Ariston AWD 121 NA User manual

Model type:
AWD121NA
Commercial code:
35356

mod.AWD121NA page 2
General notes
Technical Documentation guidelines
----------------------------------------------------------------------------------------------------------------------------------
-------------------------------------------------------------
You can find herewith some generic information to simplify cunsulting of technical documentation:
1. Models of same range share the same exploded views, which report the richest set of spare parts:generally, a model does not
necessarly have a related spare part for each particular shown on exploded views.
2. Some spare parts can not be represented directly on the exploded views (instruction booklets, specific kit, etc...). You can find
those codes in the spare parts list with the same reference of particular where spares are installed or with references 099, 999.
Instruction booklets, once managed, appear with 000 reference.
3. On the higher right site of each exploded view there is a serial number which indicates the beginning of the production of
certain range:some models might have more than an exploded view for a given category, each distinguished by a different serial
no.and linked to another spare parts list, In this case, serial no. is required to supply the right spare part code. Exploded view to be
considered is the one with a more recent serial no. but previous than the one of the model that needs assistance.
4.Exploded views might require further updates even after publishing. Addition of new spares will go on following the already
existing numeration references. Revision number of an exploded view is shown into last four digits of serial number into upper
right hand corner.
5.The spare parts list associated to an exploded view shows related codes of spares managed for a certain model; for each spare
part other informations are available:
REF: reference no of spare into a table; SUBSTITUTE: list of spare(s) which can replace a code but that keeps same functional
characteristics
INDUSTRIAL CODE: list of variables of a model (shown into model label) where such spare is used; NOTICE: code of
information(s) to refer to complete technical intervention, track for changes or to find correct spare part code.
6. Some notices, into a same section are generic therefore cannot be directly linked to a spare part. In order to assist a model in
the best way as possible, it is helpful to pay attention to all notices and constantly verify documentation updates
7.Technical documentation cover shows model name and its commercial codes

mod.AWD121NA page 3
1140110A Exploded views

mod.AWD121NA page 4
1140110A Spare parts
list
Ref. Code From To S/N Substitute Description Notice Industrial
000 C00116122 user instruct.bookl gb-es-f
001 C00090582 1 x C00116622 cabinet white n1040230 80353560000
n1040359
001 C00116622 cabinet white pw 80353560900
002 C00065186 1 x C00091882 pivot pin - drawer front 108.5x5
003 C00064784 bracket - timer support
004 C00099647 knob timer disc 'awd120na'
005 C00065180 1 x C00064506 wash timer knob white
006 C00064509 1 x C00117965 pushbutton white 0/i n1040359 80353560000
006 C00117965 pushbutton white pw 0/i 80353560900
007 C00099637 thermostat knob white awd120na n1040359 80353560000
007 C00099638 white dry timer knob awd120na 80353560000
007 C00116608 white knob thermostat pw 80353560900
007 C00116609 knob dryer white pw awd120na 80353560900
008 C00064507 pushbutton white n1040359 80353560000
008 C00116625 pushbutton white 0/i 80353560900
009 C00116105 control panel + handle awd121na 80353560000
009 C00116805 control panel + handle pw 80353560900
010 C00082825 1 x C00116624 door frame assy
011 C00065250 1 x C00116580 door handle kit n1040359 80353560000
011 C00116580 door handle kit pw lb2000 80353560900
012 C00110325 1 x C00116552 plinth white n1040359 80353560000
012 C00116552 plinth white pw 80353560900
013 C00087084 foot - m8 h = 2,3 cm
014 C00083828 spring for foot d =11 mm h = 8,5
015 C00065185 bolt m4,5 x 11
016 C00064541 hinge assy-outer case/door 180 n1040349 80353560000
016 C00115666 zama hinge 150° 80353560900
017 C00012687 self-tapping screw hi-lo 3,5x13
017 C00074149 bolt m4x9 tesrfr
019 C00064539 hinge plate door
022 C00065871 blanking plug
023 C00046666 collar for drain hose
023 C00099313 1 x C00116923 rear cover - white n1040359 80353560000
023 C00116923 rear cover - white pw 80353560900

mod.AWD121NA page 5
1140110A Spare parts
list
Ref. Code From To S/N Substitute Description Notice Industrial
024 C00084817 blanking plate-rear(test plug)
027 C00112436 1 x C00116618 top white + plate ariston n1040359 80353560000
027 C00116618 worktop - white pw aw121na 80353560900
028 C00046667 wiring stop
028 C00064550 drain hose holder
028 C00091904 cable clamp hose
029 C00099627 schakelaarplaat on-off 'awd120na'
030 C00090932 base cabinet plate usa normal ph

mod.AWD121NA page 6
1180240 Exploded views

mod.AWD121NA page 7
1180240 Spare parts list
Ref. Code From To S/N Substitute Description Notice Industrial
001 C00064786 1 x C00143260 bolt m8x23 torx tefl
002 C00013563 bearing 25 x52 x 15 6205-2z
003 C00064785 bolt m8x22 tb6lt
004 C00002591 bearing 20x47x14
005 C00096186 standard oil seal cv4 30 x 52/65 x n1040300
n1040326
006 C00080651 1 x C00032847 rear support
1 x C00114387
1 x C00114390
1 x C00145190
007 C00088408 bolt + washer
008 C00087811 upper counterweight 8,2 kg
010 C00080650 front support
011 C00080652 bolt m8x36 tefl. zig. p/p
012 C00064515 anchorage pad - suspension
013 C00080660 suspension spring - tank
014 C00080653 spacer
015 C00110429 door bellows seal wd 28-28 cm
016 C00064546 clamping ring - bellows seal front
017 C00064547 bellows clamp (tank front)
018 C00092178 front counterweight
019 C00092411 hose clamp
020 C00092174 hose tank to filter oko
021 C00092412 hose clamp
022 C00091148 1 x C00094908 clamp d=79 mm
023 C00065152 nut romob m6x22x1,5
024 C00047136 1 x C00144571 nut romob m8
025 C00093848 cradle outer- set
026 C00093885 shock absorber 120 n 8,15 mm
027 C00064789 wash paddles (extractable) 46 l
028 C00094281 1 x C00094275 outer- set 46 l. evo ii n1040300
1 x C00094280 n1040371
030 C00093750 bolt zink m8x40
031 C00092273 hose dispenser to tank
032 C00096077 bearing spider assembly n1040300

mod.AWD121NA page 8
1180240 Spare parts list
Ref. Code From To S/N Substitute Description Notice Industrial
033 C00074211 drum pulley d=210 mm h=20 mm
034 C00074218 belt l=1046 - 1051 mm h8 (hl)
099 C00001109 loctite 270 10 gr.
099 C00033026 ambljgon grease ta 100 gr.

mod.AWD121NA page 9
1180320A Exploded views

mod.AWD121NA page 10
1180320A Spare parts
list
Ref. Code From To S/N Substitute Description Notice Industrial
001 C00098928 supply cable 1,50 mt usa
003 C00019902 plastic -u- to make drain hose
004 C00091775 drain hose to sink
005 C00088394 push button switch na idc
005 C00090218 deviator switch (on-off)
007 C00086663 pilot light red 12 v rast 2.5
008 C00090195 programme select elbi 1665 rast
009 C00085195 1 x C00143096 potentiometer 8 pos. idc rast 2,5
010 C00064537 support - pressure switch
011 C00046152 additive container
013 C00046148 soap dispenser drawer (rotary)
014 C00092176 dispenser body
015 C00090200 pressure switch 1l 90-65
016 C00092412 hose clamp
017 C00092170 pipe pressostat l= 470mm. evo ii
018 C00098754 anti-vibration hose (foam) l= 330
021 C00092173 air trap x oko
023 C00090199 door interlock rold da rst 5usa idc
024 C00045027 filter element kit (hl)
025 C00112504 self cleaning pump 120v 60hz
026 C00074152 bolt m6x30
027 C00074151 rubber bush - motor mount
028 C00074153 spacer motor support l= 187 mm
030 C00040932 self locking nut m6
031 C00090196 motor ceset mcc61 usa 6kg
031 C00145001 1 x C00196554 brush motor ceset eame 6170
032 C00110422 hole for heating element
033 C00091054 coil to protect module 2002
034 C00116123 eeprom evoi awd121na sw
035 C00109898 module (less eeprom) wd usa mdl
036 C00066292 insulated tweezers
036 C00095669 hardware key mk1 n1040317
036 C00099862 serial cable lb2000 evoii - pc
037 C00046157 stopper detergent container
039 C00064534 seal - electrovale/dispenser

mod.AWD121NA page 11
1180320A Spare parts
list
Ref. Code From To S/N Substitute Description Notice Industrial
039 C00110452 electrovalve 1way 5,5lt hot rst2.5
039 C00116117 3-way electrovalve 1e-3u 7 l
040 C00005572 sealing washer-mains inlet hose
041 C00005781 inlet hose filter
042 C00112930 inlet hose with usa
043 C00066514 electrovalve support 2 ev
044 C00116106 wiring awd121na
045 C00092348 self-scraping screw 3,5x8
046 C00099625 reading desk awd120na pr47
047 C00065733 support - programme guide tbc
048 C00058523 pillar retainer-heating element
051 C00116112 hopper cover awd-na
052 C00080767 temperature sensor (hl)
053 C00014917 grommet - thermostat

mod.AWD121NA page 12
1180410 Exploded views

mod.AWD121NA page 13
1180410 Spare parts list
Ref. Code From To S/N Substitute Description Notice Industrial
001 C00087921 screw amsp m3.5x30t.e.(s/n
002 C00080775 1 x C00199364 thermal cut-out cable
003 C00089982 thermostat
003 C00098739 temperature sensor ntc rast 2,5
004 C00080768 o-ring d= 27 x 23,5 x 1,78 wd
005 C00110433 dryer heating element 1200 watt
006 C00032847 blower manifold seal
007 C00033210 hose clamp fastex 350 mm x 7.8
008 C00032845 restrictor seat
009 C00080960 self blocking nut m5
010 C00080959 connection gasket
010 C00097378 connection gasket
011 C00080771 clip
012 C00080773 fixing screw for lint filter
013 C00080772 60211... 1 x C00143947 lint filter 80353560000
1 x C00143949 80353560900
013 C00143949 60212... lint filter 80353560900
014 C00080774 hose clamp
015 C00080770 60211... 1 x C00143947 steam condenser 80353560000
1 x C00143949 80353560900
015 C00143947 60212... steam condenser 80353560900
016 C00080769 hose electrovalve condenser
017 C00032844 seal - condenser / tank
018 C00038358 bolt m8x16 (dry loc)
019 C00032972 blower fixing nut
020 C00080658 blower fan for motor (087920-
021 C00054790 screw trilob m5 x 16 tcb t.e. st
022 C00087919 blower manifold kit
023 C00110434 dryer fan motor 115v.60hz
024 C00114390 fixing screw for blower manifold

mod.AWD121NA page 14
Notices
n1040061: Trouble-shooting.
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Intervention procedure on 2000 washing machines
1. Reading the error code
The fault on the appliance is signalled via:
1. the continuous rotation of the selector knob
2. the action, for the first 4', of the electrovalve and the drain pump
3. the door becomes unlocked
4. the led flashes:
the number of flashes indicates the fault code; the code should be read as follows:
· each fast flash (2/3 flashes of the led very close together) represents one code value
· the fault code is evaluated by counting the number of flashes occurring at 3/4" intervals from one another
· stop counting when the washing machine waits the equivalent of approximately 8/9" between flashes
· the procedure is repeated by the appliance cyclically
E.g.: F03
(FIGURE NT 00)
2. Autotest
Should the washing machine not be signalling an error, you can check it using a serial key and using a particular autotest cycle,
which is to be activated as follows:
1. bring the washing machine to reset position (coloured ball) for at least 5" and wait until the led flashes on reset mode
2. insert the hardware key into the serial outlet
3. position the switch situated on the key in TEST position
4. wait for the door to lock and for the selector to start turning
5. position the switch situated on the key in PC position
the appliance will carry out the following cycle:
· selector moves on up to position 0 (12h if the appliance has a delay, programme 1 if it has no delay)
· loads the wash electrovalve for approx. 10"
· loads the pre-wash electrovalve for approx. 10"
· loads the wash electrovalve and pre-wash electrovalve at the same time until the pressure switch is on full
· heats up to 30° and moves the motor in both directions
· selector moves on for 9 notches
· drains and spins
· the selector knob stops on one of the reset positions
· STOP

mod.AWD121NA page 15
The test cycle can be repeated as many times as you wish following the same procedures
The test cycle can be interrupted by positioning the selector knob on one of the reset positions.
3. Intervention in the event of a Fault
In the event of a fault, the procedure to go by is as follows:
F01: Triac Short circuit
Overhaul CNE
Replace Card
F02: Blocked Motor, Short-circuited/Open Tachometry
Overhaul CNE
Overhaul Motor connector
Control CNE Continuity/Motor Connector
Control Motor Windings
Control Tachometry Windings
Replace Card
F03: Open/Short-Circuited NTC Found
Overhaul CNA
Control NTC Wiring
Control CNA/NTC Wiring Continuity
Replace NTC
Replace Card
F04: Overflow and Pressure Switch Empty found at the same time (Pressure Switch stuck on Empty)
Overhaul CN1
Overhaul Pressure Switch Contacts
Control CN1/Pressure Switch Continuity
Replace Pressure Switch
Replace Card
F05: Blocked Pump or Pressure Switch stuck on Empty Found
Overhaul CNF (pump connector)
Overhaul Pump Connector
Control Pump Filter
Control Pump Windings
Change Pump
Replace Card
F06: Selector Error (a part no. cannot be found)
Overhaul CND (selector connector)
Overhaul Selector Connector
Control Selector/CND Continuity
Control Selector Motor
Replace Selector
Replace Card
F07: Resistance Relay Stuck
Overhaul CN1
Overhaul CN1
Overhaul Resistance Connection
Replace Card

mod.AWD121NA page 16
Overhaul Resistance Connection
Replace Card
F08: Resistance Missing or Pressure Switch stuck on Full Found
Overhaul CN1
Overhaul Resistance Connection
Overhaul Pressure Switch Connection
Replace Resistance
Replace Pressure Switch
Replace Card
F09: Machine Setup Error Found
Control Microprocessor Version
Ask for EEPROM Spare Part indicating Microprocessor version
F10: Pressure Switch Empty and Full or neither Empty nor Full Pressure Switch Found
Overhaul CN1
Overhaul Pressure Switch Wiring
Control CN1/Pressure Switch Continuity
Replace Pressure Switch
Replace Card
F11: Pump Feedback Missing
Overhaul CN1
Overhaul CNF
Overhaul Pump Connector
Overhaul Pressure Switch Connector
Control Pump Windings
Replace Pump
Replace Card
F12 SPECIFIC FOR LVB2000 INDESIT EVOLUTION / DIALOGIC.
F12: Lack of Display card-Main Card Communication
1. Check the effectiveness of contacts on CNC Connector Card
2. Overhaul 8-way connector on Display card
3. Check continuity of CNC-CN 8 way connector
4. Replace Main Card
5. Replace Display Card
F13: NTC wiring harness disconnected from the dryer system
1. Check the efficiency of the terminals on the CNA connector board
2. Check NTC wiring harness
3. Check the wiring harness continuity of the CNA / NTC connectors
4. Replace NTC
5. Replace terminal board
F14: Dryer connector open or not connected
1. Check the efficiency of the terminals on the CNI connector board
2. Overhaul CN1
3. Overhaul connector connection
4. Replace the board.Merloni Elettrodomestici
F15: Dryer connector is always active
1. Check the efficiency of the terminals on the CNI connector board
2. Overhaul connector connection
3. Overhaul the pressure sensor connection
4. Replace the connector

mod.AWD121NA page 17
5. Replace pressure sensor
6. Replace the board
F16: Non-functioning basket block
1. Go over connector card CNC
2. Go over connector basket block
3. Control Continuity of cabling CNC / basket block and basket block supply
4. Replace basket block
5. Replace card
N.B.From Fault F01 to fault F11
These are shown by LEDs in stand by/on in LVB2000 machines Ariston/Indesit.
From fault F01 to fault F12
These are shown in a display located on the instrument panel of LVB2000 ma-chines
Evolution Indesit.
From fault F01 to fault F15
Are those that are indicated according to the version via LED stand by/on or
display positioned on the Wash Dry machine Ariston/Indesit panel.
4. Replacing the card
Should you have to replace the card:
· retrieve the EEPROM from the old card
· reassemble the EEPROM onto the new replacement card (without EEPROM)
In the event, and only in this case:
· an F02 has been detected
· the above-mentioned checks have been carried out and no problems have been detected on the wiring or to the motor
· the card fitted onto the washing machine is a 12 or 20 version (the version is indicated by a label on the module-containing box
with SW20 or SW12)
you should:
· fit on a new card (version 32 or above)
· fit on an updated EEPROM to request from the assistance service centre, stating the code (e.g. 80xxxxx0000 or 46xxxxx0000),
the serial number and the washing machine model.
n1040242: Power card with welded eeprom.
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
From serial number 20304.0001, IDC power card with welded eeprom is used to ensure the perfect connection of all parts, in the
Comunanza, Teverola and Brembate factories.
To replace the module with welded eeprom, it will be necessary to use the eeprom indicated in the SAT document of the model
concerned.
To replace the module on a unit with welded eeprom both the SAT module and the eeprom are required, because the latter cannot
be reused.

mod.AWD121NA page 18
n1040349: Introduction of 150° Zamac hinge on Ariston 46 models.
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
From serial no. 50207.0001, all Ariston models produced in the Teverola factory (see table 001 attached) with industrial code
(given on the rating plate) starting with 46, have been equipped with a Zamac hinge with 150° opening angle, code C00115666
(see Fig.001).
This modification has involved the introduction of the following items:
Code C00115670 - Complete door EVOII 150° white 27 with standard glass;
Code C00115674 - Complete door EVOII 150° white 27 with long glass;
Code C00115667 - EVOII body for 150° hinge white 27;
The premodified items are not interchangeable separately with the modified ones.
Code C00110133 - Complete door EVOII Standard 180° white 27 standard glass;
Code C00092157 - Complete door EVOII 180° white 27 long glass;
Code C00096193 - EVOII body for 150° hinge white 27;
The hinge code C00064541 continues to be used on the build-under models produced in the Comunanza factory.
n1040359: Polar White Factory 80 (Comunanza)
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
From serial no. 50315.0001, the new "Polar White" colour is used on all washing machines and washer-dryers produced in

mod.AWD121NA page 19
factory 80 in place of White 27.
The third last number of the Industrial Code given on the rating plate of the modified models is 9 (e.g. 80286390900).
To determine the new Polar White codes, it is necessary to know the industrial code or serial number of the appliance being
repaired.
The new items, which bear the initials "PW" in place of "B27", are not aesthetically interchangeable with premodification items
as the whites are different. Both colours will be available for some time.
The items affected by this modification are:
Body, rear panel, top, control panel, handles, buttons, knobs, knob disc, door and plinth.
n1040371: The T4 mechanism type 4.
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
From serial number 30612.0001, the T4 mechanism has been introduced on some oscillating units.
The new tub units are perfectly interchangeable with the premodification ones and therefore maintain the same SAT codes.
The modification especially concerns the basket cross element and the tub cross element assembly that are specific for the new
mechanism.
For servicing the products both the premodification tub cross element assembly (code 074213) and the new assembly (cod.
096077) must be managed; their use is indicated by the serial number of the relevant product.
The relevant Sat codes are:
TUBS (they maintain same SAT code as the premodification parts).
Models “Evizzati “ Serial number > 30312.0001 and < 30616.0001
SAT code 094279 TUB 46L.B5 CV5 EVO II 1200 rpm;
SAT code 094281 TUB 46 L. B5-CV5 LD EVO II 1200 rpm LD;
SAT code 094287 Tub 40 litres b5-cv5 40 litres 1200-1400 rpm;.

mod.AWD121NA page 20
Models Serial number <30312.0001 and > 30616.0001.
Cod. SAT 092257 OUTER TANK & INNER DRUM ASSY B5 CV5
Cod, SAT 092263 OUTER- SET 46 L. CV5-B5 LD;
Cod. SAT 092545 OUTER TANK & INNER DRUM ASSY 40 L B5 CV5
CROSS ELEMENT ASSEMBLY AND SINGLE PARTS MANAGED AS REPLACEMENTS.
SAT code 096077 Cross element assembly with seal rings CV4;
SAT code 096186 Seal ring CV4;
SAT code 013563 Bearing 6205-2Z SKF;
SAT Code 002591 - Bearing 6204-2Z SKF;
On 1200 rpm models, which indicate replacement of the drum with spider in aluminium, with a spider in red ghisa (LVA cod.
C00094280 and LVB cod. C00094282), the following pocedure will need to be followed:
1) Remove the upper counter-weight;
2) Position the balancing springs inside the support holes found further back than the previous position on the cabinet (see
fig.001);
3) Affix the shock absorbers on the support holes positioned on the back part of the cabinet (see fig.002).