Arkon TT136 User manual

Choose the best location on vehicle to place the mount.
Clean o dash or console surface with alcohol cleaning pad and
let dry. (A) Do not attempt application of the dash mount if the
temperature is below 68°F (20°C).
Remove paper liner from adhesive on base (B) and ax adhe-
sive to the dash or console. (Let stand at room temperature for
24 hours before using.)
Adjust the angle of the pedestal head by bending the exible
metal strip (C). Rotate the strip and tighten the base cap. (D)
!Safety Precautions
Do not install Arkon products over an air bag cover or within the air
bag deployment zone. Arkon Resources, Inc. assumes no responsi-
bility of liability for injury or death as a result of car crashes and / or
air bag deployment.
Arkon is not responsible for any damages caused to your car, your
device, or yourself due to the installation or use of this pedestal mount.
The Mobile Mounting Specialists™
Consumer Hotline:
USA [phone]
INT’L [phone]
Monday - Friday 9 am - 5 pm, PST
TT136
|Bendable Adhesive Dash or Console Mount for TomTom® GPS
CM021-SB-2
Benadble Adhesive
Dash Mount
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in China and Taiwan
© Copyright 2008 Arkon Resources, Inc.
Package Contents:
(1) CM021-SB-2 - Bendable adhesive dash mount
(1) APTTO - Adapter plate for TomTom ONE™ Series
(1) APTTOXL - Adapter plate for TomTom ONE XL / XL • S™ Series
(1) APTTGO520 - Adapter plate for TomTom GO™ Series
(1) APTTEP - Adapter plate for TomTom EasyPort™ Series
Step 1.
Step 2.
Dash or Console Installation
TomTom Device Compatibility:
TomTom ONE 130, ONE 130-S (TomTom EasyPort Mount)
TomTom ONE (US Edition, US 3rd Edition)
TomTom ONE XL (1st Edition) - TomTom ONE XL-S (1st Edition)
TomTom ONE 22, ONE 22 Regional, ONE 22 Regional Trac
TomTom XL 22, XL 22 Regional (TomTom EasyPort Mount)
TomTom XL 330, XL 330-S (TomTom EasyPort Mount)
TomTom ONE UK / EUROPE (NEW Edition aka 2nd Edition, 3rd Edition)
TomTom GO 520 / 530 / 720 / 730 / 920 / 920T / 930
APTTGO520
Adapter plate for
TomTom GO
Check Compatibility
APTTOXL
Adapter plate for
TomTom ONE XL
and XL • S
Check Compatibility
APTTEP
Adapter Plate
for EasyPort
Check Compatibility
Patent
Pending
APTTO
Adapter plate for
TomTom ONE
Check Compatibility
TomTom, ONE, GO, and EasyPort are product names, trademarks, or registered trademarks of
TomTom International BV. Arkon Resources, Inc. is not aliated with TomTom International BV.
Step 1. Slide the adapter plate up into the grooves on the back of the
TomTom ONE, ONE XL, or ONE XL • S.
TomTom ONE, ONE XL, and ONE XL • S Plate Installation
Step 1. Attach the adapter plate by sliding it up into the slot on the
back of the TomTom GO 520, 530, 720, 730, 920, 920T, and 930
models device as shown below.
TomTom GO Adapter Plate Installation
!Do not place mount in or near an air bag deployment zone
or where it will obstruct view of the road.
AB
DC

!Safety Precautions
Do not install Arkon products over an air bag cover or within the air
bag deployment zone. Arkon Resources, Inc. assumes no responsi-
bility of liability for injury or death as a result of car crashes and / or
air bag deployment.
Arkon is not responsible for any damages caused to your car, your
device, or yourself due to the installation or use of this pedestal mount.
The Mobile Mounting Specialists™
Consumer Hotline:
USA [phone]
INT’L [phone]
Monday - Friday 9 am - 5 pm, PST
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in China and Taiwan
© Copyright 2008 Arkon Resources, Inc.
Connect the dual T-slots (E) on the back of the adapter plate
to the dual T-tabs (F) on the dash pedestal head.
Connect the dual T-slots (E) on the back of the adapter plate
to the dual T-tabs (F) on the dash pedestal head.
Step 1.
Step 1.
TomTom EasyPort Device Attachment
TomTom EasyPort Device Attachment
Step 1. While holding the adapter plate, gently insert the device
(not included, sold separately) into the adapter plate until
an audible click is heard.
TomTom EasyPort Adapter Plate Installation
TomTom ONE and ONE XL Device Attachment
Connect the dual T-slots (E) on the back of the adapter plate
to the dual T-tabs (F) on the dash pedestal head.
Removal of Dash Mount
To remove the dash mount completely, use a cotton swab
dipped in isopropyl alcohol. Simply peel up a corner of the
dash mount adhesive and swab under the pad while gently
pulling until the adhesive begins to release. Remove slowly.
No damage will occur from the adhesive if it has been properly
installed and removed per these instructions. You may see a
slight discoloration between this area and other parts of your
dash due to fading caused by the sun.
Step 1.
Step 1.
TomTom GO Series Device Attachment
E
F
E
F
TT136
|Bendable Adhesive Dash or Console Mount for TomTom® GPS
E
F