Arlec AM612 User manual

AM612
INSTALLATION & OPERATING INSTRUCTIONS
Door & Window Protection Alarm
INTRODUCTION
This is a wireless security alarm designed for the home, workshop or small business. It has
been developed to be easy to set up and operate, giving both your family and yourself the
security and peace of mind that you deserve. This system detects entry to your premises by
using a Magnetic Window/Door Tamper Detector trigger that alarms when a window or
door is opened.
1. Open the AM612 Alarm and determine where it is to be located. The Window & Door
Sensor is usually placed on front or rear doors but can also be used to secure windows.
2. Remove battery cover on the control panel and place 2 x AA alkaline batteries in the
compartment. Replace cover.
3. Prepare the installation of the Control Panel by putting one screw (screw head less than
7mm dia.) in your desired location at a convenient height above the floor and 32.5mm
from the edge of the door frame. Mount the Control Panel using the hang hole on the rear -
the unit should be flush with the edge of the door frame - then secure the Control Panel from
the front using the lower hole.
4. Install the reed switch using screws provided. Proper positioning of the Window/Door
Sensor is important. Ensure that the wireless reed switch sensor and magnet are parallel
and the arrows are pointing directly at one another. Separation between the pieces must
not exceed 10mm or the unit will trigger (Fig_01).
INSTALLATION

A security code should first be entered using the Control Panel
keypad. This security number can be selected by you and is
used to arm and disarm the unit. Enter your security code as follows:
Enter the factory preset security code ‘11’ then press ‘ * ’.
(A single beep will be heard and the green LED will flash).
While the LED is flashing enter your own security code (up to four
digits) then press ‘ * ’ again. (A musical tune will be heard).
To change your security code, repeat the above instructions but use
your old security code instead of the factory preset number.
Arm & Disarm
Arm the unit by simply entering your security code then press the ‘ # ’
button and a single long beep will be heard. The green LED will light
for approximately 30 seconds (exit delay). Thirty seconds after you
arm the system, the green LED will extinguish and the system will
become fully armed.
When the door is opened and the secured area is entered, the
Control Panel will beep once to indicate that you have 8 seconds in
which to disarm the unit. To disarm, simply re-enter your security code
and press the ‘ # ’ button. The unit will emit a double beep to indicate
that it is now disarmed.
If the unit is not disarmed within the 8 seconds, the piezo siren will
emit a loud sound to alert the occupants of the house to an intruder.
To disarm the unit under these circumstances, simply re-enter your
security code and then press the ‘ # ’ button.
Panic Button
The panic button can be pressed at anytime. This will cause the unit
to emit a siren sound and flash the green LED as if it has detected an
intruder. WARNING - once pressed, the alarm will sound for 1
minute and shut off automatically unless turned off by entering the
security code followed by the ‘ # ‘ key.
Fig.01
PROGRAMMING
1
4
7
*
2
5
8
0
3
6
9
#
PANIC
Arlec guarantees this product against defects of materials and workmanship for a period of 12 months
from the date of purchase provided that the product is used in accordance with Arlec’s recommendations
and within such voltage and current limits as are specified by Arlec in relation to the product. Arlec will at
its own option make good, replace with the same or similar product, or provide credit for any product
manufactured or supplied by it, which proves to be defective within the limits set out above provided that
no repairs, alterations or modifications to the product have been undertaken or attempted, other than by
the company or its authorised agents. Should the purchaser wish to make a claim under the guarantee, the
product should be returned pre-paid to the place of purchase. This guarantee is in addition to and does
not take away from any rights available to the consumer under the Trade Practices Act and the State
consumer protection legislation.
Proof of Purchase
• Please retain your purchase receipt for all
warranty claims.
SPECIFICATIONS
GUARANTEE
For all Sales enquiries
Phone [phone]
Fax [phone]
CPIN002028
Magnet
WALL DOOR
Control Panel
Entrance delay time 8 seconds
Exit delay time 30 seconds
Alarm sound reset
time
1 minute
Intruder indication Green LED will flash
after resetting of alarm
to indicate a burglar
was detected.
Alarm output approx. 110dB at
1 metre.