argon audio FENRIS User manual

w w w . a r g o n a u d i o . c o m
FENRIS active quick start
We care about the Environment
By refraining from inserting a full printed manual with our Argon Audio
products we save more than 20 tons of paper each year. You can find a full
User Manual in PDF format for this product on; www.argonaudio.com
See back side of this insert for Quick start guide
Safety
Safety Instructions
Unplug this product from the wall outlet before cleaning. Do not use this
product near water or moisture. Do not spill liquids on the product. Clean only
with a dry cloth.
•Place the unit on a solid surface.
•Do not put it in a closed bookcase or a cabinet that may keep air from
flowing through its ventilation openings.
•Do not install near any heat sources, such as radiators, heat registers,
stoves or other appliances that produce heat.
•Protect the power cord from being walked on or pinched, particularly at
plugs and the point where they exit from the product.
•During Lightning storms, unplug the product from the power source or
if unused for long periods of time. This will prevent lightning and
power-line surge damage to the product.
•Do not attempt to service this product yourself. Opening or removing
covers may expose you to dangerous voltages or other hazards. Please
contact the manufacturer to be referred to an authorized service center
near you.
•Do not overload wall outlets, extension cords, or integral power circuits
as this can result in a risk of fire or electric shock.
•Never push any object through the product openings, as this can result
in fire, electric shock or damage.
•Use proper power sources. Plug the product into a proper power
source, as described in the operating instructions or as marked on the
product.
If there is a Lightning flash with an arrow head
on the product, it’s intended to alert the User
of the presence of un-insulated “dangerous
voltage” within the product, that might be of
sufficient magnitude to constitute a risk of
electric shock to persons.
If there is an Exclamation point on the
product, it’s intended to alert the User that
there is important operating and maintenance
(servicing) information in the User manual.
If there is a double rectangular symbol on the
product, it means that the product is double
insulated. Earth connection is not required.

w w w . a r g o n a u d i o . c o m
FENRIS active quick start
Quick start
1. Connect the speakers using the included speaker cable.
2. Connect the power cord into an electric outlet and into the back
of the left speaker (which has the amplifier). The LED light on
the loudspeaker will turn on.
3. To pair your Bluetooth device, turn on the speakers and press
and hold ‘BT’on your remote for about 3 seconds, until the LED
starts blinking. Your speakers are now in pairing mode. Activate
Bluetooth on your playback device and scan for devices. Your
speaker will show up as “Argon Audio FENRIS”. Press “pair” and
you’re connected. The LED light on the speaker will change to
solid blue. You’re now ready to start listening to music!
4. Besides Bluetooth, your FENRIS speakers have four more inputs:
TV ARC, D1, AUX and Phono. FENRIS will automatically switch
between the inputs, but you can also use the included remote
control to select your wished input.
5. When using the TV ARC input, you might need to set the digital
sound output on your TV to PCM. Consult your TV manual to see
how.
6. When connecting a turntable to the Phono input on the FENRIS
speaker, remember to also connect the ground wire from the
turntable to the metal GND screw (if applicable).
7. If you have an active subwoofer, connect it to the FENRIS
speaker’s Pre-out, using an RCA cable and then connect the
cable to your subwoofer.
8. We recommend a running-in time of your FENRIS speakers of
approximately 15-20 hours at normal listening level before you
decide on the final positioning of the speakers.
Basic operating
1. When the FENRIS speakers receive input from any connected
source (except Phono), they will automatically power on (if
powered off) and switch to the right input. This is called Auto
Power Up. Note: this will not happen if the speakers are already
powered on and playing from another source.
2. You can disable Auto Power Up (APU) if needed: simply press
and hold the power button on remote control for 5 seconds
while the speakers are on. The speakers will now power off
with APU disabled. This will also disable automatic power off,
meaning you need to turn off your speakers manually.
3. To enable APU again, simply press and hold the power button
for 5 seconds again when the speaker is powered off.
4. You can always press and hold the ‘BT’button to reset all
Bluetooth connections. Please note that Bluetooth pairing is only
available when the Bluetooth-input is selected.
5. To enable dimming of the LED on the front of the speaker,
power on the speaker and hold the D1 button on the remote for
5 seconds. The LED will now turn off after 5 seconds after
switching inputs. To disable again, press and hold D1 for 5
seconds again.