ARMATURA OmniAC20CAPQ User manual

OmniAC20CAPQ
Installation Guide
Version: 1.1

1
How to Install the Device?
Installation Environment
Please refer to the following recommendations for installation.
AVOID DIRECT
SUNLIGHT
AND EXPOSURE
AVOID GLASS
REFRACTION
KEEP EFFECTIVE
DISTANCE
0.3-2.5m
KEEP DISTANCE
10ft
6.5ft
window
Fix the Backplate on the wall using wall mounting screws.
Attach the device to the Backplate.
Fasten the device to the Backplate with a security screw.
Attach the mounting template sticker to the wall, and drill holes according
to the mounting paper.
4
21
3
①
②
With Backplate:
1.
2.
3.
4.
Device Installation
59.06" / 1.5m

2
1.
2.
3.
4.
Fix the Back Cover on the wall using wall mounting screws.
Attach the device to the Back Cover.
Fasten the device to the Back Cover with a security screw.
Attach the mounting template sticker to the wall, and drill holes according
to the mounting paper.
With Back Cover ★:
1
55.12" / 1.4m
2
3
①
②
4
Note: Features and parameters with mark are not available in all devices. ★

3
Wiring Diagram
Power Connection
1) 12V ± 10%, at least 1500mA.
2) To share the power with
other devices, use an
AC Adapter with higher
current ratings.
12V Recommended AC Adapter
Ethernet Connection
Click on [COMM.] > [Ethernet] > [IP Address] , input the IP address and click on [OK].
IP address: 192.168.1.130
Subnet mask: 255.255.255.0
Default IP address: 192.168.1.201
Subnet mask: 255.255.255.0
Connect the device and computer software over an Ethernet cable. As shown in
the example below:
PC
Note: In LAN, the IP addresses of the server (PC) and the device must
be in the same network segment when connecting to the software.

4
Wiegand Reader Connection
Note: 485A and 485B can be connected to the Barrier gate or the 485
Reader, separately, but cannot be connected to the gate and reader at the
same time.
485A
485B
WD0-OUT
WD1-OUT
INWD0
INWD1
GND
12VOUT
GND
+12V
GND
WD1
WD0
Wiegand
Reader
WD0
WD1 Access
Controller
485A
485B
WD0-OUT
WD1-OUT
INWD0
INWD1
GND
12VOUT
+12V
GND
RS485 Connection
485+
485-
485 Reader

5
Door Sensor, Exit Button, Auxiliary Connection
GND
COM
NC
NO
SEN
BUT
AUX
ExitButton
COM
NO
+
-
Detector
Power
Smoke
Detector
Door
Sensor
Lock Relay Connection
The system supports Normally Opened Lock and Normally Closed Lock.
The NO LOCK (normally unlocked when power-on) is connected with 'NO'
and 'COM' terminals, and the NC LOCK (normally locked when power-on) is
connected with 'NC' and 'COM' terminals. Take NC Lock as an example
below:
1)Device not sharing power with the lock 2)Device sharing power with the lock
GND
COM
NC
NO
SEN
BUT
AUX
Normally Closed Lock
DC12V
FR107
Maximum 30V 3A input.
GND
+12V
DC12V
DC12V
GND
COM
NC
NO
SEN
BUT
AUX
FR107
GND
+12V
Normally Closed Lock
Do not reverse the polarity.

6
Alarm Connection
BELL+
+
-
-
Alarm Power
Alarm
BELL-
AL+
AL-
+