Arena Luci Design THOR LED 60x60 Elite Series User manual

THORLED
60x60Elite
User'smanual
Ultraslim60x60LEDpanel
This unit should only be used for purpose for
which it has been intended and should be
installed using the instructions which are
provided. Arena Luci cannot be held liable for
damagestoperson,animalsorobjectsasaresult
ofimproper,unreasonableandwrongusage.
This instruction manual contains important
information about the installation and use of the
luminaire. Please read and follow these
instructionscarefully.
Thesecurityofthisdeviceisguaranteedonlywith
the proper use of the following instructions,
thereforetheymustbekeptcarefully.
Never install the device in locations easily
accessiblebypeoplewhoignoretheexistenceof
thisuser'smanualandsafetyinstructions.
For the wiring please refer to enclosed wiring
diagrams. If in the diagrams indicated there
shouldnotbethatofyourapplication,contactthe
technicaloffice.
Disconnecttheunitfromanypowersupplybefore
attempting any operation in contact or inside the
unit,andwhennotinuse.
Itisessentialthateachdeviceiscorrectlyearthed
and that electrical installation conforms to all
relevant standards. Never supply the unit without
theearthlink.
Prior to connect the unit to the mains supply,
check the output voltage fits the technical
requirementsonthelabel.
Never let the power cord come into contact with
othercables.
Nevertouch theelectrical contacts, either directly
with your fingers, or indirectly by means of sharp
ormetalobjects.
Makesurethatcablescannotcausetriphazard.
Donotattempttodismantleandmodifytheunit.
Due to the high technological level of this unit,
anyservicemaintenance should beperformedby
specialised operators. Please contact yourArena
Lucidealerforanyoperation.
Alwaysensurethatthestructuretowhichyouare
attachingtheunitissecureandisabletosupport
theweightofeachunit.
Do not allow contact with water or any other
fluids,ormetallicobjects(IP54/IP40).
Avoidinstallingtheunitclosetoheatsources.
Neverleanthepowercordonhotunitsurfaces.
Allowed to be mounted directly on inflammable
surfaces.
Installtheunitwhereitcanbeeasilyaerated.
Do not install the luminaire on deformed or
damagedceilings.
Thelightingapparatusmustbeusedonlywithits
protectiveplasticshield.
Contact your Arena Luci dealer if the protective
shieldisvisiblydamagedtothe point at which its
effectiveness is diminished, for example by
becomingcrackedordeeplyscratched.
LEDmoduleisnotreplaceable.
Do not use any solvent based cleaning agents.
Useonlyasoft,dryantistaticcloth.
The installation of LED modules (including power
supplies) should be done according to current
technical rules and regulations. The installation
shouldbeperformedonlybyaqualifiedoperator.
Avoid contact with either corrosive agents or
humidity and moisture on delicate elements:
damages from corrosion are not refunded as
componentdefects.
WARNINGS
Please note that as part of Arena Luci's ongoing commitment to continuous product development,
specifications are subject to change in the course of product improvement without notice.Arena Luci is not
responsiblefordamagesresultingfromimproperordifferentusethanexpected.
PNL2140iWW
PNL2140iNW

2/4
PNL2140i
BEFORESTARTING
Remove the product from the shipping carton,
checking that all the components supplied are
presentin the box.Refer tothe following packing
list to check which components must be present
in the packaging. If any component is missing or
damaged, contact your Arena Luci dealer
immediately.
n°1LEDpanelThor60x60Elite
n°1Electronicdriver
Before starting the installation of your product
make sure that there are no evident damages
caused by transportation. In the event that the
luminaireisdamaged,donotplugitinanddonot
attempt to use it until you contacted your Arena
Lucidealerforassistance.
INSTALLATIONANDPOWERSUPPLY
Thepanelcanbeinstalledinafalseceiling,ona
concrete ceiling or suspended. Depending on the
typeofinstallationitisnecessarytofindasuitable
housing for the power supply or it is possible to
placethepowersupplyinthemiddleoftheupper
faceofthepanel.
Alwaysmakesurethatthestructureyouarefixing
the panel is safe and able to bear the weight of
3.1kgofeachappliance,possibly including power
supply.
Remove the mains voltage from the system
before performing any of the installations listed
below.
Drag the derivations from the 230V power line to
the position where the electronic driver will be
installed. Keep in mind that the output of the
powersupplythatisconnectedtothepanelhasa
cable with a length of about 15cm, so there is a
discrete freedom in choosing the position of the
powersupply.
Connectthepowersupplytothemains,usingthe
voltage and frequency indicated on the label and
observing the indicated polarity LNE (colors
brown=L,blue=N,yellow/green=E).Makesure
that no conductors have uncovered copper
pieces.
Itisadvisablethatthepowersupplyisconnected
to the mains via its own switch, so that it can be
switchedonandoffindividually.
Theterminalblockcanacceptconductorsofcross
section between 0.5 and 1.5 mm2; for fixing
remove approximately 56 mm of insulation from
thewires.
It is essential that the electrical installation
complieswithallcurrentgoodtechnicalandsafety
standards.
Falseceilinginstallation
Thor panel has been specially designed to be
housed on a normal frame for squared ceilings.
After having housed the power supply inside the
false ceiling, take the cable with the plug
connectorofthepowersupplyunitoutofthefalse
ceiling and connect it firmly to the corresponding
socket on the panel power cable (Fig. 01).
Positionthepanelonthesupportframe.
Ifthefalseceilingisoftheplasterboardtype,itis
necessary to use the accessory for fixing to a
falseceiling(APL1200).
Make a square hole of the appropriate size for
housing the accessory, as indicated in the
instructions attached to the product, and attach it
totheplasterboard.Laythedriverinsidethefalse

3/4
USER'SMANUAL
ceiling and pull the cable with the plug connector
outfromtheholeinthefalseceilingandconnectit
firmly to the corresponding socket on the panel
power cable (Fig. 01). Insert the panel inside the
casingandfixit.
Ceilinginstallation
Anaccessory (codeAPL1100) isavailable forthe
installation of the panel on a concrete ceiling, in
cases where there is no false ceiling. This is a
framethatmustbefixeddirectlytotheceilingand
inwhichthepanelissubsequentlyinserted.
Beforefixingtheframe,makesurethatthepower
supplylinecanexitinsidetheframeitself.
Drill four holes on the ceiling, arranged at the
corners of a rectangle to fix the frame, get the
interaxis between the holes measuring the frame
and mark them with a pencil on the ceiling. Pass
the power cable through the back of the frame
and then screw the back to the ceiling using
expansion plugs of the type suitable for the type
ofceilingandtheloadtosupporttheweightofthe
frameandpanel.
Once the back of the frame is firmly fixed to the
ceiling, connect the plug connector of the power
supply unit to the corresponding socket on the
panelpowercable(Fig.01).
FinalizetheinstallationbyinsertingtheLEDpanel
on the two guides of the frame pushing it all the
way down, put the power supply in the middle of
the upper face of the panel and finally close the
framebyscrewingtheclosingcover.
Suspendedinstallation
If you wish to install the panel in suspension, an
accessory is available that contains everything
necessary for the purpose (APNL1236S). Follow
theinstructionsattachedtotheproducttoidentify
thefixingpointsonboththepanelandtheceiling
andhowtoadjustthesuspensionheight.
Thecableforconnectiontothemainssupplymust
come out of the ceiling. Firmly connect the plug
connector of the power supply unit to the
corresponding socket on the panel power cable
(Fig.01).
Fig.01ConnectingtheLEDpanel

4/4
PNL2140i
ArenaLucisrlviaSvizzera12/1446042CastelGoffredo(MN),Italy
Tel.+390376782411Fax+390376780973
www.arenaluci.com[email protected]
WARRANTYCONDITIONS
The unit is guaranteed for 24 months from the
date of purchase against defects in workmanship
ormaterialsthatcomposeit.
This warranty does faults due to incorrect or
improperuseofthedevice.
The warranty is immediately void if the unit has
been tampered with or opened by unauthorized
personnel.
The warranty provides, at the discretion ofArena
Luci,repairorreplacementoffaultyequipment.
The serial number and model of the device are
required to obtain information or assistance from
the dealer. We invite you to transcribe them in
time: for any request of information or services,
thiswillresultinaquickandeffectiveoperation.
CERULES
The device meets the essential requirements of
the Directives LVD 2014/35/UE, EMC
2014/30/UE, RAEE 2012/19/UE, RoHS
2011/65/UE, Ecodesign 2009/125/CE reg. (UE)
1194/2012, Energy label 2010/30/UE reg. (UE)
874/2012 reg. (UE) 518/2014, GPSD
2001/95/CE.
Warnings
DisposalofOldElectrical & Electronic Equipment
(applicable in the European Union and other
European countries with separate collection
systems).
The product shall not be treated as
householdwastebutmustbehandedoverto
the applicable collection point for the
recycling of electrical and electronic
equipment. By ensuring this product is correctly
disposed, you will help prevent potential negative
consequences for the environment and human
health, which could otherwise be caused by
inappropriate waste handling. The recycling of
materialswillhelptoconservenaturalresources.For
more detailed information about recycling of this
product, please contact your city office, your
householdwastedisposalserviceoryoursupplier.
Powersupply
Powerconsumption
Sorce
ColorTemperature
Luminousflux
Beamaperture
Socket
Drillinghole
Material
Color
Weight
Dimensions
Insulationclass
Protection
Ambienttemperature
Suitabletobefittedonnormallyinflammablesurfaces
Appliedstandards
220240VAC,50/60Hz
40W
smdLED
3000K(WW)4000K(NW)
3878lm(WW)3955lm(NW)
120°
Terminalblock
600x600mm(APL1200)
Aluminium+PC
Whiteframe
Body:3.1kgDriver:105g
Body:595x595x11mmDriver:147x44x30mm
I
IP54(front)IP40(rear)
25°C...+45°C
TECHNICALSPECIFICATIONS
PNL2140iENR0|10/2018
This manual suits for next models
2