THE BOX
QR code
Part number
Product name
UNBOXING
• When unboxing the output module you will find the unit and its lid.
• This comes with pre-formed mounting holes to drill out and mount the backbox.
• Securing screws are supplied for the lid.
• A resistor pack is supplied for the monitored load connection (10KΩR ).
For more information, please refer to the complete product manual.
IMPORTANT TO CONSIDER
When mounting a wireless device a comprehensive radio survey
should have been carried out to establish the location that provides
the best coverage and optimum reach. Taking into consideration the building
structure and materials, the survey identifies the wireless infrastructure
required and product locations for optimum performance, identifying
any factor that could prevent radio integrity.
Avoid fixing or mounting the unit close to the following:
• Equipment that utilises large electrical currents
• Large metal objects or structures
• Fluorescent lighting fittings
• Metal ceiling structures
• IT cabling.
Keep 2 meters minimum spacing between other wireless equipment
in the area to avoid signal interference.
EN54 approved environmental temperature range is -10°C to +55°C
INSIDE THE BOX
• 1 x Output Module
• 1 x Product manual
• 1 x Quick start guide
• 1 x QR code
MOUNTING STEPS
The Input Module is designed to meet IP65 rating, suitable for external mounting.
Proceed as follows to complete the device installation.
Remove the lid from the back box, removing the screws
on the corners.
1
3
2
4
BATTERY
COMPARTMENTS
• Remove the appropriate knock out on the underside or lower
rear of the casing, install the M16/20 IP rated gland.
• Note: pay attention to avoid damages to the PCB, while
removing the knock out, or remove it before starting.
• Ensure the switch on the PCB is in position ON.
• Fit the 2x CR123A batteries ensuring you have checked
they are the correct way round observing the polarity
indications on the PCB.
• The LED will signal 4 times red.
• Move the switch on the PCBto position 1. The LED will blink
few seconds green and then signal alternatively green/red
4 times.
LED
DIP
SWITCH
ON 1
• To retain IP rating, please ensure you use the outer holes
on the casing.
• Using a pencil, mark through the outer holes on the desired
surface you will attach the unit to.
• Using a suitable-sized drill bit (6 mm) drill the marked screw
points on your chosen surface.
• Ensure you use the correct fixings for the type of surface
you are mounting to.
• Screw the backbox to the desired surface using all fixing holes
and appropriate-sized roundhead screws (not countersunk).
EOL
TW-MO-SB-01
WIRELESS BATTERY POWERED OUTPUT MODULE
QUICK START GUIDE
ARGUS SECURITY SRL, VIA DEL CANNETO, 14, 34015 MUGGIA, (TS), ITALY
T: +39-040.23.96.411, E: info@argussecurity.it, W: www.argussecurity.it
+
-
+
-
L50-MOSB-0001 (Rev_P.1)
THE BOX
Taurus QR code
Manual QR code
Product code
Product name
TW-MO-SB-01
Wireless battery
powered output module
L50-MOSB-0001 (Rev_P.4)
THE BOX
QR code
Part number
Product name
UNBOXING
• When unboxing the output module you will find the unit and its lid.
• This comes with pre-formed mounting holes to drill out and mount the backbox.
• Securing screws are supplied for the lid.
• A resistor pack is supplied for the monitored load connection (10KΩ R ).
For more information, please refer to the complete product manual.
IMPORTANT TO CONSIDER
When mounting a wireless device a comprehensive radio survey
should have been carried out to establish the location that provides
the best coverage and optimum reach. Taking into consideration the building
structure and materials, the survey identifies the wireless infrastructure
required and product locations for optimum performance, identifying
any factor that could prevent radio integrity.
Avoid fixing or mounting the unit close to the following:
• Equipment that utilises large electrical currents
• Large metal objects or structures
• Fluorescent lighting fittings
• Metal ceiling structures
• IT cabling.
Keep 2 meters minimum spacing between other wireless equipment
in the area to avoid signal interference.
EN54 approved environmental temperature range is -10°C to +55°C
INSIDE THE BOX
• 1 x Output Module
• 1 x Product manual
• 1 x Quick start guide
• 1 x QR code
MOUNTING STEPS
The Input Module is designed to meet IP65 rating, suitable for external mounting.
Proceed as follows to complete the device installation.
Remove the lid from the back box, removing the screws
on the corners.
1
3
2
4
BATTERY
COMPARTMENTS
• Remove the appropriate knock out on the underside or lower
rear of the casing, install the M16/20 IP rated gland.
• Note: pay attention to avoid damages to the PCB, while
removing the knock out, or remove it before starting.
• Ensure the switch on the PCB is in position ON.
• Fit the 2x CR123A batteries ensuring you have checked
they are the correct way round observing the polarity
indications on the PCB.
• The LED will signal 4 times red.
• Move the switch on the PCB to position 1. The LED will blink
few seconds green and then signal alternatively green/red
4 times.
LED
DIP
SWITCH
ON 1
• To retain IP rating, please ensure you use the outer holes
on the casing.
• Using a pencil, mark through the outer holes on the desired
surface you will attach the unit to.
• Using a suitable-sized drill bit (6 mm) drill the marked screw
points on your chosen surface.
• Ensure you use the correct fixings for the type of surface
you are mounting to.
• Screw the backbox to the desired surface using all fixing holes
and appropriate-sized roundhead screws (not countersunk).
EOL
TW-MO-SB-01
WIRELESS BATTERY POWERED OUTPUT MODULE
QUICK START GUIDE
ARGUS SECURITY SRL, VIA DEL CANNETO, 14, 34015 MUGGIA, (TS), ITALY
T: +39-040.23.96.411, E: info@argussecurity.it, W: www.argussecurity.it
+
-
+
-
L50-MOSB-0001 (Rev_P.1)
THE BOX
Taurus QR code
Manual QR code
Product code
Product name
TW-MO-SB-01
Wireless battery
powered output module
L50-MOSB-0001 (Rev_P.4)
THE BOX
QR code
Part number
Product name
UNBOXING
• When unboxing the output module you will find the unit and its lid.
• This comes with pre-formed mounting holes to drill out and mount the backbox.
• Securing screws are supplied for the lid.
• A resistor pack is supplied for the monitored load connection (10KΩ R ).
For more information, please refer to the complete product manual.
IMPORTANT TO CONSIDER
When mounting a wireless device a comprehensive radio survey
should have been carried out to establish the location that provides
the best coverage and optimum reach. Taking into consideration the building
structure and materials, the survey identifies the wireless infrastructure
required and product locations for optimum performance, identifying
any factor that could prevent radio integrity.
Avoid fixing or mounting the unit close to the following:
• Equipment that utilises large electrical currents
• Large metal objects or structures
• Fluorescent lighting fittings
• Metal ceiling structures
• IT cabling.
Keep 2 meters minimum spacing between other wireless equipment
in the area to avoid signal interference.
EN54 approved environmental temperature range is -10°C to +55°C
INSIDE THE BOX
• 1 x Output Module
• 1 x Product manual
• 1 x Quick start guide
MOUNTING STEPS
The Input Module is designed to meet IP65 rating, suitable for external mounting.
Proceed as follows to complete the device installation.
Remove the lid from the back box, removing the screws
on the corners.
1
3
2
4
BATTERY
COMPARTMENTS
• Remove the appropriate knock out on the underside or lower
rear of the casing, install the M16/20 IP rated gland.
• Note: pay attention to avoid damages to the PCB, while
removing the knock out, or remove it before starting.
• Ensure the switch on the PCB is in position ON.
• Fit the 2x CR123A batteries ensuring you have checked
they are the correct way round observing the polarity
indications on the PCB.
• The LED will signal 4 times red.
• Move the switch on the PCB to position 1. The LED will blink
few seconds green and then signal alternatively green/red
4 times.
LED
DIP
SWITCH
ON 1
• To retain IP rating, please ensure you use the outer holes
on the casing.
• Using a pencil, mark through the outer holes on the desired
surface you will attach the unit to.
• Using a suitable-sized drill bit (6 mm) drill the marked screw
points on your chosen surface.
• Ensure you use the correct fixings for the type of surface
you are mounting to.
• Screw the backbox to the desired surface using all fixing holes
and appropriate-sized roundhead screws (not countersunk).
EOL
TW-MO-SB-01
WIRELESS BATTERY POWERED OUTPUT MODULE
QUICK START GUIDE
ARGUS SECURITY SRL, VIA DEL CANNETO, 14, 34015 MUGGIA, (TS), ITALY
T: +39-040.23.96.411, E: info@argussecurity.it, W: www.argussecurity.it
+
-
+
-
L50-MOSB-0001 (Rev_P.1)
THE BOX
Taurus QR code
Manual QR code
Product code
Product name
TW-MO-SB-01
Wireless battery
powered output module
L50-MOSB-0001 (Rev_P.4)
THE BOX
QR code
Part number
Product name
UNBOXING
• When unbo[LQJWKHRXWSXWPRGXOH\RXZLOOçQGWKHXQLWDQGLWVOLG
• TKLVFRPHVZLWKSUHIRUPHGPRXQWLQJKROHVWRGULOORXWDQGPRXQWWKHEDFNEo[
• 6HFXULQJVFUHZVDUHVXSSOLHGIRUWKHOLG
• $UHVLVWRUSDFNLVVXSSOLHGIRUWKHPRQLWRUHGORDGFRQQHFWLRQ.Ω5
FRUPRUHLQIRUPDWLRQSOHDVHUHIHUWRWKHFRPSOHWHSURGXFWPDQXDO
IMPORTANT TO CONSIDER
WKHQPRXQWLQJDZLUHOHVVGHYLFHDFRPSUHKHQVLYHUDGLRVXUYH\
VKRXOGKDYHEHHQFDUULHGRXWWRHVWDEOLVKWKHORFDWLRQWKDWSURYLGHV
WKHEHVWFRYHUDJHDQGRSWLPXPUHDFKTDNLQJLQWRFRQVLGHUDWLRQWKHEXLOGLQJ
VWUXFWXUHDQGPDWHULDOVWKHVXUYH\LGHQWLçHVWKHZLUHOHVVLQIUDVWUXFWXUH
UHTXLUHGDQGSURGXFWORFDWLRQVIRURSWLPXPSHUIRUPDQFHLGHQWLI\LQJ
DQ\IDFWRUWKDWFRXOGSUHYHQWUDGLRLQWHJULWy
AYRLGç[LQJRUPRXQWLQJWKHXQLWFORVHWRWKHIROORZLQJ
• ETXLSPHQWWKDWXWLOLVHVODUJHHOHFWULFDOFXUUHQWV
• LDUJHPHWDOREMHFWVRUVWUXFWXUHV
• FOXRUHVFHQWOLJKWLQJçWWLQJV
à0HWDOFHLOLQJVWUXFWXUHV
à,7FDEOLQJ
.HHSPHWHUVPLQLPXPVSDFLQJEHWZHHQRWKHUZLUHOHVVHTXLSPHQW
LQWKHDUHDWRDYRLGVLJQDOLQWHUIHUHQFH
(1DSSURYHGHQYLURQPHQWDOWHPSHUDWXUHUDQJHLVr&WRr&
INSIDE THE BOX
à[2XWSXW0RGXOH
à[3URGXFWPDQXDO
MOUNTING STEPS
TKH,QSXW0RGXOHLVGHVLJQHGWRPHHW,3UDWLQJVXLWDEOHIRUe[WHUQDOPRXQWLQJ
3URFHHGDVIROORZVWRFRPSOHWHWKHGHYLFHLQVWDOODWLRQ
RHPRYHWKHOLGIURPWKHEDFNEo[UHPRYLQJWKHVFUHZV
RQWKHFRUQHUV
1
3
2
4
BATTERY
&20PARTMENTS
• RemRYHthe appropriatHNQRFNRXW on tKHXQGHUVide or lower
UHDURIWKHFDVLQJLQVWDOOWKH0,3UDWHGJODQG
à1RWHSD\DWWHQWLRQWRDYRLGGDPDJHVWRWKH3&%ZKLOH
UHPRYLQJWKHNQRFNRXWRUUHPRYHLWEHIRUHVWDUWLQJ
à(QVXUHWKHVZLWFKRQWKH3&%LVLQSRVLWLRQ21
• FLWWKH[&5$EDWWHULHVHQVXULQJ\RXKDYHFKHFNHG
WKH\DUHWKHFRUUHFWZD\URXQGREVHUYLQJWKHSRODULW\
LQGLFDWLRQVRQWKH3&%
• TKH/('ZLOOVLJQDOWLPHVUHG
• 0RYHWKHVZitch on tKH3&Bto pRVitiRQThe LED will blinN
IHZVHFRQGVJUHHQDQGWKHQVLJQDODOWHUQDWLYHO\JUHHQUHG
WLPHV
LED
DIP
SWIT&+
21
• TRUHWDLQ,3UDWLQJSOHDVHHQVXUH\RXXVHWKHRXWHUKROHV
RQWKHFDVLQJ
à8VLQJDSHQFLOPDUNWKURXJKWKHRXWHUKROHVRQWKHGHVLUHG
VXUIDFH\RXZLOODWWDFKWKHXQLWWR
• 8VLQJ a VXLtaEOHVLzed drill bit Pm) drill the maUNHGVFUHw
pointVon yRXUFKRVHQ VXUIace
à(QVXUH\RXXVHWKHFRUUHFWç[LQJVIRUWKHW\SHRIVXUIDFH
\RXDUHPRXQWLQJWR
• Screw the baFNEox to the GHViUHGVXUIaFHXVLQJ all ç[ing holeV
and appropriatHVLzed URXQGKHDGVFUHZV QRt FRXQWHUVXQN
(2/
TW-MO-SB-01
WIRELESS BATTERY POWERED OUTPUT MODULE
48,&.6TART GUIDE
ARGUS SECURITY SRL9,$'(/&$11(T208**,A76,TALY
T(LQIR#DUJXVVHFXULWyLW:wwwDUJXVVHFXULWyLW
+
-
+
-
/026%RHYBP
THE BOX
TDXUXV45FRGH
Manual QR code
Product code
Product name
TW-MO-SB-01
Wireless battery
powered output module
L50-MOSB-0001 (Rev_P.3)
THE BOX
QR code
Part number
Product name
UNBOXING
• When unboxing the output module you will find the unit and its lid.
• This comes with pre-formed mounting holes to drill out and mount the backbox.
• Securing screws are supplied for the lid.
• A resistor pack is supplied for the monitored load connection (10K: R ).
For more information, please refer to the complete product manual.
IMPORTANT TO CONSIDER
When mounting a wireless device a comprehensive radio survey
should have been carried out to establish the location that provides
the best coverage and optimum reach. Taking into consideration the building
structure and materials, the survey identifies the wireless infrastructure
required and product locations for optimum performance, identifying
any factor that could prevent radio integrity.
Avoid fixing or mounting the unit close to the following:
• Equipment that utilises large electrical currents
• Large metal objects or structures
• Fluorescent lighting fittings
• Metal ceiling structures
• IT cabling.
Keep 2 meters minimum spacing between other wireless equipment
in the area to avoid signal interference.
EN54 approved environmental temperature range is -10°C to +55°C
INSIDE THE BOX
• 1 x Output Module
• 2 x CR123A batteries
• 4 x Securing screws
• 1 x Resistor pack
• 1 x Product manual
MOUNTING STEPS
The Input Module is designed to meet IP65 rating, suitable for external mounting.
Proceed as follows to complete the device installation.
Remove the lid from the back box, removing the screws
on the corners.
1
3
2
4
BATTERY
COMPARTMENTS
• Remove the appropriate knock out on the underside or lower
rear of the casing, install the M16/20 IP rated gland.
• Note: pay attention to avoid damages to the PCB, while
removing the knock out, or remove it before starting.
• Ensure the switch on the PCB is in position ON.
• Fit the 2x CR123A batteries ensuring you have checked
they are the correct way round observing the polarity
indications on the PCB.
• The LED will signal 4 times red.
• Move the switch on the PCB to position 1. The LED will blink
few seconds green and then signal alternatively green/red
4 times.
LED
DIP
SWITCH
ON 1
• To retain IP rating, please ensure you use the outer holes
on the casing.
• Using a pencil, mark through the outer holes on the desired
surface you will attach the unit to.
• Using a suitable-sized drill bit (6 mm) drill the marked screw
points on your chosen surface.
• Ensure you use the correct fixings for the type of surface
you are mounting to.
• Screw the backbox to the desired surface using all fixing holes
and appropriate-sized roundhead screws (not countersunk).
EOL
TW-MO-SB-01
WIRELESS BATTERY POWERED OUTPUT MODULE
QUICK START GUIDE
ARGUS SECURITY SRL, VIA DEL CANNETO, 14, 34015 MUGGIA, (TS), ITALY
T: +39-040.23.96.411, E: info@argussecurity.it, W: www.argussecurity.it
+
-
+
-
L50-MOSB-0001 (Rev_P.1)
à[&5$EDWWHULHV
%DWWHULHVQRWLQFOXGHGIRU
LWHPFRGH7:026%1%
à[6HFXULQJVFUHZV
Available also without batteries: TW-MO-SB-01/NB
• 2 x CR123A batteries
Batteries not included for
item code TW-MO-SB-01/NB
• 4 x Securing screws
• 1 x Resistor pack
Available also without batteries: TW-MO-SB-01/NB
• 2 x CR123A batteries
Batteries not included for
item code TW-MO-SB-01/NB
• 4 x Securing screws
• 1 x Resistor pack
Available also without batteries: TW-MO-SB-01/NB
• 2 x CR123A batteries
Batteries not included for
item code TW-MO-SB-01/NB
• 4 x Securing screws
• 1 x Resistor pack
Available also without batteries: TW-MO-SB-01/NB
