Smartech LBT-1.DO4 User manual

USER MANUAL
Longo Bluetooth Products
LBT-1.DO4
Bluetooth Mesh Triac output
module
Version 2
SMARTEH d.o.o. / Poljubinj 114 / 5220 Tolmin / Slovenia / Tel.: [phone] / e-mail: [e-mail] / www.smarteh.si

Longo Bluetooth Products LBT-1.DO4
Written by MARTEH d.o.o.
Copyright © 2023, MARTEH d.o.o.
User Manual
Document Version: 2
May 2023
i

Longo Bluetooth Products LBT-1.DO4
TANDARD AND PROVI ION : tandards, recommendations,
regulations and provisions of the country in which the devices will
operate, must be considered while planning and setting up electrical
devices. Work on 100 .. 240 V AC network is allowed for authorized
personnel only.
DANGER WARNING : Devices or modules must be protected from
moisture, dirt and damage during transport, storing and operation.
WARRANTY CONDITION : For all modules LBT-1 – if no modifications
are performed upon and are correctly connected by authorized
personnel – in consideration of maximum allowed connecting power,
warranty of 24 months is valid from the date of sale to the end buyer,
but not more than 36 months after delivery from marteh. In case of
claims within warranty time, which are based on material
malfunctions the producer offers free replacement. The method of
return of malfunctioned module, together with description, can be
arranged with our authorized representative. Warranty does not
include damage due to transport or because of unconsidered
corresponding regulations of the country, where the module is
installed.
This device must be connected properly by the provided connection
scheme in this manual. Misconnections may result in device damage,
fire or personal injury.
Hazardous voltage in the device can cause electric shock and may
result in personal injury or death.
NEVER ERVICE THI PRODUCT YOUR ELF!
This device must not be installed in the systems critical for life (e.g.
medical devices, aircrafts, etc.).
If the device is used in a manner not specified by the manufacturer,
the degree of protection provided by the equipment may be impaired.
Waste electrical and electronic equipment (WEEE) must be collected
separately!
LBT-1 devices are developed considering the following standards:
•EMC: EN 303 446-1
•LVD: EN 60669-2-1
marteh d.o.o. operates a policy of continuous development.
Therefore we reserve the right to make changes and improvements to
any of the products described in this manual without any prior notice.
MANUFACTURER:
MARTEH d.o.o.
Poljubinj 114
5220 Tolmin
lovenia
ii

Longo Bluetooth Products LBT-1.DO4
Longo Bluetooth Products LBT-1.D 4
1.ABBREVIATION ...............................................................................1
2.DE CRIPTION..................................................................................2
3.FEATURE ......................................................................................3
4.OPERATION....................................................................................4
4.1.Other triac output module functions..............................................5
4.2.Operation parameters................................................................6
5.IN TALLATION.................................................................................9
5.1.Connection scheme...................................................................9
5.2.Mounting instructions...............................................................11
6. Y TEM OPERATION ........................................................................14
6.1.Interference warning ...............................................................14
7.TECHNICAL PECIFICATION ...............................................................15
8.MODULE LABELING..........................................................................16
9.CHANGE ....................................................................................17
10.NOTE .......................................................................................18
iii

Longo Bluetooth Products LBT-1.DO4
1.ABBREVIATI NS
LED Light Emitted Diode
PLC Programmable Logic Controller
PC Personal Computer
OpCode Message Option Code
1

Longo Bluetooth Products LBT-1.DO4
2.DESCRIPTI N
LBT-1.DO4 Bluetooth Mesh two triac output module is designed to be used as a shades or curtains
motor control module with RM current and voltage measuring possibility. The module can operate
with a wide range of AC voltages. It can be placed inside the 60mm diameter flush mounting box. It
can also be placed close to shades or curtains motor. witch input is provided to have the possibility
of manually switching On and Off the two triac outputs. This input can detect 50/60 HZ for triac 1
control and 25/30 HZ for triac 2 control. Two positions push button switch with an appropriate
diode as 1N4007 should be connected to the switch input line wire as shown in Figure 4. Only one
triac output, triac output 1 or triac output 2, can operate at the time.
LBT-1.DO4 Bluetooth Mesh two triac output module can only operate with marteh LBT-1.GWx
Modbus RTU Bluetooth Mesh gateway connected to the same Bluetooth Mesh network. LBT-1.GWx
Modbus RTU gateway is connected to the main control device as marteh LPC-3.GOT.012 7" PLC
based Touch panel, any other PLC or any PC with Modbus RTU communication. Besides marteh
Bluetooth Mesh devices, other standard Bluetooth Mesh devices can be integrated into above
mentioned Bluetooth Mesh network. More than a hundred Bluetooth Mesh devices can be provisioned
and can operate in a single Bluetooth Mesh network.
2

Longo Bluetooth Products LBT-1.DO4
3.FEATURES
Figure 1: LBT-1.DO4
Table 1: Technical data
Communication standard: Bluetooth Mesh is a low power wireless mesh protocol and allows
device to device communication and device to main control device communication.
Radio frequency: 2.4 GHz
Radio range for direct connection: < 30 m, depending on application and building.
By using Bluetooth Mesh topology, much bigger distances can be achieved.
Power supply: 90 .. 264 V AC
Ambient temperature: 0 .. 40 °C
torage temperature: -20 .. 60 °C
tatus indicators: red and green LED
2 x Triac output, 0.7 A continuous per output/ 1 A pulsing per output
RM current and voltage measurement, power consumption measurement
witch digital input
Mounting in flush mounting box
3

Longo Bluetooth Products LBT-1.DO4
4. PERATI N
LBT-1.DO4 Bluetooth Mesh Triac output module can only operate with marteh LBT-1.GWx Modbus
RTU Bluetooth Mesh gateway while provisioned to the same Bluetooth Mesh network.
Figure 2: LBT-1.DO4 device connection
Figure 3: Bluetooth Mesh system topology
4

Longo Bluetooth Products LBT-1.DO4
4.1. ther triac output module functions
• Factory reset: This function will delete all Bluetooth Mesh network parameters stored on
LBT-1.DO4 triac output module and will restore to the conditions of the initial programming,
ready for provisioning. ee Table 5 for more information.
5

Longo Bluetooth Products LBT-1.DO4
4.2. peration parameters
LBT-1.DO4 Bluetooth Mesh Triac output module accepts a set of operation codes as specified in
below tables 2 to 4.
LBT-1.DO4 Bluetooth Mesh output module is communicating with main control device as marteh
LPC-3.GOT.012 via marteh LBT-1.GWx Modbus RTU Bluetooth Mesh gateway.
All communication between main control device as LPC-3.GOT.012 or similar is performed by using
Modbus RTU communication. Individual Bluetooth Mesh node configuration data should be observed
by using network provisioning tool.
Table 2: 4xxxx, Holding registers, Modbus RTU to Bluetooth Mesh gateway
Reg. Name Description Raw → Engineering data
10 Execute command Execute command for Read
and/or Write by toggling bit
Bit0 toggle → Write
Bit1 toggle → Read
11 Destination address*
Destination node address. Can
be a unicast, group or virtual
address
0 .. 65535 0 .. 65535→
12 Element index* ending node model element
index 0 .. 65535 0 .. 65535→
13 Vendor ID* Vendor ID of the sending node
model 0 .. 65535 0 .. 65535→
14 Model ID* Model ID of the sending node
model 0 .. 65535 0 .. 65535→
16 Virtual address index* Index of the destination Label
UUID 0 .. 65535 0 .. 65535→
17 Application key index* The application key index used 0 .. 65535 0 .. 65535→
18 Option code** Refer to the option code table 0 .. 63 →0 .. 63
19 Payload byte length** Refer to the option code table 1 .. 10 →1 .. 10 bytes
20 Payload word[0]** Refer to the option code table 0 .. 65535 0 .. 65535→
21 Payload word[1]** Refer to the option code table 0 .. 65535 0 .. 65535→
22 Payload word[2]** Refer to the option code table 0 .. 65535 0 .. 65535→
23 Payload word[3]** Refer to the option code table 0 .. 65535 0 .. 65535→
24 Payload word[4]** Refer to the option code table 0 .. 65535 0 .. 65535→
* Observed from network provisioning tool
** User defined parameters, refer to option code table
6

Longo Bluetooth Products LBT-1.DO4
Table 3: 3xxxx, Input registers, Modbus RTU to Bluetooth Mesh gateway
Reg. Name Description Raw → Engineering data
10 Messages pending Number of messages pending in
receiving buffer 1 .. 10 →1 .. 10
11 Destination address
Destination node address. Can
be a unicast, group or virtual
address
0 .. 65535 0 .. 65535→
12 Element index ending node model element
index 0 .. 65535 0 .. 65535→
13 Vendor ID Vendor ID of the sending node
model 0 .. 65535 0 .. 65535→
14 Model ID Model ID of the sending node
model 0 .. 65535 0 .. 65535→
15 ource address Unicast address of the node
model which sent the message 0 .. 65535 0 .. 65535→
16 Virtual address index Index of the destination Label
UUID 0 .. 65535 0 .. 65535→
17 Application key index The application key index used 0 .. 65535 0 .. 65535→
18 Option code Refer to the option code table 0 .. 63 0 .. 63→
19 Payload length Refer to the option code table 1 .. 10 1 .. 10 bytes→
20 Payload word[0] Refer to the option code table 0 .. 65535 0 .. 65535→
21 Payload word[1] Refer to the option code table 0 .. 65535 0 .. 65535→
22 Payload word[2] Refer to the option code table 0 .. 65535 0 .. 65535→
23 Payload word[3] Refer to the option code table 0 .. 65535 0 .. 65535→
24 Payload word[4] Refer to the option code table 0 .. 65535 0 .. 65535→
Table 4: Triac output LBT-1.D 4 option codes
ption
code Name Description Raw → Engineering data
1 FW version status Firmware version status 0 .. 65535 0 .. 65535→
2 Operation mode set Node operation mode
selection
0 →Not used
1 →Not used
2 →Not used
3 →Not used
4 →Reset
5 →Factory reset
7

Longo Bluetooth Products LBT-1.DO4
Table 4: Triac output LBT-1.D 4 option codes
9Wake up interval
command
Command to set the time
interval in which the device
wakes up and sends data
about the current and voltage
status
0 .. 65535 0 .. 65535 s→
10 Wake up interval status
tatus of the time interval in
which the device wakes up
and sends data about the
current and voltage status
0 .. 65535 0 .. 65535 s→
18 Voltage status Input voltage RM value 0 .. 65535 0 .. 6553.5 V→
19 Current status Load current RM value 0 .. 65535 0 .. 65.535 A→
40 Digital Out 1 command Load output 1 command, L1 0 OFF→
1 ON→
41 Digital Out 1 status tatus of load output 1, L1 0 OFF→
1 ON→
42 Digital Out 2 command Load output 2 command, L2 0 OFF→
1 ON→
43 Digital Out 2 status tatus of load output 2, L2 0 OFF→
1 ON→
53 Load output 1 switch
enable command
Command for enabling
switching on the load output
1 on W input
0 Disable→
1 Enable→
54 Load output 1 switch
enable status
Enable status of the W input
for load output 1
0 Disabled→
1 Enabled→
55 Load output 2 switch
enable command
Command for enabling
switching on the load output
2 on W input
0 Disable→
1 Enable→
56 Load output 2 switch
enable status
Enable status of the W input
for load output 2
0 Disabled→
1 Enabled→
8

Longo Bluetooth Products LBT-1.DO4
5.INSTALLATI N
5.1.Connection scheme
Figure 4: Example of connection scheme
9

Longo Bluetooth Products LBT-1.DO4
Figure 5: LBT-1.D 4 module
Table 5: Inputs and LEDs
K1.1 N1 Load output: neutral
K1.2 N Power supply input: neutral
K1.3 L2 Load output 2: line
K1.4 W witch input: line, 90 .. 264 V AC
K1.5 L1 Load output 1: line
K1.5 L Power supply input: line, 90 .. 264 V AC
LED1: red Error 2x blink inside 5 s time period = network/friend lost
3x blink inside 5 s time period = unprovisioned node
LED2: green tatus 1x blink = normal operation.
It's also feedback for 1 reed contact, when activated
with magnet.
1 Reed contact Mode setting contact
Inside 5 s time window, perform corresponding number of
swipes in duration of not less than 200 ms with permanent
magnet close to the window sensor 1 reed contact position.
Following window sensor action or mode will be set:
Number of swipes Action
________________________________
4 Reset
5 Factory reset
A hardware reset is triggered if reed contact is continuously
closed with a permanent magnet for more than 5 seconds.
10

Longo Bluetooth Products LBT-1.DO4
5.2.Mounting instructions
Figure 6: Housing dimensions
Dimensions in millimeters.
Figure 7: Mounting in flush mounting box
11

Longo Bluetooth Products LBT-1.DO4
Figure 8: Installation flowchart
12

Longo Bluetooth Products LBT-1.DO4
1. witching Off the main power supply.
2. Mount the module up to the provided place and wire the module according to the
connection scheme in Figure 4. Two position push button switch and appropriate diode as
1N4007 should be connected to the LBT-1.DO4 module switch input line wire
as shown on Figure 4.
3. witching On the main power supply.
4. After a few seconds Green or Red LED starts to blink, please see the flowchart above for
details.
5. If the module is not provisioned Red LED will blink 3x, the provisioning procedure has to be
started. Contact the producer for more details*.
6. Once provisioning is finished, the module will continue with the normal mode of operation
and this will be indicated as Green LED blinking once per 10 seconds.
Dismount in reverse order.
*N TE: marteh Bluetooth Mesh products are added and connected to a Bluetooth Mesh network by
using standard provisioning and configuration mobile apps tool such as nRF Mesh or similar.
Please contact producer for more detail information.
13

Longo Bluetooth Products LBT-1.DO4
6.SYSTEM PERATI N
LBT-1.DO4 Bluetooth Mesh triac output module can switch power to two triac outputs, usually to
power shade or curtain motors, based on 50/60Hz or 25/30Hz voltage present on module switch
input or based on Bluetooth Mash command. Only one triac output can operate at a time.
6.1.Interference warning
Common sources of unwanted interference are devices that generate high frequency signals. These
are typically computers, audio and video systems, electronics transformers, power supplies and
various ballasts. The distance of the LBT-1.DO4 two triac output module to the above mentioned
devices should be at least 0.5m or greater.
WARNING:
• In order to protect plants, systems, machines and network against cyber threats, necessary
to implement and continuously maintain up to date security concept.
• You are responsible for preventing unauthorized access to your plants, systems, machines and
networks and they are allowed to be connected to Internet only, when security measures like
firewalls, network segmentation, … are in place.
• We strongly recommend the updates and usage of latest version. Usage of version that are no
longer supported may increase the possibility of cyber threats.
14

Longo Bluetooth Products LBT-1.DO4
7.TECHNICAL SPECIFICATI NS
Table 7: Technical specifications
Power supply 90 .. 264 V AC, 50/60 Hz
Max. power consumption 1.5 W
Fuse 1 A (T-slow), 250 V
Load voltage ame as power supply voltage
Max. continuous load current per output 0.7 A
Max. load current per output, 50% On / 50% Off, pulse <100 s 1 A
Connection type crew type connectors for
stranded wire 0.75 to 2.5 mm2
RF communication interval Minimum 0.5 s
Dimensions (L x W x H) 53 x 38 x 25 mm
Weight 40 g
Ambient temperature 0 to 40 °C
Ambient humidity Max. 95 %, no condensation
Maximum altitude 2000 m
Mounting position Any
Transport and storage temperature -20 to 60 °C
Pollution degree 2
Over voltage category II
Electrical equipment Class II (double insulation)
Protection class IP 10
15

Longo Bluetooth Products LBT-1.DO4
8.M DULE LABELING
Figure 10: Label
Label (sample):
Label description:
1. XXX-N.ZZZ - full product name,
• XXX-N - product family,
• ZZZ.UUU – product,
2. P/N: AAABBBCCDDDEEE - part number,
• AAA - general code for product family,
• BBB - short product name,
• CCDDD - sequence code,
• CC - year of code opening,
• DDD - derivation code,
• EEE – version code (reserved for future HW and/or W firmware upgrades),
3. S/N: SSS-RR-YYXXXXXXXXX - serial number,
• SSS – short product name,
• RR – user code (test procedure, e.g. marteh person xxx),
• YY – year,
• XXXXXXXXX – current stack number,
4. D/C: WW/YY - date code,
• WW – week and,
• YY – year of production.
Optional:
• MAC,
• Symbols,
• WAMP,
• Other.
16
XXX-N.ZZZ.UUU
P/N: AAABBBCCDDDEEE
S/N: SSS-RR-YYXXXXXXXXX
D/C: WW/YY