armen LIVING ASTORIA QUEEN BEDFRAME User manual

PRODUCT ASSEMBLY INSTRUCTIONS
Item#: ASTORIA QUEEN BEDFRAME
# Picture Description Quannity
A Headboard 1
B Siderail 2
C Footboard 1
DMiddle Support Bar 1
E Slat 16
F Frame Bracket 4
GLeg Set 2
HMiddle Leg 2
IBolt - M8 x 20 48
K Washer - Ø19 mm 48
L Lock Washer - Ø12 mm 48
MAllen key Wrench V4 1
N Bolt - M8 x 40 mm 2
O Bolt - M6 x 90 mm 4
PInsert Nut - M6-thread 4
QSrew - M4 x 30 8
R Dowel - Ø10 x 30 8
S Washer - Ø16 4
T Lock Washer - Ø12 4
·Step 1: Make sure it's on a safe surface where the bedframe cannot be
scratched and or damaged and close enough to the location
·Step 2: Locate the headboard and the two frame brackets, as these will
be the first to be attached.
·Step 3: Using the Allen Key you will screw in the headboard and the
frame brackets using (4 Bolt - M8 x 20mm; 4 Lock Washer -Ø12mm; 4
Washer - Ø19mm) for each bracket. First place the two washers and
bolt on the interior of the frame using the Allen Key.
i. Repeat for each bracket and make sure it's firmly attached to the
headboard.
ii. Locate the dowel, and place 1 on each bracket on the outside of
the bracket.
·Step 4: Locate the leg set as this will be
assembled onto the preassembled heard board
and rails.
·Step 5: Using the Allen Key you will screw in
the headboard and the one set of leg using (4
Bolt - M8 x 20mm; 4 Lock Washer -Ø12mm; 4
Washer - Ø19mm) for each bracket. First place
the two washers and bolt on the interior of the
frame using the Allen Key.
M
I
L
K
G
M
I
L
K
A
R
F
F
Helpers needed to assemble: 2
Estimate time frame to assemble: 1 Hour
Tools Needed not Included: Phillips Screwdriver

·Step 6: Proceed to locate the end and the two
brackets.
·Step 7: Using the Allen Key you will screw in the
end and the frame brackets using (4 Bolt - M8 x
20mm; 4 Lock Washer -Ø12mm; 4 Washer -
Ø19mm) for each bracket. First place the two
washers and bolt on the interior of the frame using
the Allen Key.
·Step 8: Locate the dowel, and place 1 on each
bracket on the outside of the bracket.
·Step 9: Locate the leg set as this will be assembled
onto the preassembled footboard.
·Step 10: Using the Allen Key you will screw in the
footboard and the one set of leg using (4 Bolt - M8
x 20mm; 4 Lock Washer -Ø12mm; 4 Washer -
Ø19mm) for each bracket. First place the two
washers and bolt on the interior of the frame using
the Allen Key.
·Step 11: Now that we've preassembled parts, we
will connect the headboard and the siderails.
·Step 12: Locate the 2 siderails as this will be
assembled onto the preassembled footboard and
headboard.
·Step 13: Using the Allen Key you will screw in the
headboard and the one side rail (4 Bolt - M8 x
20mm; 4 Lock Washer -Ø12mm; 4 Washer -
Ø19mm) for each bracket. First place the two
washers and bolt on the interior of the sideboard
frame using the Allen Key.
·Step 14: Now that we've preassembled parts, we
will connect the footboard and the siderails.
·Step 15: Using the Allen Key you will screw in the
footboard and the one side rail (4 Bolt - M8 x
20mm; 4 Lock Washer -Ø12mm; 4 Washer -
Ø19mm) for each bracket. First place the two
washers and bolt on the interior of the sideboard
frame using the Allen Key.
M
I
L
K
G
M
I
L
K
B
B
M
I
L
K
M
I
L
K
C
F
R
F

·Step 16: Now that we've connected the headboard
and footboard with the side rails, we will proceed to
reenforce.
·Step 17: Using the Allen Key you will screw in the
siderail from the inside and outside of the frame using
(2 Bolt - M6 x 90mm; 2 Lock Washer -Ø10mm; 2
Washer - Ø16mm) for each bracket. At the same time,
you need to place a (Insert Nut - M6 thread) on the
inside of the frame where the bolt will lock into. And
repeat for another side.
i. Repeat Step 16-17 for each bracket connecting
on the headboard and side rails frame.
·Step 18: Now that we've connected the headboard
and footboard and reinforced the frame, we will start
to insert the middle support bars.
·Step 19: Locate the middle supports bar and 2
middle legs as this will be assembled onto the
preassembled frame.
·Step 20: Using the Allen Key you will screw in the leg
down onto the middle support bar (Bolt - M8 x 40mm)
for each leg.
i. Repeat Steps 19-20 for each leg.
·Step 20: Once assembled, place the preassembled
middle support bar on the frame to set evenly equal
on both the headboard and footboard.
·Step 21: Locate the slats as they will be assembled
onto the preassembled frame.
·Step 22: Using a Phillips Screwdriver you will screw
down the slats down onto the side rails (Screw - M4
x 30mm) for every 4 slats.
·Step 23: Test that the bedframe is firmly on the
ground and the bedframe does not wiggle.
·Step 24: Enjoy your new bedframe.
D
H
H
N
M
D
Q
O
M
TSR
BACK

Product Assembly Instructions
ASTORIA - DRESSER 6DRWS
1/2
D: Bolt / M8*40mm x 8
E: Washer
x 10
F: Washer
x 10
G: Allen wrench x 1
H: Bolt / M4x40
x 12
B: Leg x 4
A: Chest x 1
C: Leg x 1
STEP 1
G
D
F
E
HH
C
I: Bolt / M8*20mm
x 2
E
F
I
G
STEP 3
STEP 2
A
B
B
B
B

STEP 3
FINISHED
STEP 2
3
O
2
O
1
O
K: Insert nut M6*50mm x 4
L: Screw M4*20 x 4
M: Screw M4*40 x 4
N: Anti flib A x 4
O: Anti flip B x 2
STEP 1.1
STEP 1.2
2/2
STEP 1.3
N
L
K
N
M
O

GG
PRODUCT ASSEMBLY INSTRUCTIONS
Item#: ASTORIA NIGHSTAND
Helpers needed to assemble: 1
Estimate time frame to assemble: 30 minutes
Tools Needed not Included: Phillips Screwdriver
#Picture Description Quannity
ANighstand 1
BLeg 4
CBolt - M8 x 40 8
D Flat Washer Ø19 mm 8
ELock Washer Ø12 mm 8
FAllen Wrench V4 1
GBolt - M4 x 40 4
H Handdle 2
A
B
B
B
B
F
C
E
D
·Step 1: Place the nightstand on its length side on the floor as seen. Make sure it's on a safe surface where the table cannot be scratched
and or damaged.
·Step 2: Align the leg with the nightstand holes as seen.
·Step 3: Identify the first leg and the bolt in using the Allen Key as follows (2 Bolt - M8 x 40mm; 2 flat washers; 2 lock washers) per leg.
·Step 4: Using the Allen Key you will tighten the bolts until the leg is firmly attached.
i. Repeats Steps 2-4 for each leg.
·Step 5: Proceed to flip the dresser back upright.
·Step 6: Identify the handles that will be screwed into the drawers.
·Step 7: Bolt in the handles using the Phillips Screwdriver as follows (2
Bolt - M4 x 40mm) per handle.
·Step 8: Using the Phillips Screwdriver you will tighten the bolts until
the handle is firmly attached.
·Step 9: Test the nightstand is firmly on the wall and
ground and the dresser does not wiggle.
·Step 10: Enjoy your new nightstand.
H