommended by the manufacturer.
1
This appliance is not intended for use by persons (including children) with
reduced physical,sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure their do not play with the appliance
For compression-type appliances which use flammable refrigerants, instructions shall
include information pertaining to the installation, handing, servicing
4
6
22

2
22. WARNING: Do not use electrical appliances inside the food storage compartments of the
appliance, unless they are of the type recommended by the manufacturer.
Appliances which use flammable insulation blowing gases instructions shall
include information regarding disposal of the appliance
Instructions shall contain the substance of the following;
Do not use extension cords or ungrounded (two prong) adapters
This product should not be disposed with other household wastes.
To prevent possible harm to the environment or human health from uncontrolled waste
disposal recycles it responsibly to promote the sustainable reuse of material resources.
To return and collection systems or contact the retailer where the product was purchased.
They can take this product for environmental safe recycling
WARNING! Refrigerators contain refrigerant and gases in the insulation.
Refrigerant and gases must be disposed of professionally as they may cause eye
injuries or ignition Ensure that tubing of the refrigerant circuit is not
damage prior to proper disposal.

prong) adapters.
3
115V/120V, 60Hz power supply.
Do not use extension cords or ungrounded(two

4

5
8. Can Rack
9. Door Gasket

6

7

Tools you will need:
.8mm socket driver
.
Note: Before this step, you should lay the refrigerator
on it’s back in order to gain access to the base, you
should rest it on soft foam packaging or similar
material to avoid damaging the cooling pipes at the
rear of the refrigerator.
.
2. open the screw hole cove and the upper
hinge cover which is at the top right corner of
the refrigerator. upper hinge
cover (right)
1. Stand the refrigerator, open the upper
door and remove the things in the door and
close it.
3.Unscrew the special flange self-tapping
screws which are used for fixing the right
upper hinge part by a 8mm socket driver
or a spanner(please support the upper
door with your hand when doing it ).
right upper hinge part
special flange
selftapping screws
5.Remove upper door and place it on
smooth surface with panel upwards.
6. Loose screws used to fix middle hinge
and remove middle hinge. Then turn middle
hinge by 180. Take washer on axis and put
it on another end. Place it well for use.
7. Remove lower door and place panel
upwards on smooth surface.
8. Change screw hole covers on middle
cover plate from left to right (as shown in
figure below).
Front foot fixed board
Self tapping screws
Adjustable bottom feet part
Lower hinge partΰrightα
4.Remove the right upper hinge part and
screw hole cover ,place them on the
smooth surface.
screw hole cover
.7mm wrench
Caution㧦
To avoid to injury or damage to property,
we recommend someone to assist you
during the door reversal process.
•Ensure the Appliance is unplugged
and empty.
•Following steps are generally
recommended
Changing the doorsfrom right to left.
The side at which the door opens can be
changed from the right side (as supplied) to
the left side, if the installation site requires.
8
phillips screwdrivers
Putty Knife or slotted srewdrivers
Parts you will need ,parts are from the package of manual
door stopper door stop

10. Change lower hinge part to left and front
foot fixed board to right and fix them with
screws. Then install adjustable bottom feet
parts.
Lower hinge part (left)
ower
door and adjust its position to align lower
hole(left) site and lower hinge axis. Then
adjust middle hinge and align the middle
hinge axis to the higher (left) hole site. Then
install the middle hinge.
Stand the refrigerator then
Note: washer may
stick to lower door. Washer
13. Replace and the right upper hinge Install
cover on the left corner, Replace the screw
hole cover on the right corner.
14.Stand and level the appliance.
NOTE:
Before the appliance is powered, We
recommend that you should wait for about
.
2 hours
9
11.Remove the door stop (right) and
door stopper (right) with
,Install the door stopper(left) and
door stop (left) which are from the package
of user's manual
move l
Phillips screwdrivers

855-663-9463 |[e-mail] |www.arcticwindac.com
5401 Dansher Road
Countryside, IL 60525
Printed in China |0522_M977