Armstrong ExpressPack User manual
ExpressPack®
Installaon and Operaon Manual
Armstrong
Contents
4
6
7
12
13
Limited Warranty and Remedy 1 4
4
General Safety Informaon
You recently purchased the ExpressPack®, and we hope you enjoy this product. Thank you for
-
device.
To get the best results from your device, we recommend to:
•
•
• -
•
•
•
Our team will be pleased to be of assistance !
SAFETY WARNINGS AND SYMBOLS USED IN THE MANUAL
Danger of scalding !
away.
Möbius strip.
Some components of the device are recyclable, the user is responsible for the removal
of these.
5
General Safety Informaon
GENERAL
of the ExpressPack®.
Maintenance, service, repairs, as well as the study of the risks and dangers associated with
these operaons must be carried out by qualied, competent and authorized personnel.
INTENDED USE
Improper use could result in serious hazards and damages to the user, third pares and ma-
terials.
STORAGE
WARRANTY
one (1) year warranty.
other than those provided with the device or any use other than what is explicitly stated, shall
LIABILITY
6
Product Informaon
-
-
STEAM :
MATERIAL : the header and dispersion tubes of our ExpressPack® are made in stainless steel.
NOZZLES :
EXPRESSPACK® COMPONENTS COULD BE SHIPPED LOOSE FOR FIELD ASSEMBLY, MINIMIZING INITIAL COST.
No. ARTICLE DESCRIPTION
1 Header
Condensate outlet
3
5
6
7 Grommets
Figure 1. ExpressPack® and Bill of Materials
7
Product Installaon
unit or inside the duct.
For more convenience, we recommend you to install the ExpressPack® near the duct access.
-
Figure 2.
Do.s & Don.ts of Locaon and Installaon
In case of doubt, do not hesitate to contact your Armstrong agent.
8
Figure 3-1. The ExpressPack® must be
air, do not place the ExpressPack® di-
rectly at the fan outlet.
Figure 3-2. Each ExpressPack® tube
-
tance is met.
Figure 3-3.-
-
Figure 3-4.
Figure 3-5. If you install a humidity control device,
the device and the ExpressPack®.
Figure 3-6.
ExpressPack®. If ExpressPack® is smaller than the
-
Figure 3-7. -
-
5 x D
More than 250 mm
longueur distance
d’absorption spéci-
ée inférieure
Specied
absorption
distance
Specied
absorption
distance
Discharge grill
Humidity control device
Dead air
Coil
Dead air
Filter
Fan
Coil
9
Installaon methods
Header located outside the duct*
duct.
If the ExpressPack® is located outside the
-
Header located inside the duct
It is necessary to introduce the ExpressPack®
part.
Figure 4-1. Header located outside the duct Figure 4-2. Header located inside the duct
*
Water seal for condensate drain
with a siphon, like in the example below.
Remember to connect the condensate drain to the waste water system.
Illustraon 4-3.
100 mm
112,5 mm 112,5 mm
100 mm
112,5 mm 112,5 mm
The drain must be equipped with a siphon with water seal (see diagram) or be disconnected from the network and be drained
off through a funnel:
H min. (mm) = P (Pa)/10
with P = absolute pressure of the air handling unit or the ventilation duct
The drain hose must not be directly connected to the public sewerage network.
Posive pressure Negave pressure
10
The ExpressPack® is only to be used with atmospheric steam.
Piping:-
•
•
11
Grommet
Figure 6-1. n°4)
Figure 6-2. n°2)
dispersion tube and the header.
Figure 6-1. Figure 6-2.
Assembly Process
If the ExpressPack® is delivered disassembled, please follow the steps listed below to assemble
1. Place the header of the ExpressPack® on a plate surface
3.
5.
1
2
3
4
5
Figure 6-3. Exploded view
12
Opons
-
Figure 7.
REFERENCE POINT NAME CARACTERISTICS
steam inlet
B
C condensate 13 mm
C
B
13
Troubleshoong
1. Water «sping» from the ExpressPack®
-
See chapter «Water seal for conden-
B. Top of water seal is above the header of the system.
C. Condensate is not properly evacuated.
See the technical manual of the humi-
2. Low or no steam output
See chapter «Water seal for conden-
Check and correct.
than the recommended distances. See the technical manual of the humi-
-
put.
14
Limited Warranty and Remedy
in the manner for which they are intended, that such products shall be free from defects in
-
ranty Period applies, as listed below]. This warranty does not extend to any product that has
DOES NOT MAKE ANY OTHER REPRESEN-
TATIONS OR WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR ANY IMPLIED WARRANTY OF FITNESS FOR
A PARTICULAR PURPOSE.
The sole and exclusive remedy with respect to the above limited warranty or with respect to
-
to the claim, whichever is earlier. IN NO EVENT SHALL ARMSTRONG BE LIABLE FOR SPECIAL,
DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING, BUT NOT LI-
MITED TO, LOSS OF USE OR PROFITS OR INTERRUPTION OF BUSINESS. The Limited War-
Rev 3
Printed in Europe – 2019/01
© 2019 Armstrong International, SA
Table of contents
