Ares 1KVAS User manual

USER MANUAL
(ONLINE UPS)
Thanks for using our products
Please strictly obey all the instructions in this manual and pay attention to all the warning and operation
information. It is not advisable to install or operate the machine before reading this manual.
1. Safety instructions
●The power output voltage may still have 220V or 120V even not connect to the mains power.
●For the battery cable or power cord replacement, please contact our service station or dealer to purchase, in
order to avoid fire caused by inadequate capacity or heat ignition.
●Do not place the battery or battery pack in the fire, which will injure due to explosion.
●Please do not open the UPS case as you will, there is risk of electric shock
●Do not touch the battery connection terminals. Battery loop and input voltage loop is without isolation, which
may cause high voltage risk between the battery terminal and ground.
●Do not connect to the equipment like hair dryer or electric heater, to ensure the safety for the UPS
Attention:
UPS has high voltage inside, for personal safety, please do not repair by yourself. If any questions, please
contact local service center or dealer.
2. Installation instructions
2.1 Unpacking inspection
●Open the UPS package, please check the enclosed accessories including a user manual, communication
cable, CD-ROM. The long-back model also includes the cable for connection to battery bank.
●Check the UPS if any damage in transport. If find damaged or parts missing, do not power on, please turn to
the carrier and dealer.
●To determine whether this UPS is the model you want to buy. Check the model name showed both on the
front panel and rear panel of UPS to confirm.
Model
Type
Model
Type
1KVAS
1KVA Standard model
1KVAH
1KVA Long backup model
1.5 KVAS
1.5 KVA Standard model
1.5 KVAH
1.5 KVA Long backup model
2KVAS
2KVA Standard model
2KVAH
2KVA Long backup model
3KVAS
3KVA Standard model
3KVAH
3KVA Long backup model
6KVAS
6KVA Standard model
6KVAH
6KVA Long backup model
10KVAS
10KVA Standard model
10KVAH
10KVA Long backup model
Note:
Please save the packaging box and packaging materials for future transport use. As heavy product, please
transit the UPS with care.

1
2.2 Attention items of installation
●The UPS installation environment must be with good ventilation, away from water, flammable gases and
corrosive entities.
●Do not lie down the UPS against the wall so that front and side panel air intake hole, rear panel air outtake
hole will be unobstructed.
●The peripheral environment temperature around the UPS should be within 0 ℃~ 40 ℃.
●If dismantling the machine at low temperatures, there may be condensation droplets, users can not install
or operate it before UPS completely got dry both inside and outside, otherwise there will be danger of
electric shock.
● Place the UPS near the mains socket to cut offAC mains without any delay at any emergent case.
Attention:
●Make sure the load behind the UPS is off when users connect the load to UPS, and then turn on the load
one by one later.
●Please connect the UPS with the socket which is over-current protected. Do not connect the UPS with the
socket which rated current is less than the Maximum input current of the UPS.
●All the power socket should be configured with earthling device for safety.
●UPS could be electrified or powered no matter the input power cable is tied or not, even when the UPS is off.
The only way to cut off the output is switching off the UPS and disconnecting the mains power supply.
●For all standard type UPS, it is advised to charge the battery over 8 hours before used. Once the AC mains
power energizes the UPS, it will automatically charge the battery. Without prior charging, UPS output
remains as usual but with shorter back-up time than normal.
●When connected to motor, display equipment, laser printer etc, UPS power selection should be based on
the startup power of the load which is usually twice as rated power.
2.3 UPS rear panel view
Note: following diagrams take the type of 0.9PF for example, the type of 0.8PF is similar.
2.3.1 The type of 220V (output could be 208V, 210V, 220V, 230V, 240V)
RS232
EPO
USB
TEL/MODEM/FAX
IN OUT
OUTPUT
RESET
FUSE 250VAC
INPUT
-+ 36VDC 30A
EXT.BATTERY
2
1
3
5
6
48
7
10
9
TEL/MODEM/FAX
OUT
IN
USB
EPO
OUTPUT SOCKET
RS232
-
+- +72VDC 30A
EXT.BATTERY
-
+- +
RESET
FUSE 250VAC
INPUT
2
1
6
8
10
7
4
5
9
TEL/MODEM/FAX
OUT
IN
USB
EPO
OUTPUT SOCKET
RS232
-
+- +96VDC 30A
EXT.BATTERY
RESET
FUSE 250VAC
INPUT
-+ -+
2
1
6
8
10
7
4
5
9
3
a. 0.9PF 1KVA rear panel b. 0.9PF 1.5KVA&2KVA rear panel c. 0.9PF 3KVA rear panel

2
计算机接口
NL L N
++ -- 11
12
6
7
8
3
2
NL L N
6
2
12
11
3
8
7
INPUT BREAKER
80A 250VAC
ON
OFF
TEL/MODEM/FAX
INTELLIGENT SLOT
-
+- +192VDC
EXT.BATTERY
DO NOT OPEN EXCEPT
QUALIFIED TECHNICIAN
RS232
USB
EPO
N L L2 N2
INPUT OUTPUT
WARNING
HIGH LEAKAGE CURRENT
EARTH CONNECTION ESSENTIAL
BEFORE CONNECTING SUPPLY
～ ～
L1 N1
NLL2 N2
L1 N1
912
11
8
7
6
5
4
3
2
d. 6KVA &10KVA Long back up e. 6KVA & 10KVA Standard type f . 0.8/0.9PF 6/10KVA with ISO
2.3.2 The type of 120V (output could be 100V, 110V, 115V, 120V, 127V)
RESET
-
+
24VDC 40A
EXT.BATTERY
INTELLIGENTSLOT
RS232
INPUT
OUTPUT SOCKET
TEL/MODEM/FAX
IN OUT
USB
EPO
FUSE 125VAC,15A
R
E
S
E
T
R
E
S
E
T
T
O
1
2
4
5
6
8
3
7
10
9
RESET
FUSE 125VAC,25A
INPUT
OUTPUT SOCKET
RS232
USB
EPO
TEL/MODEM/FAX
OUTIN
OUTPUT
L N GND
R
E
S
E
T
R
E
S
E
T
T
O
-+
48VDC 40A
EXT.BATTERY
INTELLIGENTSLOT
1
2
5
6
7
4
9
8
10
11
RESET
FUSE 125VAC,35A
INPUT
OUTPUT SOCKET
TEL/MODEM/FAX
OUT
IN
RS232
USB
EPO
INTELLIGENTSLOT
OUTPUT
L N GND
R
E
S
E
T
R
E
S
E
T
T
O
-
+
72VDC 40A
EXT.BATTERY
5
6
4
1
2
3
7
9
8
10
11
a. 0.9PF 1KVA rear panel b. 0.9PF 2KVA rear panel c. 0.9PF 3KVA rear panel
⑴Input Power Terminals；⑵Over Current Protector；⑶Fan；⑷USB；
⑸Emergency Power Off；⑹RS232 Communication Interface；⑺Intelligent Slot；
⑻Surge Protection for Network/Fax/Modem；⑼Battery Slot；⑽Output Socket；
⑾Terminal Block；⑿Manual bypass switch cover.
2.4 UPS output connection
Output connection of 1~10KVA type is configured with sockets or terminal blocks, users can plug the load
cable into the UPS socket to energize the load as below. Make sure the mains wire and breakers in the
building are enough for the rated capacity of UPS to avoid the hazards of electric shock or fire.
Note: To the type of 6-10KVA, do not use the wall receptacle as the input power source for the UPS, which
rated current is less than the UPS’s maximum input current. Otherwise the receptacle may be burned and
destroyed.
(1) In general, users can easily connect the load cable into the socket or terminal block of the UPS as
following pictures.

3
LOAD Input Output
Ground
NL L N
+-
Battery
Protector
Over Current
R
E
S
E
T
R
E
S
E
T
T
O
+-
Input
Output
(2) To the type of 6~10KVAwitch contains isolation transformer, there are more methods of output connection.
Before installing, prepare wires for terminal block of the UPS based on the following table.
Model
Wiring spec(AWG)
Input
Output
Battery
Non-isolated Neutral
Ground
6KVAS
6mm2
6mm2
6mm2
6mm2
6mm2
6KVAH
6mm2
6mm2
6mm2
6mm2
6mm2
10KVAS
10mm2
10mm2
10mm2
10mm2
10mm2
10KVAH
10mm2
10mm2
10mm2
10mm2
10mm2
Note: ①The cable for 6KVAS/6KVAS should withstand over 40A current. It is recommended to use 10AWG
or thicker wire for safety and efficiency.
②The cable for 10KVAS/10KVAS should withstand over 63Acurrent. It is recommended to use 8AWG
or thicker wire for safety and efficiency.
③The selections for color of wires should be followed by the local electrical laws and regulations.
Installation:
A. Remove the terminal block cover on the rear panel of UPS. Then connect the wires according to the
following terminal block diagrams: Connect the earth wire first when making wire connection. Disconnect
the earth wire last when making wire disconnection!)
OFF
-
+- +192VDC
EXT.BATTERY
N L L2 N2
INPUT OUTPUT
～ ～
L1 N1
N1
Ground
Input
Battery
Output1
Output2
Protector
Over Current
L2 L2
L1 L1 N1

4
Note: ①Make sure the wires are connected tightly with the terminals.
②There are two output terminals to meet customers’diverse requirements for serial or parallel
connection. We will introduce the methods of connection later.
③Please install the output breaker between the output terminal and the load, and the breaker should
be qualified with leakage current protective function if necessary.
B. Insert the EPO plug into the EPO slot on the real panel.
C. Put the terminal block cover back to the rear panel of the UPS.
Warning: (only for long-run model)
◇Make sure a DC breaker or other protection device between UPS and external battery pack is installed. if
not, Please install it carefully. Switch off the battery breaker before installation.
Note: Set the battery pack breaker in “OFF”position and then install the battery pack.
◇Pay highly attention to the rated battery voltage marked on the rear panel. if you want to change the
numbers of the battery pack, please make sure you modify the setting simultaneously. The connection with
wrong battery voltage may cause permanent damage of the UPS. Make sure the voltage of the battery
pack is correct.
◇Pay highly attention to the polarity marking on external battery terminal block, and make sure the correct
battery polarity connected. Wrong connection may cause permanent damage of the UPS.
◇Make sure the protective earth ground wiring is correct. The wire current spec, color, position, connection
and conductance should be checked carefully.
◇Make sure the utility input＆output wiring is correct. The wire current spec, color, position, connection and
conductance should be checked carefully. Make sure the L/N site is correct, not reverse or short-circuited.
Output Configuration
★Option 1:
GND L1 N1 L2 N2
To Load2
To Load1
L2 L1
There are 2 sets of low-voltage output (100V/110V/115V/120V) with L1-N1 and L2-N2. Each of them is able
to provide 50% of UPS rating power. Connect one load to L1-N1 and the other load to L2-N2.
★Option 2:
GND L1 N1 L2 N2
To Load
L2 L1
After connecting L1&L2 and N1&N2, it becomes one low-voltage output (100V/110V/115V/120V) at L1-N1 for
100% of UPS rating power. Connect load to L1-N1 or L2-N2.

5
★Option3:
GND L1 N1 L2 N2
To Load
L2 L1
After connecting N1 and L2, it becomes one low-voltage output (208V/220V/230V/240V) at L1-N2 for 100%
of UPS rating power. Connect load to L2-N1
★Option4:
GND L1 N1 L2 N2
To Load 1
To Load 2
To Load 3
L2 L1
After connecting N1＆L2, it becomes three outputs, one high-voltage((208v/220v/230v/240V) at L1-N2 two
low-voltage outputs (100v/110v/115v/120V) at L1-N1 and L2-N2. However, there is a limit for current rating at
L1-N1 and L2-N2: 25A is for 6KVA model and 42A is for 10KVA model. You must connect the load under the
limitation. Please read Note first before installation.
Connect low-voltage load to L1-N1 and L2-N2, and connect high-voltage load to L1-N2.
Note: ①if any load current in L1-N1 or L2-N2 is higher than 25A in 6KVA model and 42A in 10KVA model.
The UPS will still operate normally without overload warning because the total load is under the
specification. However, the isolation transformer will be damaged with overheat due to high current.
Hence, the installation must be done with technician and make sure that the load current does not
exceed this limitation.
②When connecting to low-voltage and high –voltage at the same time like option 4, it will cause the
L1-N1＆L2-N2 with low-voltage loads in Non-Isolated status, we recommend that you may only use
two low-voltage at L1-N1 or L2-N2 like option 1, and also make sure that the total current in L1-N1 or
L2-N2 does not exceed the value on Note 1.
2.5 External battery connection procedure for long back up type
●For different UPS type, users are instructed to configure different battery voltage as below sheet. More or
less units are forbidden, or else something abnormal or faulty will appear.
Type
Battery Quantity
(unit)
Battery Voltage
(volt)

6
1KVA
2/3
24/36
1.5KVA
4
48
2KVA
4/6
48/72
3KVA
6/8
72/96
6KVA
14/16
168/192
10KVA
14/16
168/192
●One end of battery cable is for UPS terminals while the other end with triple cables is for battery terminals.
Correct installation procedure is highly vital or else probable electric shock will arise. Users are strictly
required to follow the below procedure.
●Connect battery in correct way and make sure the total battery voltage is available for UPS.
●Correctly connect the long battery cable to battery terminals first, red wire is to positive plate while black is to
negative. If users connect the UPS first, electric shock or other danger could not be avoided.
●Before connecting load after UPS, users should supply main power to UPS and energize it.
●Connect long battery cable to UPS terminals with correct poles link (red is for “+”, black is for“-”), UPS will
start the charging work automatically.
RED
BLACK
-
+
-
+-
+
-
+
-
+-
+
2.6 Installation
●UPS installation work should comply with local electrical standard and only can be done by professional
technician. 1KVA~3KVA units could use wall socket as input power connection.
●For all type UPS, it is advised to charge the battery over 8 hours before the first use. Once the AC mains
power energizes the UPS, it will charge the battery automatically. Without prior charging, UPS output
remains as usual but with shorter back up time than normal.
3. Panel function and operation
The operation is simple, operators only need to read the manual and follow the operation instructions listed in
this manual without any special training.
3.1 Keys function

7
※ON KEY ( + )
Press and hold the two keys for more than half a second to turn on the UPS.
※OFF KEY ( + )
Press and hold the two keys for more than half a second to turn off the UPS.
※TEST/MUTE KEY ( + )
Press and hold the two keys for more than 1 second in mains mode or economical mode: UPS runs the
self-test function.
Press and hold the two keys for more than 1 second in battery mode: UPS runs the mute function.
※INQUIRING KEY ( , )
Non-function setting mode:
Press and hold or for more than half a second (less than 2 seconds): display the items orderly.
Press and hold for more than 2 seconds: Circularly and orderly display the items every 2 seconds,
when press and hold the key for some time again, it will turn to output status.
Function setting mode:
Press and hold the key for more than half a second (less than 2 seconds): Select the set option.
※FUNCTION SETTING KEY
Non-function setting mode:
Press and hold the key for more than 2 seconds: Function setting interface.
Function setting mode:
Press and hold the key for more than half a second (less than 2 seconds): Enter the function setting option.
Press and hold the key for more than 2 seconds: exit from this function setting interface.
3.2 LED Function
From left to right is inverter LED, battery LED, bypass LED and warning LED.
Warning red LED is on: UPS fault. For example: Overload beyond the allowed time, inverter fault, BUS fault,
over temperature fault etc.

8
Bypass yellow LED is on: UPS is alarming. For example: Bypass mode supply power and etc.
Battery yellow LED is on: UPS is alarming. For example: Battery mode supply power and etc.
Inverter green LED is on: UPS is normally powered by mains or ECO mode or battery mode.
PS: LED display detail in different mode is listed in 5 items.
3.3 LCD display function
LCD displays as following figure.
※Icon display area:
A. The top diagram is for load and battery capacity indication, each grid of which represents 25%. When UPS
is over load , the load light will blink the same as the battery light blink when the capacity of battery get low
or battery disconnected.
B. The fan icon is for fan working indication; when fan normally runs, the icon will display rotation; if the fan is
not connected or faulty, the icon blinks;
C. Press the mute button under the battery mode, buzzer icon will blink; it will disappear in other cases.
D. Fault icon will be on when UPS is in fault mode, otherwise it will not.
※Digital display area:
A. Under none setting mode, it will display UPS output information when UPS normally runs inAC
mode; other information like input, battery, load and temperature will be showed after pressing the inquiring
key; Fault code will be told in fault mode.
B. Under setting mode, user could adjust different output voltage as well as activate ECO and BYPASS mode
by operating function setting key and inquiring keys.
※Mode display area:
A. This area will display the power capacity of the machine after starting the UPS within 20 seconds.
B. After over 20 seconds, this area will display the working mode of the machine. Such as STDBY(standby
Mode), BYPASS(Bypass Mode), LINE(AC Mode), BAT(Battery Mode), BATT(Battery Self Test Mode ),
ECO(economic mode), SHUTDN(shutdown mode).
3.4 Turn On/Off operation
3.4.1 Turn On operation
Digital display area
Working mode
display area
Icon display area

9
i. Turn on the UPS on line mode
①Once mains power is plugged in, the UPS will charge the battery, at the moment, LCD shows that the output
voltage is 0, which means UPS has no output as default condition. If it is expected to have output of bypass,
you can set the BPS “ON” by LCD setting menu.
②Press and hold the ON key for more than half a second to start the UPS, then it will start the inverter.
③Once started, the UPS will perform a self-test function, and LED will light and go off circularly and orderly.
When self-test finishes, it will come to online mode, the corresponding LED lights, UPS is working in line
mode.
ii. Turn on the UPS by DC without mains power
①When main power is disconnected, press and hold the ON key for more than half a second to start UPS.
②The operation of UPS in the process of start is almost the same as that when mains power is on.After the
self-test finishes, the corresponding LED lights and UPS are working in battery mode.
3.4.2 Turn Off operation
i. Turn off the UPS in line mode
①Press and hold the OFF key for more than half a second to turn off the UPS and inverter.
②After UPS shutting down, LED goes out and there is no output. If output is needed, you can set BPS “ON”
on LCD setting menu.
ii. Turn off the UPS in DC mode without mains power
①Press and hold the OFF key for more than half a second to turn off the UPS.
②When turning off the UPS, it will do self-test first. LED lights go out circularly and orderly until there is no
display on the panel.
3.5 UPS self-test/mute test operation
①When UPS is in LINE Mode, press and hold the self-test/mute key for more than 1 second, LED light will go
off circularly and orderly. UPS comes to self-test mode and tests its status. It will exit automatically after
finishing test.
②When UPS is in BAT Mode, press and hold the self-test/mute key for more than 1 second, the buzzer stops
beeping. If you press and hold the self-test/mute key for one more second, it will restart to beep again.
3.6 Panel function setting
UPS has setting function. It can run the setting in any mode.After setting, it will become effective at once
when meets some standards. The set information can be saved only when the battery connected and
normally turning off the UPS.
3.6.1 ECO mode setting
①Enter the setting interface. Press and hold the function setting key for more than 2 seconds, then come
to setting interface, the letters “ECO” will flash;
②Enter the ECO setting interface. Press and hold the function setting key for more than half a
second(less than 2 seconds), then come to setting interface of ECO, at this time, the letters “ECO” will light