This guide is for quick installing and connecting the CI-403 / CI-333 Network Camera. For more
details, please refer to the User’s Manual.
No. Connector Pin Definition
1
1
2
3
4
5
6
7
8
9
2
3
4
5
6
7
8
Please follow the instructions below for cable connections.
Power Connection
Please use a DC12V / AC24V power adaptor and plug it to the power connector of the camera
and the power outlet.
Alternatively, users can use an Ethernet cable and connect it to the RJ-45 connector of the
camera and a Power Sourcing Equipment (PSE) switch.
Ethernet Cable Connection
Connect one end of the Ethernet cable to the RJ-45 connector of the camera, and plug the
other end of the cable to the network switch or PC.
A client program will be automatically installed to the PC when connecting to the camera.
Before logging in to the camera, ensure downloading the ActiveX control is allowed by either
changing the ActiveX controls and plug-ins or setting Internet’s security level to default.
NOTE : It is not recommended to record with the microSD card for 24/7 continuously, as
it may not be able to support long term continuous data read/write. Please
contact the manufacturer of the microSD card for information regarding the
reliability and the life expectancy.
NOTE : If PoE is used, make sure PSE is in use in the network.
NOTE : In some cases, Ethernet crossover cable might be needed when connecting the
camera directly to the PC.
Alarm I/O
Network LEDs
PoE Network (RJ-45)
microSD Card Slot
Audio I/O (Line In/Out)
Default Button
Power (DC12V / AC24V) Power connection
Power LED
Alarm In 2 + Alarm connection
* Do NOT connect external
power supply to the alarm
I/O connector of the IP
camera.
RS-485 connection
Ground connection
For analog video output
Alarm In 1 +
Alarm In –
Alarm Out –
Alarm Out +
D −
−
−
−
−
−
−
−
+
D +
GND
BNC
DC12V + AC24V 1
DC12V − AC24V 2
For network connection and activity indication
Two-way audio transmission
Power LED lights up when the camera is powered on.
Press the button with a proper tool for at least 20
seconds to restore the system.
For network and PoE connections
Insert the microSD card into the card slot to store
videos and snapshots. Do not remove the microSD
card when the camera is powered on.
Remarks
CI-403 / CI-333 Network Camera Quick Guide
8
Camera’s Connectors
Camera Cabling
Before Login to the Camera
NOTE : Check the status of both power and network activity indicator LEDs. If either LED
is unlit, please check the corresponding connection.
Green Power LED lights up when the camera is powered up.
Orange Network LED (1) flashes when data is being transmitted over network,
(2) lights up for good network connection.
NOTE : The ITE is to be connected only to PoE networks without routing to the outside
plant or equivalent description.
Step 1 : Start the Internet Explorer (IE).
Step 2 : Select <Tools> from the main menu
of the browser. Then click on
<Internet Options>.
Step 3 : Click on the <Security> tab and
select <Internet>, and click on
<Custom level> to change ActiveX
settings.
Step 4 : Set “ActiveX controls and plug-ins”
items to <Prompt> or <Enable>.
ActiveX Controls and Plug-ins Settings
Step 1 : Start the Internet Explorer (IE).
Step 2 : Select <Tools> from the main menu
of the browser. Then click on
<Internet Options>.
Step 3 : Click on the <Security> tab and
select <Internet>.
Step 4 : Down the page, click <Default Level>
and click on <OK> to confirm the
setting. Close the browser window,
and open a new one later for
accessing the IP camera.
Internet Security Level
1
PoE NETWORK
LINE IN
ALARM IN
ALARM OUT
RS-485
GND
BNC
LINE OUT
Micro
SD
Default
DC12V/AC24V
PWR
+
-
I
2+
I
1+
I
-
O
-
O
+
D
+
D
-
7
2
5
6
3
4
1
2
3
4
5
6
7
8
9
