Arkon SLIM-GRIP SM427 User manual

SM427
|Bicycle Handlebar Mount with Universal Holder
The Mobile Mounting Specialists™
®
Consumer Hotline:
USA [phone]
INT’L [phone]
Monday - Friday 9 am - 5 pm, PST
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in China
© Copyright 2010 Arkon Resources, Inc.
Package Contents:
(1) SM050-2 - Slim-Grip™ holder for Apple iPhone and iPod touch®
(1) CM011-2 - Sun visor mount
(1) SP-SBH-KIT - Swivel Ball Head
(1) AP2T17MM - Dual T-Tab Swivel Ball Adapter
Compatible with the following devices:
Apple iPhone® 4•
Apple iPhone® 3GS•
Apple iPhone® 3G•
Apple iPhone® Original•
Apple iPod touch® - All models•
IPM511
|Slim-Grip™ Holder with Auto Sun Visor Mount for Apple iPhone® and iPod touch®
82 mm
expandable to
118.5 mm
C
C
C
C
D
D
Install the Support Legs to the Holder
Step 1. Insert the holder support legs (C) by sliding them into the
support leg grooves (D) on the top and bottom of the holder.
Continued on other side...
!Safety Precautions
Do not install Arkon products over an air bag cover or within the air
bag deployment zone. Arkon Resources, Inc. assumes no responsi-
bility of liability for injury or death as a result of car crashes and/ or
air bag deployment.
Arkon is not responsible for any damages caused to your car, your
device, or yourself due to the installation or use of this pedestal mount.
CM011-2
Sun Visor Mount
SP-SBH-KIT
with AP2T17MM
Swivel Ball Head
Adapter
!Note: Arkon strongly recommends using the visor mount
on the passenger side sun visor. Using this mount on the
driver’s side visor will reduce the driver’s view of the road.
Do not place device car charger cords in or near an air bag
deployment zone.
Sun Visor Mounting
Lower the vehicle sun visor and place the clip mount over
the top of the visor. Slide the mount left or right to adjust
the location on the visor.
Step 1.
Connect the dual T-slots (A) on swivel ball adapter to the dual
T-tabs (B) on the sun visor mount.
B
Connecting the Swivel Ball Adapter to the Dual T-Tab Mount
Step 1.
A
*Apple®, iPhone®, and iPod touch®are trademarks of Apple Computer, Inc. Arkon Resources, Inc. is not affiliated
with Apple Computer, Inc.
SM050-2
Slim-Grip™ Holder
for iPhone & iPod touch
CM011-2
S
un Visor M
o
B
Connect the dual T-slots (E) on holder to the dual T-tabs (F) on
the pedestal head.
Connecting the Slim-Grip™ Holder to the Swivel Head Adpater
Step 1.
FE
Optional Cord
Optional Cord
Catcher
Catcher

The Mobile Mounting Specialists™
®
Consumer Hotline:
USA [phone]
INT’L [phone]
Monday - Friday 9 am - 5 pm, PST
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in China
© Copyright 2010 Arkon Resources, Inc.
IPM511
|Slim-Grip™ Holder with Auto Sun Visor Mount for Apple iPhone® and iPod touch®
!Safety Precautions
Do not install Arkon products over an air bag cover or within the air
bag deployment zone. Arkon Resources, Inc. assumes no responsi-
bility of liability for injury or death as a result of car crashes and/ or
air bag deployment.
Arkon is not responsible for any damages caused to your car, your
device, or yourself due to the installation or use of this pedestal mount.
Adjusting Holder to Fit Phone
I
I
If necessary, adjust the support legs (I) on top and bottom by
sliding them laterally to avoid any buttons or ports that may be
on your phone.
Step 1.
Secure holder with your hand for support, as spring-loaded
mechanism requires significant force to operate. Hold your phone
and insert into universal holder by pushing down on the bottom
spring-loaded support legs with moderate amount of pressure
(G). Slide the top of the device under the top support legs (H) until
it fits snuggly in the holder.
Insert Phone into Holder
H
G
Step 1.